Jump to content

Recommended Posts

Posted

Hey guys, does anyone know of a way to disable the V4 mode without having to tune it??

I used the M-5 but it still activates in that mode as well.

 

thanks

 

Posted

Any reason to do this?

 

Just to do as it advertises, stop the truck from going into 4cyl mode. Many do it because of the noise you get in 4cyl mode with aftermarket exhausts.

  • Like 1
Posted

from what I have read, you don't lose much mpg in town just on the highway, would you guys agree with that?

Posted

from what I have read, you don't lose much mpg in town just on the highway, would you guys agree with that?

 

I agree, and you really don't even lose much on the highway.

 

Personally, I was really only able to stay in 4cyl mode around 50-60mph. On the highway (70-80mph), it was just go into 4cyl mode if I was coasting, and that was annoying see if flip over an back a million times.

  • Like 1
Posted

and you can remove it and reinstall it on the fly whenever you want/need to?

  • Like 1
Posted

Correct, just plugs right into the ODBII port.

  • Like 1
Posted

I used the M-5 but it still activates in that mode as well.

?????

 

It shouldn't.

 

BTW, I find the V4 mode less annoying since I started running mid-grade fuel.

  • Like 2
Posted

I have even found mine doesn't come on in M6 mode. I find M5 mode doesn't work for me as I am usually cruising on major roads at higher speeds and need the extra gear

Posted

?????

 

It shouldn't.

 

BTW, I find the V4 mode less annoying since I started running mid-grade fuel.

 

Yep, this.

 

Also, whenever I'm on the highway I use cruise control and I've noticed a drastic increase in MPG as the truck will actually stay in V4 mode longer than if I'm controlling the throttle. Might just be me still getting used to it, but it seems like the cruise is better at the minor accelerations to get up a small hill, etc. and keep it in V4.

  • Like 1
Posted (edited)

 

Yep, this.

 

Also, whenever I'm on the highway I use cruise control and I've noticed a drastic increase in MPG as the truck will actually stay in V4 mode longer than if I'm controlling the throttle. Might just be me still getting used to it, but it seems like the cruise is better at the minor accelerations to get up a small hill, etc. and keep it in V4.

I've also noticed that the cruise is better than my foot for achieving better fuel economy.

 

I've taken to using the cruise as much as possible.

 

 

Currently trying to tell if the grade braking override will also improve economy.

 

 

When I use M7 or less, it stays out of V4, but usually being in V4 doesn't seem to be a problem on this truck, so I almost never is M mode.

Edited by redwngr
  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Latest Articles

  • Posts

    • Hello hello looking forward to expanding my knowledge of the 2026 2500 HD that I just bought.   Truck has 3500 miles on it four-wheel-drive crew cab and I’m about to put a 6 1/2 inch BDS lift on it 18 x 10 -25 offset with 37’s   Already have the wheels and tires just waiting on the lift install in about three weeks   Question what surprises am I not gonna be happy with?  I’m not new to lifted trucks so I know that acceleration towing gas mileage all that is affected..   Question is those of you that have this truck this powertrain with a 10 speed Allison and have done the mods that I’m doing,,, how bad is it? Is that Allison constantly gonna be hunting for the right gear to go into? And what about towing, acceleration, fuel consumption as mentioned?    Lastly how come I can’t find any ring pinion gear set up for these axles and when could I expect to see them?   I apologize if there’s any typos I’m doing speech to text on my iPhone.    
    • I've got a 2013 2500 6.0L Flexfuel. Drove the truck earlier today with no issues. Went to run an errand tonight and noticed key fob wouldn't work. Figured battery was dead, so replaced fob batter. Still wasn't working. Grabbed my other set of keys with the other fob and that one wasn't working either. So I manually unlock truck and insert key. Interior lights come on, dashboard lights up, turn key and truck starts. Turn truck off, like a moron, and try starting again. This time no crank, no click, no nothing. Lights still come on and dash lights up, but now I'm getting a service 4wheel drive, service tire monitor, etc. Check voltage on battery and Im showing 12.2v. Throw my battery charger on it and give it 15 mins and try starting again. But still no crank no start. Decide maybe its a bad battery, run to autozone grab a new one and put it in. Same issue. Disconnect battery and let it sit for 15 mins. Try again and still nothing. I had managed to roll the windows down earlier as its a humid night, but now I can't get them to roll up. Power locks are also not working now. Then randomly I try the key again, and it fires right up. Immediately I roll up the windows as we have nothing but rain forecast this week. I shut it back off wait 30 seconds and start up again. Worked a 2nd time. So turn it off, start putting things back together. Try one more time, and back to no crank no start. And now the car alarm starts going off. Had to disconnect battery and leave it that way for the night as I don't think my neighbors would appreciate my alarm going off again tonight. Any thoughts or help would be appreciated. 
    • No one will care for you like you care for you. Do what you can for as long as you can. IMHO of course. 
    • How about them NICKS!!! 
    • Hi there.  Long time lurker, first post.    i have read the previous posts regarding the water ingress problem with this emblem.  I bought my 1500 SLT the  summer of 2025 new and after reading the MANY problems with these emblems failing I decided to install one anyways.  As per a YouTube video, I sealed ( or tried to) this sign with silicone sealant around the outer perimeter joint and the holes that were already somewhat sealed on the rear plate of the emblem.  And installed the connector assembly using dielectric grease on the connectors. The installation looked great and worked well for about 4 months……then FAILURE.  Grrrrrr…… I live in the great white north and wash my truck weekly in an automatic car wash  to keep the salt off.  Let me tell you that removing the old, failed emblem is a whole different animal than removing the OEM individual letters without removing the grill assembly. Mainly because the illuminated logo is built differently than the original letters which  you can remove the red surface lettering with a knife or some kind of blade which gives access to the tabs which hold the logo onto the grill. So I had to essentially destroyed the old emblem to remove it. Doing so killed my chance of doing somekind of autopsy on the failed , old logo.  But there was plenty of water inside when I ripped it apart.  Prior to installing the new assembly I tried it with the old harness and it works fine.   Does anyone have any insight as to where the water is getting into this emblem? I intend to seal the new logo with slow curing epoxy this time around using a syringe.  I think this newer emblem may be an updated unit which I hope GM got the vendor to fix. It has an October 2025 date on it.    If this one  fails,  I am just going to revert back to the non-illuminated letters….AFTER PULLING THE GRILL.    Any thoughts on sealing with epoxy would be appreciated. Thx!   Doug  
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...