Jump to content

2014+ Leveling Kits

bcazier

By bcazier
in Modifications & Accessories

 Share

Recommended Posts

HOTdiggityDOG Enthusiast

HOTdiggityDOG

Posted
Posted

I'm running 305/55/r20 which is the same and no trimming rub a little at full lock turn up or down a driveway that's it and very little

 

 

SuperAllTerrain

Cant speak for the stamped control arms on the newer trucks since I've read different things about them. But if you go one page back 227, i just posted pics of my truck. 305/55/20's with no clearance issues whatsoever. At full lock left/right and hold, it barely ( and I mean BARELY) touches the sway bar but no UCA's. The rub is so light I can't even feel it through the steering wheel. Had to force a couple of sharp U-turns then get under the truck to check. And I also heavily contemplated the 295/55's but was very happy i went with the 305's.

 

 

Sent from my iPhone using Tapatalk

  • Replies 7.7k
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

Saleenpowr
Saleenpowr

So i put my RC 2" level kit and Toyo 295/55/20's on this weekend. Install was simple, just like on my 2011. It definitely helps to have an extra set of hands when wedging that spacer in there. 295/

Saleenpowr
Saleenpowr

Thanks. Here is one more from yesterday. Considering we're getting 8-10 inches of rain the next two days, I won't be taking any better pics soon.  

FH212
FH212

Mine is finally done! After months of research I went with the RC 2.5" level kit front only, stock rear block. 20"x9" Fuel Nutz w/ +1 offset, 33x12.50x20 Toyo M/T tires. No rubbing, No trimming, yet a

Posted Images

HOTdiggityDOG Enthusiast

HOTdiggityDOG

Posted
Posted
Anyone help me out on tire size?

 

2016 GMC Sierra SLT

Stamped Steel Control Arms

Factory 20x9 Wheels - (23220752)

 

Installed 2.5" Rough Country Lift this weekend, with rear blocks.

 

I've read through all posts and nothing is clear, tire rubs on one truck but not the other.

 

I am looking to run Nitto Trail Grappler's 33x12.5x20 (32.76x12.52) or a Nitto Trail Grappler 295x55x20 (32.91x12.52).

 

Will either of these fit without rub, if rub, how much trimming.

 

Thanks for any and all suggestions.

 

 

Cant speak for the stamped control arms on the newer trucks since I've read different things about them. But if you go one page back 227, i just posted pics of my truck. 305/55/20's with no clearance issues whatsoever. At full lock left/right and hold, it barely ( and I mean BARELY) touches the sway bar but no UCA's. The rub is so light I can't even feel it through the steering wheel. Had to force a couple of sharp U-turns then get under the truck to check. And I also heavily contemplated the 295/55's but was very happy i went with the 305's.

 

 

Sent from my iPhone using Tapatalk

 

 

Sent from my iPhone using Tapatalk

jimmyboy8301 Senior Enthusiast

jimmyboy8301

Posted
Posted
Anyone help me out on tire size?

 

2016 GMC Sierra SLT

Stamped Steel Control Arms

Factory 20x9 Wheels - (23220752)

 

Installed 2.5" Rough Country Lift this weekend, with rear blocks.

 

I've read through all posts and nothing is clear, tire rubs on one truck but not the other.

 

I am looking to run Nitto Trail Grappler's 33x12.5x20 (32.76x12.52) or a Nitto Trail Grappler 295x55x20 (32.91x12.52).

 

Will either of these fit without rub, if rub, how much trimming.

 

Thanks for any and all suggestions.

 

 

Cant speak for the stamped control arms on the newer trucks since I've read different things about them. But if you go one page back 227, i just posted pics of my truck. 305/55/20's with no clearance issues whatsoever. At full lock left/right and hold, it barely ( and I mean BARELY) touches the sway bar but no UCA's. The rub is so light I can't even feel it through the steering wheel. Had to force a couple of sharp U-turns then get under the truck to check. And I also heavily contemplated the 295/55's but was very happy i went with the 305's.

 

 

Sent from my iPhone using Tapatalk

 

 

Sent from my iPhone using Tapatalk

I have stamped steel and my tires (305/55) rubbed with stock wheels on s Zone 4.5, OBVIOUSLY a lift is quite a bit different from just leveling. However there are other trucks with the same setup running stock wheels so I'm assuming it has something to do with the shape of the stamped steel UCAs.

 

 

Sent from my iPhone using Tapatalk

disturbedgator Enthusiast

disturbedgator

Posted
Posted

so on my 17 if i have stamped control arms its possible i will have rub with a level on stock wheels and tires? dang i wanted to keep this truck simple, just a level and slightly larger tires on stock rims.

asalinasz39 Enthusiast

asalinasz39

Posted
Posted

so on my 17 if i have stamped control arms its possible i will have rub with a level on stock wheels and tires? dang i wanted to keep this truck simple, just a level and slightly larger tires on stock rims.

Depends on the tire size and brand. Based on all my readings with a 2.5 level we should be able to run safely a 32.8" x 12.3" with no rub on oem wheels. I should be getting finally my 2.5 level this Saturday installed and plan to run later some federal 33x12.5 r20 m/t. On my stock wheels. Worse case scenerio if i get some rubbing i'll throw some 1/4" or 1/2 wheel spacers. But iam pretty confident i should be fine since the tire specs of the federals fall on the above measurements.

 

 

Sent from my iPhone using Tapatalk

HOTdiggityDOG Enthusiast

HOTdiggityDOG

Posted
Posted

Depends on the tire size and brand. Based on all my readings with a 2.5 level we should be able to run safely a 32.8" x 12.3" with no rub on oem wheels. I should be getting finally my 2.5 level this Saturday installed and plan to run later some federal 33x12.5 r20 m/t. On my stock wheels. Worse case scenerio if i get some rubbing i'll throw some 1/4" or 1/2 wheel spacers. But iam pretty confident i should be fine since the tire specs of the federals fall on the above measurements.

 

 

Sent from my iPhone using Tapatalk

Just a heads up on the spacers, you can read 1000+ reviews on how good and reliable they are and i even thought about it at one point if i ever encountered rubbing. But I have 2 buddies who have ran them, one a 1/2 and the other a 1in, both couldn't stand them. Both complained about incredible wheel shake after the install, and one even had his right/front wheel literally fall off his truck while doing 68mph down the interstate.

 

 

Sent from my iPhone using Tapatalk

Jaycreek7908 Enthusiast

Jaycreek7908

Posted
Posted

Just a heads up on the spacers, you can read 1000+ reviews on how good and reliable they are and i even thought about it at one point if i ever encountered rubbing. But I have 2 buddies who have ran them, one a 1/2 and the other a 1in, both couldn't stand them. Both complained about incredible wheel shake after the install, and one even had his right/front wheel literally fall off his truck while doing 68mph down the interstate.

 

 

Sent from my iPhone using Tapatalk

Aye! No bueno lol

Amuro Enthusiast

Amuro

Posted
Posted

I HAD the RC 2.5 leveling lift kit, factory wheels and tires and yes, my driver side tire did rub on the sway bar. Took it off and shipped it back to them, everything back to factory with no rub. I'm still in search of a better quality lift kit but I will not be purchasing RC stuff again. Those plastic spacer that goes under the struts, they both cracked on both sides. It's plastic! Other then that truck rides perfect but it's stock...

jimmyboy8301 Senior Enthusiast

jimmyboy8301

Posted
Posted

Just a heads up on the spacers, you can read 1000+ reviews on how good and reliable they are and i even thought about it at one point if i ever encountered rubbing. But I have 2 buddies who have ran them, one a 1/2 and the other a 1in, both couldn't stand them. Both complained about incredible wheel shake after the install, and one even had his right/front wheel literally fall off his truck while doing 68mph down the interstate.

 

 

Sent from my iPhone using Tapatalk

Were they running hub/lug centric like bora or cheap ones?

 

 

Sent from my iPhone using Tapatalk

Waaazooo Senior Enthusiast

Waaazooo

Posted
Posted

Just a heads up on the spacers, you can read 1000+ reviews on how good and reliable they are and i even thought about it at one point if i ever encountered rubbing. But I have 2 buddies who have ran them, one a 1/2 and the other a 1in, both couldn't stand them. Both complained about incredible wheel shake after the install, and one even had his right/front wheel literally fall off his truck while doing 68mph down the interstate.

 

 

Sent from my iPhone using Tapatalk

If a spacer causes vibration it's likely one of two things, either non-hubcentric or there is a small rock or debris in between one of the two mounting pads. If there are thousands of successful stories and you know of two that's a 99.998% success rate

 

 

Sent from my iPhone using Tapatalk

Korazu Enthusiast

Korazu

Posted
Posted

Hello all.

 

I am somewhat new to customizing a truck as I've had my 2015 Chevy Silverado LTZ Crew Cab for just under 2 years and have only done a couple cosmetic things to it. Finding this forum has not been in the best interest of my wallet! LOL

 

After doing some extensive reading on this topic, I think I have decided to get the RC 2.5" kit but I haven't to decided if I want to keep the 2" blocks or go to 3" as I'd still like to keep some of the rake of the truck. I have also started looking into tires as mine are close to needing to be changed anyways and right now I have my eyes on the following (in the below order of preference):

  • Cooper Zeon LTZ All-Season Tire - 275/60R20
  • Cooper Zeon LTZ All-Season Tire - 285/50R20
  • Nitto Terra Grappler G2 Tire 285/50R20
  • Cooper DiscovererHT Plus Tire 285/50R20

They will continue to be on my stock 20" in rims as cash flow isn't enough yet to get other rims.

 

Please let me know if I am on the right track or any concerns you see with what I am proposing. Thanks for everyone's insight and help.

asalinasz39 Enthusiast

asalinasz39

Posted
Posted

Question for all the leveled trucks with 4x4. Have you guys dropped the differential to alleviate cv angles and avoid some premature wear. Or if not then how many miles have you put on your rig with no diff spacers.

 

 

Sent from my iPhone using Tapatalk

Northernmoris Enthusiast

Northernmoris

Posted
Posted

I'm in the middle of installing motofab 2.5" upper strut kit. I have the spacer on but after turning the strut assembly 180° to remount it the angle on the bottom strut is way off from the lower arm. Can I do the other side and just switch strut from driver to passenger side?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • diyer2
      Towing In Loose Gravel

      By diyer2 · Posted

      I had a boat for many years, never had a problem even with a 2 wheel drive 93 Silvy for 20 years. Good tires, proper use of the gas pedal worked.
    • Chuck FB
      Towing In Loose Gravel

      By Chuck FB · Posted

      I read through that and I won't lie, my eyes rolled at some of the quirks about how it can turn off the trailer braking for example but I can see how it could help control or even up the torque applied to the ground with each wheel in a boat ramp scenario. But of course what it can't do is increase the torque to the wheels if the need is there as it ends up being like driving the four wheel drive version of a two wheel drive ( high range that is ). So far the neighbor that ended up with the 3.0 duramax with the max tow package which meant the 3.73 gears and high range only, I think its been doing ok for what he has been towing but doubt he ventures off into the soft stuff with his holiday trailer. He may have towed his dads river boat locally with it ( he always used his 6.6 duramax before ), I'll have to ask him sometime if he got into a lack of power to the wheels situation as after all that engine produces a lot of torque at low speed once the turbo winds out a bit and I think it has the 10 speed and if so they have a pretty good first gear ratio at 4.70 I see which is vastly better than the 3 or four speed overdrive models of years ago. 
    • diyer2
      OCI, not when but why?

      By diyer2 · Posted

      I did shorter OCI"s for many years without an issue, fights sludge and wear IMO. Recently started using Amsoil, will not do the recommended/advertised miles between changes. 
    • tigers2007
      Oil Fill Tube

      By tigers2007 · Posted

      GM Part Number???
    • Chuck FB
      OCI, not when but why?

      By Chuck FB · Posted

      It definitely seems quite evident that emissions and fuel economy targets rule above the best case scenario of what the engines best health and life could be otherwise. Items like DI and turbo DI engines with their LSPI issues as well as cats being reduced in life if the proper levels of certain additives were allowed to be utilized and so something has to be compromised and as you point out that is the engine protection from sludge, acid and wear which isn't in the manufactures best interest regardless to worry about in this race to profits from higher sales and so if the engines wear out sooner the next sale is closer at hand.    I am hearing that its likely the two new 2027 GM half ton truck engines will call for a 0W-30 oil, now if that is an existing oil I would have to think so but we will see in the coming months. Sadly as you've pointed out to me, over the last number of years the push has been on to reduce the actual operating temperature viscosity within each designated viscosity grade so that 11.5 to 12 range for a 30 weight for example is more in that just above 10 range at 100c along with that temporary viscosity sheer dropping it even further down as per that "energy conserving" designation, not to mention how some oils are not as sheer stable as would be ideal and that mixed with a long OCI paints a picture with a little too much glitter shall we say !.    All that and the warranty gods scaring the vehicle owner into sticking with that watery wine or risk loosing their warranty coverage if they go and use an oil that is of a higher viscosity even if it meets the emissions and LSPI requirements and would never damage the engine but may very well allow for an engines longer life depending on engine use scenarios ... high ambient temps, towing etc that push oils to their limits.

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...