Jump to content

Official 2019 5.3L & 6.2L V8 Engine Specs Are Here


Recommended Posts

Posted
On 5/18/2018 at 2:09 PM, Chainesaw said:

I wish they would - that's the truck I WANT - but no one is offering anything like it.. I was really hoping this year would be the year.... guess I'm keeping my '15 6.2L  - Don't _love_ the new look and with the same HP rating, there really is no reason to trade up. 

10 spd trans is going to make it quicker. Better fuel Econ and 450 lbs lighter. That’s quite the change though. At least they didn’t reduce power like the leaked numbers showed. 

Posted
23 hours ago, kilowhiskey said:

I think the 10 spd will be amazing. They co developed it with ford. 

Yes the mechanical parts are the same as the ford but unfortunately they do not have the same programming.  I am not sure how Ford does with their trans programming but GM cannot make a truck to shift right.  The trans could be a good trans be it 6, 8 or 10 speed but its their programming that gives them a bad rep.  I drove my friends 2017 ram and the 8 speed in his is flawless.  It is always in the gear it should be there is no hesitating when you stomp on it no clunks into a gear and it doesn't appear to have torque management.  The power is there when you want it.

Posted
On 5/24/2018 at 5:41 AM, Payton34 said:

Yes the mechanical parts are the same as the ford but unfortunately they do not have the same programming.  I am not sure how Ford does with their trans programming but GM cannot make a truck to shift right.  The trans could be a good trans be it 6, 8 or 10 speed but its their programming that gives them a bad rep.  I drove my friends 2017 ram and the 8 speed in his is flawless.  It is always in the gear it should be there is no hesitating when you stomp on it no clunks into a gear and it doesn't appear to have torque management.  The power is there when you want it.

Truth be told. That’s one of the reasons I got rid of my rig. The 8 spd didn’t act right at all! I HATE dodge, but you’re right, their trans shift amazing. Not too sure if you’ve driven the f150, but it’s one of the smoothest trucks I’ve ever driven. I hope these new chevys can compete. 

  • 2 weeks later...
Posted
On 6/3/2018 at 10:21 AM, sparky5022 said:

Maybe a stupid question but, is the power steering electric and when did that happen?

 

Started on the K2XX models (2014...1/2 tons only).

  • 2 years later...
Posted

Please help i am trying to do a large audio system in my 2019 truck. That being said i need to add a 2nd alternator with this new stretch belt  i can not do that i need to know what it would take to convert this to a 2018 set up with a tensioner.  Thanks 

Archived

This topic is now archived and is closed to further replies.

  • Latest Articles

  • Posts

    • This is interesting. My quote tagged here is different from my original quote. After I’m driving them longer. That isn’t me. I don’t talk that way. I definitely wouldn’t express myself that way. Interesting.
    • I have the same running boards on my truck and I do agree they are bulky. I also find myself stepping over them when getting in and out of the truck. Besides providing protection to the rocker panels, they aren't very useful.  I will be replacing them soon with the Amp Powersteps. 
    • Monthly payment is only part of the equation. With today's prices and interest rates, I'd look at the total monthly cost: payment, insurance, registration, fuel, maintenance, and expected repairs. A vehicle that fits comfortably into your budget is usually the better choice than stretching for a higher trim. I've also kept my vehicles longer over the past few years. New cars have gotten expensive enough that driving one for 10+ years, while staying on top of maintenance, often ends up being the most cost-effective approach.
    • 10 Ford and Chevy engines proven to reach 300,000 miles   You may note a common 3K OCI on this list of gas motors. I skipped over the diesels. Dh'O. 
    • Thanks newdude!  By the time manual selection is needed, I'm probably too much of a control-freak to depend on the transmission sensing braking to activate automatic downshifting.  I would be anticipating the situation and already be manually downshifting.   This truck replaced a 2004.5 LLY diesel with the Allison 5-speed.  Putting it in T/H made noticeable differences (when the torque converter locked, upshift points, downshift behavior).  On this 2024 gasser with the 10L1000 I haven't been able to detect much, if any, difference.  Ok, I can never tell now when the torque converter locks up.  But I also don't notice differences in shifting.  For downhills, I've probably already manually downshifted by then anyway.  Since it's also more awkward (than the 2004.5) to engage/disengage I don't even bother.  Or maybe it doesn't really matter with just a 3k lb. camper in the bed?   Thanks also for the list of reasons the charging system might select various voltages.  However, what I am seeing doesn't fall into any of those categories.  It very definitely, and very consistently, rises after coasting/braking.  Maybe not immediately, but not very long after coasting/braking.  Very consistently drops voltage when no longer coasting/braking.  It might also be interacting with the camper battery charging (I might disconnect the camper and see if it changes the charging behavior).  I also need to recheck turning on headlights for when I want to force it to charge the camper.   Another JR, in June I converted the camper to LiFePO4.  Since it's not a good idea to try to charge lithiums directly using truck, I installed a Victron Orion XS DC-DC charger (which BTW is AMAZING!!).  Being cheap, I only had to buy that one item (besides the battery, of course) to do the conversion.  The camper OEM 120v battery charger (only 19 years old and works perfectly) and the truck feed the input to the DC-DC charger (not at the same time).  But I didn't want the camper charger feeding back to the truck so I kept the old separator.  I considered replacing the separator with a 30amp diode but that means more work and might add another 1/2 volt drop.  One thing that surprised me was the voltage drop over the long 10awg wire run, so I can only charge smoothly at 8 amps (because the DC-DC charger is completely configurable).  Another reason I don't want an added voltage drop with the diode.  I might also be a little lazy but all this work is being done under the sink with a small cabinet opening.    
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...