Jump to content

2014 Silverado Battery Replacement Problems

jamesok1

By jamesok1
in Troubleshooting & Recalls

 Share

Recommended Posts

jamesok1 Enthusiast

jamesok1

Posted
Posted

Hi folks! Yesterday I was leaving home depot and my truck wouldn't start. I ended up jumping my truck and bought a new battery (3 years, 50k miles and the original battery seemed about right time to need replacement). I installed the new battery and noticed that my front passenger and rear passenger blinkers were not working. I ended up finding a blown right turn signal fuse and replaced it but am still having issues. Checked all other fuses in all 3 fuse panels and they are ok. When I started the truck I found out that my radio/ac/backup camera were not working as well and that the display constantly says service 4wd. Might also be other issues that I have not uncovered yet.

 

When I connected the positive terminal I noticed a little spark but did not think anything of it. I've replaced batteries before and this seemed nothing out of the ordinary.

 

After researching it seems like weird electrical issues all trace back to the BCM. I believe that the turn signals are controlled by the BCM as well, so this also points to it being the BCM. Does anyone know if a reset is possible for the BCM and if that might help my problem? Most of the BCM items I've found about resetting have to do with security system related issues. Can anyone confirm the correct way to perform a BCM reset? Kinda ticks me off that a simple battery replacement could cause other problems...very easy to engineer in circuit protection to sensitive electronics.

 

Truck is 2014 Silverado crew cab, 4wd, 50k miles.

 

All help is MUCH appreciated! Thanks!

 

 

tbarn Senior Enthusiast

tbarn

Posted
Posted (edited)

Are you sure you connected all the cables and in the correct position? There is no BCM reset except for disconnecting the battery.

Edited by tbarn
Rolling Thunder Enthusiast

Rolling Thunder

Posted
Posted

There is a sequence for connecting jumpers in your owner's manual. Done incorrectly you can damage the electrical system. Only.you know the sequence that you used. See if you can remember it..

jamesok1 Enthusiast

jamesok1

Posted
  • Author
Posted

Thanks for the replies! I will disconnect the battery for a while and reconnect to try and reset the BCM. Not sure why the BCM needs to be reset after just replacing the battery. Some of the other threads say to connect the positive battery terminal to the negative lead after the battery is out of the picture. Thats a common way to remove any charge from a capacitor. Has anyone ever done this?


Thanks for the replies! I will disconnect the battery for a while and reconnect to try and reset the BCM. Not sure why the BCM needs to be reset after just replacing the battery. Some of the other threads say to connect the positive battery terminal to the negative lead after the battery is out of the picture. Thats a common way to remove any charge from a capacitor. Has anyone ever done this?

jamesok1 Enthusiast

jamesok1

Posted
  • Author
Posted

RollingThunder -

 

I connected the jumper cables in the following sequence (which I subsequently found out was WRONG)-

 

1. Negative good battery

2. Positive good battery

3. Negative bad battery

4. Positive bad battery

 

I did not look at the owners manual before I connected the cables. I opened it up and it has all sorts of cautions in there about turning everything (lamps, lights, radios, etc) off before jumping. Also says that doing this could help save the radio. What? Could destroy a radio by jumping the car? Oh well, hopefully folks will read this and not follow my footsteps.

 

FYI - The manual says the correct way to jump the truck is to (these are the highlights and may be different for different models):

1 - turn off ignition of both vehicles

2 - unplug and turn off all unecessary components.

3 - connect the positive cable terminal to the positive of the dead battery

4 - connect the other positive terminal to the positive of the good battery

5 - connect the negative cable terminal to the negative of good battery

6 - connect the other negative to the metal bracket bolted to the engine (has an illustration in manual)

7 - start the vehicle with the good battery and let it run for a while

8 - try starting vehicle with the bad battery.

 

there are specific steps for cable removal as well.

 

Performing the BCM reset now. Will report back what I find but do not have high hopes for this magically solving everything.

jamesok1 Enthusiast

jamesok1

Posted
  • Author
Posted

Also worth noting is that I did not notice anything wrong with my truck after I jumpstarted it. I only had problems after I replaced the battery. There are not any procedures on how to replace the battery in the manual (?), but I suspect that the same rules would apply.

TX_AT Enthusiast

TX_AT

Posted
Posted (edited)

Jamesok1, it seems we r having similar issues. I had a left rear indicator failure for about 2 weeks. The top bulb signal light was not working. Other than that everything worked as it should.

 

I finally decided to change the bulb today & when i was done, the damn thing wouldn't start. It read "Low battery start vehicle", "Service Stabilitrac." After being pissed of a few minutes, i jumped it and it started right up. It had the anti theft indicator on so i turned it off, locked it, tried remote starting it & worked. Left it on for the 10 minute cycle. Then off until later on in the day.

 

Fast forward to 10pm when i was about to take my daughter to see the firework show, NO START!!! SMH

 

I jumped it again, this time with my Whistler Jump Starter. Starts right up! I left her running for 2 hours before shutting her off & going inside. We'll see what happens tomorrow morning.

 

After reading this thread i just hope its a bad battery! Somehow i don't think that's the case with me because when i connected the jumper cables to the trucks battery and then touched the others together to see if there was any charge, there was plenty of spark. Hopefully Im wrong!

 

It all started with a damn signal light bulb!!

 

My truck is also a 2014 with 52k

Edited by TX_AT
Justin101714 Enthusiast

Justin101714

Posted
Posted

I would check the fuse block snapped onto to the top of the battery for any blown mega fuses. A test light works well. Just go from your negative battery terminal to each side of the fuse.

 

 

Sent from my iPhone using Tapatalk

Dale_K Enthusiast

Dale_K

Posted
Posted

I'm just making a guess, but maybe the battery cable is bad. There were known problems with some of the battery cables. Possibly the manipulation of the cable during the battery replacement was enough to loosen the crimp connection on one end or the other of one of the cables.

 

I would try wiggling the cables when you have the next incident to see if it makes a difference. Then replace the cable that seems bad.

 

Like I said, I'm just guessing.

Colossus Senior Enthusiast

Colossus

Posted
Posted

Not sure if they still use fuseable links in this day and age, if they do, check for a blown one somewhere. Have you check all the other fuses and things in addition to the blown turn signal fuse? Boxes under the hood and in the cab.

MaverickZ71 Senior Enthusiast

MaverickZ71

Posted
Posted (edited)

A lot of people on here have had various problems after changing a battery. These new vehicles are very (as in too darned) picky about the procedures you follow. You might unhook the battery, let the vehicle sit for a while, touch the two battery cables together for a couple of seconds, and hook it back up. Lord knows how many batteries I've replaced/recharged/jump started through the years, and I never had a problem until I replaced the battery on my '09 Silverado. I thought it had a voodoo curse until I read on here about unhooking the battery, letting it sit awhile, touching the two battery cables together, and hooking it back up. When I did that, then everything was fine.

Edited by Maverick Z71
  • Thanks 1
TX_AT Enthusiast

TX_AT

Posted
Posted

My problems are gone after installing a new battery. Still keeping my fingers crossed for a few days.

 

Sent from my SAMSUNG-SM-G935A using Tapatalk

jagabom (Esquire) Enthusiast

jagabom (Esquire)

Posted
Posted (edited)

TX-AT, when you hooked up the new battery did did you hook any certain terminal up first or do you think it matters?

Jim

Edited by jagabom
TX_AT Enthusiast

TX_AT

Posted
Posted

I hooked up the Positive first then the ground. Im not sure it matters but that's what i did.

 

Sent from my SAMSUNG-SM-G935A using Tapatalk

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • bwiese
      seat base height *lowering* (base 40/20/40 seat, 2026 1500 WT std cab)

      By bwiese · Posted

      Folks, Have a great new 2026 WT  (std cab, 2.7/4WD) w/base 40/20/40 mech adj bench "fake buckets"  (with lower and upper center console) heavy vinyl seats.  Overall the seats are very comfortable and the vinyl is heavy and appears less likely to 'split out'. Am very tall (6'5")  + a bad back/osteporosis/former hyperparathyroidism so ease/range of movement is a bit restricted.  The truck rides a bit high and I use a nerf step bar w/my left foot to step in, then I put right foot/leg in, drag my butt in  & get seated.  Worked fine in my 2018 RAM quadCab. But I end up dragging my butt over the left raised sidecushsion area of vinyl seat, and due to texture there's fair amount of traction on slide inward.  (ArmorAll didn't improve.) If the seat were even ~1/2" - 3/4" lower it'd be helpful, but base seats just have the forward/backward underseat bail and the side lever for tilt which really doesn't affect seat height.   I really don't want to 'de-puff' the left side sidecushion forming the  fake 'bucket'. I know one company sells 'seat elevator blocks':  but is there a simple way of lowering the height of the driver seat instead?   Thanks Bill W San Jose  
    • bwiese
      on-wheel cellphone control: 2026 1500 WT (2.7L 4WD std cab)

      By bwiese · Posted

      I have a basic 2026 1500 WT  (2.7L/4WD reg cab shorttbed). Comfy, generally happy with electronics/radio - but is there a way I can add switches to steering wheel right-side position (curr. empty) so I can adjust volume, push phone button to voice dial, etc? Bill W San Jose  
    • Tyler Gibbs
      Travel Trailer 2024 2500 HD 6.6 Gas Engine ?

      By Tyler Gibbs · Posted

      The curb weight on a 1 ton crew cab long bed is around 7k lbs.  Now, I don't know where you went to school but 9k is not more than 2x 7k lbs. More than 2x 7k lbs would be 14k+.   With that said, obviously yes you're going to feel a 9k lb trailer when slowing down.  I already said, when accelerating.  When changing lanes?  No.  But if you look at the context of what was quoted, the original person said, "after a mile or two..." which means that would be after the accelerating portion and you're driving a generally steady pace.  Please do learn to read and comprehend.
    • sFrank
      2026 Silverado Range AFM DFM ECU loaction

      By sFrank · Posted

      So I purchased the Range unit for my 2026 and I am seeing different locations suggested for the ECM . Can anyone confirm wither under hood, left side or right side or behind the wheelwell?
    • No F-bdy Bs
      Dave's Auto (custom engine builder) tear down of L8T

      By No F-bdy Bs · Posted

      Like I've said before. Di and Carbon buildup is not that big of a concern. Engine had minimal buildup, and that engine was obviously not super well maintained. Do regular oil changes, and you're gtg as long as the rest of the truck lasts. Also, the High Pressure FP that people ****** about, but can't tell you why.  Now, I wish they'd trash the variable oil pump. No real world issues with them, but I'll gladly eat whatever miniscule MPG it's saving me in favor of more oil at all RPMs.    Curious to see his assessment of the 7.3 compared to the 6.6. I expect he'll praise the port inj, but from a structural standpoint, the 6.6 is as robust as any engine out there.    Not to take away from the 7.3. I feel it's equally as good as the 6.6.     As to heat on the rear cyls, I'd have to see numerous examples before I'd say it's an issue. Especially not knowing the history of that engine. For all is known, they could have blown a rad hose, and ran it hot, and the 2 rear cyls may be the first to get hot in a low coolant situation, but not be an issue aside from that. 

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...