Jump to content

Chirping? noise when accelerating

Music Junkie
 Share

Recommended Posts

Music Junkie Enthusiast

Music Junkie

Posted
Posted

I have a 2014 Silverado LTZ (very high milage - 219,000)  Runs great and still has some power left under the hood.  For the most part, it is in great shape.  It have a strange noise when acceleration or getting up to about 3 or 4 thousand RPM.  It only does it under load, so it is hard to find where the noise is coming from.  In the attached video, it takes place at 12-18s and then again at 40-46s.  It is hard to hear because of the wind noise, but I can't figure out how to isolate the noise any better.  If anyone has any ideas, I would sure appreciate the input.  The water pump was just replaced, and so was the alternator, along with the tensioner pulley.  I admit my limited knowledge under the hood, but I am willing to learn and fix it, if I can.

 

https://youtu.be/PctCm6Ai09Y

  • Replies 37
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

Music Junkie
Music Junkie

Nope, all US units....  My boss does a TON of driving for work, and replaces his truck every 5-7 years, as his mileage is quite high.  The body and interior are immaculate.  The engine does have a lit

sdeeter19555 Senior Enthusiast

sdeeter19555

Posted
Posted

Have the universal joints been replaced? A dry joint will cause a squeak/chatter as it seizes up.

Sent from my SM-G950U using Tapatalk

Darmichar Enthusiast

Darmichar

Posted
Posted

Does it change with engine speed?  What I could hear, sounded like the beginnings of a bearing drying out.  Maybe belt tensioner idler or alternator.

Music Junkie Enthusiast

Music Junkie

Posted
  • Author
Posted

Not to my knowledge.  I will check with the boss.  It is his old pickup that was handed down to me.  If that could be it, that is fairly easy to fix.  Thanks for the input!

mookdoc6 Senior Enthusiast

mookdoc6

Posted
Posted
55 minutes ago, Music Junkie said:

I have a 2014 Silverado LTZ (very high milage - 219,000)  Runs great and still has some power left under the hood.  For the most part, it is in great shape.  It have a strange noise when acceleration or getting up to about 3 or 4 thousand RPM.  It only does it under load, so it is hard to find where the noise is coming from.  In the attached video, it takes place at 12-18s and then again at 40-46s.  It is hard to hear because of the wind noise, but I can't figure out how to isolate the noise any better.  If anyone has any ideas, I would sure appreciate the input.  The water pump was just replaced, and so was the alternator, along with the tensioner pulley.  I admit my limited knowledge under the hood, but I am willing to learn and fix it, if I can.

 

https://youtu.be/PctCm6Ai09Y

219K?  No lifter failures?  AFM still running?  Nobody would believe this....

Music Junkie Enthusiast

Music Junkie

Posted
  • Author
Posted (edited)
4 minutes ago, Darmichar said:

Does it change with engine speed?  What I could hear, sounded like the beginnings of a bearing drying out.  Maybe belt tensioner idler or alternator.

It starts mostly when getting up to 3,000 to 4,000 rpms and stays pretty constant if I keep it there.  If I let off of the gas, it stops instantly.  If I step back on, it starts up again.  Cruising around town at slower speeds and less rpm's does not start it up.  Once I let off of the gas and then ease back on it on the freeway, I can keep it from happening most times.  It really is just when it is under heavier acceleration.  I hope that makes sense.  Alternator was just replaced last weekend, and the water pump and tension pulley were replaced about 3 months ago.  Figured we would replace the tension pulley while we were in there.

Edited by Music Junkie
forgot something
Darmichar Enthusiast

Darmichar

Posted
Posted
2 minutes ago, Music Junkie said:

I hope that makes sense.

That does, and I agree with @sdeeter19555, I'd take a look at the condition of the U-joints in the driveshafts.  It sounds like it's 'tension' based and the most common place for that to happen is the driveline.

Music Junkie Enthusiast

Music Junkie

Posted
  • Author
Posted
4 minutes ago, mookdoc6 said:

219K?  No lifter failures?  AFM still running?  Nobody would believe this....

Pardon my ignorance, but if it was lifters, would it make the sound while rev'd up in neutral?  It only does it while under load (in drive).  I have tried to replicate it while power braking, but it won't do it.  There seems to be an engine safety mechanism in place.  Also, I will have to read up on AFM, as I do not know what that is, at least not by the acronym.

Music Junkie Enthusiast

Music Junkie

Posted
  • Author
Posted
4 minutes ago, Darmichar said:

That does, and I agree with @sdeeter19555, I'd take a look at the condition of the U-joints in the driveshafts.  It sounds like it's 'tension' based and the most common place for that to happen is the driveline.

Thanks!  I hope it is something like this, that can be fixed without too much trouble.

Music Junkie Enthusiast

Music Junkie

Posted
  • Author
Posted
16 minutes ago, Music Junkie said:

Pardon my ignorance, but if it was lifters, would it make the sound while rev'd up in neutral?  It only does it while under load (in drive).  I have tried to replicate it while power braking, but it won't do it.  There seems to be an engine safety mechanism in place.  Also, I will have to read up on AFM, as I do not know what that is, at least not by the acronym.

O.K., AFM is for the management when the cylinders cut off from 8 to 4.  That system has not been replaced to my knowledge.  Could that cause this problem?

aseibel Senior Enthusiast

aseibel

Posted
Posted
30 minutes ago, mookdoc6 said:

219K?  No lifter failures?  AFM still running?  Nobody would believe this....

5 minutes ago, Music Junkie said:

O.K., AFM is for the management when the cylinders cut off from 8 to 4.  That system has not been replaced to my knowledge.  Could that cause this problem?

Hes just asking because this is very high mileage for this truck model. People have wondered about the longevity of the engine with AFM activated. Some people deactivate it because they fear it will cause problems long term.

 

You're not using Canadian KM measurements are you? 219K Miles is a lot for 5 or 6 year old truck.

 

 

 

Music Junkie Enthusiast

Music Junkie

Posted
  • Author
Posted (edited)
On 6/26/2019 at 9:30 AM, aseibel said:

Hes just asking because this is very high mileage for this truck model. People have wondered about the longevity of the engine with AFM activated. Some people deactivate it because they fear it will cause problems long term.

 

You're not using Canadian KM measurements are you? 219K Miles is a lot for 5 or 6 year old truck.

 

 

 

Nope, all US units....  My boss does a TON of driving for work, and replaces his truck every 5-7 years, as his mileage is quite high.  The body and interior are immaculate.  The engine does have a little noise when you first start it up, until the oil gets moving, but nothing very bad.  All in all it is a great truck.  Better than the old one I drove, 2003 Silverado 1500 LT with 174k miles - still have that one and will pass it on to my youngest son who will start driving in 6 months....lol.  I know every mile on that one and it is still nice as well.  This one is just nicer inside.  I don't complain about any of them, as they are company trucks and I don't have to pay for anything.  Quite the deal as far as I am concerned.  Since they take care of me, I like to take care of the trucks and don't mind working on them when I need to.  Figure that is a fair trade off.

Edited by Music Junkie
spelling error
  • Like 2
Music Junkie Enthusiast

Music Junkie

Posted
  • Author
Posted

O.K., I was able to make a couple more sound samples yesterday, and this morning.  I tried recording them with the windows up and the A/C and radio off to see if I could isolate the noise a bit more.  It is a bit clearer.  I also kept on it a bit and then let off and pressed again to show how it slows down and speeds up with acceleration.  Maybe these sound bites will be better.

 

 

Darmichar Enthusiast

Darmichar

Posted
Posted

That sounds like it could be the flapper valve oscillating with the exhaust.  I'd clamp it open and drive the truck and see if it stops making the noise.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • Grumpy Bear
      TCM Tuning 6L80E

      By Grumpy Bear · Posted

      I did the new thermostat after doing a 'flip' for a year. Runs as cool one way as the other in the summer but in the winter there is a bit of a floor. Yellow with the new 70 C thermostat. My data over the life of the unit to date. Still need more cooler. Anyway that floor helped both winter fuel economy and shift quality in the winter. I found it a good balance.       
    • Grumpy Bear
      Food & Drink

      By Grumpy Bear · Posted

      Evan Williams Bottled in Bond   So pouring the last of a bottle of Evan Williams Black label last night I set off the the state store for a refill only to be denied the by an empty shelf. Rats.    What the did have was a bottle of Evan Williams Bottled in Bond. 100 proof. Hum, a few bucks more but a known distiller. Lets have a swing at it. ( I have before )    Cracked it open and pour a serving over ice. Hum.... more heat, yes. More alcohol naturally. But the barreling not the proof brings the taste and this one came up short.    Oh is was familiar but the heat ran the barrel over like a Peterbilt runs over a squirrel. Could use a heavier toasting of the oak me thinks or perhaps a longer barreling. Who knows. But what I can say is ice or a water back isn't the answer. What kills one kills them both. Sad. It is a pleasant drink....if you have little to compare it to.  
    • Grumpy Bear
      Bridgestone vs Goodyear tires?

      By Grumpy Bear · Posted

      I've had exactly one set of Bridgestone. Lasted five year and 125,000 miles and had I known better 15oK would have been a cake walk. I would have bought a like set had they not tripled in price since the first set. I removed them at said mileage with 5/32" remaining in dead even wear all four. They were fuel efficient, quite, comfortable and predictable.    Early on I got a very good alignment checked at least once a year, sometimes twice; kept the tires properly inflated, balanced and rotated. And I've found that many a tire issue can be avoided with great maintenance practices. Lot's of tire dealers will do rotation and balance (simple) for free for as long as you own the tire they sold you so no excuse not to.    Bead prep, alloy integrity and stem health have a huge impact on inflation stability. There are more mountings done poorly that perfectly. Finding a good tire guy is gold and as important as finding a tire you like.    That 3X price increase now two sets of "other tires' later is starting look like a bargain.      Bad maintenance kills more tires than bad tires. 
    • Grumpy Bear
      Wow I'm in a pickle. (Broke down truck) and a story.

      By Grumpy Bear · Posted

      Atlas, you kill me As aggravating as a project like this can be you have been unable to hide your fascination with learning and using that angst against this beast like a Ninjitsu Master. It amuses you, admit it now.      BTW, love your writing style. 😉       
    • TrueBlue
      Wow I'm in a pickle. (Broke down truck) and a story.

      By TrueBlue · Posted

      I gotta say, I'm enjoying your narration. The troubles you've been having are amusing as you describe them. It's good to see that you're finally getting some satisfaction out the old beast though.

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...