Jump to content

Recommended Posts

Posted
On 2/24/2021 at 12:52 PM, Kclyatt said:

Update....Few months into sealing my rear glass and happy to report no further leaks. I recently sealed up my spoiler as a added guarantee because as we can see GM does not have our best interests in mind. I used door trim from Lowes and this particular type has ridges to help with the trim tool to push into the tight space and also has adhesive on the back to hold into place once set. The third brake light I used clear silicone (same type 3M) since that gap was too tight for trim.

 

Hope my enthusiasm to prevent future leaks helps another in this exclusive club of leakers!

trim.1.jpg

trim.2.jpg

Trim.3.jpg

Thank you for sharing this. Can you advise what 3m silicone you used and possibly provide a link? 
 

Thanks again,

JMF

Posted
10 hours ago, jftwist said:

Thank you for sharing this. Can you advise what 3m silicone you used and possibly provide a link? 
 

Thanks again,

JMF

 

4F71134E-0FEC-474F-907F-8679549FEDBE.png

Posted
28 minutes ago, Kclyatt said:

 

4F71134E-0FEC-474F-907F-8679549FEDBE.png

Thank you very much for your assistance. 
 

JMF

Posted

There is another type of self leveling 3m adhesive I believe that is called out in the TSB


Sent from my iPhone using Tapatalk Pro

Posted

Just curious if anyone who has a topper/camper shell if that's helped prevent or stop the amount of water coming in the cab from the rear window? 

Posted (edited)

TSB Sealing Repair Completed – UPDATE

 

Quick background – Picked up my ’21 Sierra on 12/4/20. Within 10 days of ownership I had the leak on both sides at the top of the slider. Dealer completed the TSB, and I could see a heavy bead of the sealer that was laid across the top frame of the slider.  After the TSB was done I didn’t see any leaks and continue to check very closely after every rain. I have a small towel sitting on top of the rear seat back rest just in case the slider starts leaking again. About a month ago during a steady rain I saw a drop of water from the same location - literally a few drips where it was barely leaking, but the towel on the seat back rest was dry to the touch as was the carpeting.

 

As others in this thread have suggested and since it was barely leaking I decided to try the flowable silicone (permatex 81730) rather than have the truck torn apart again. When we had a warm day I cleaned the top of the slider as best I could and also taped off the top of the glass on the slider to try and minimize the mess. I used a full tube of the permatex and made a few passes across the top of the slider frame, being careful to not overfill the area. As other posters have mentioned that have used this product it is thin and runny, so being careful minimizes the clean up.

 

Since using the flowable silicone 4 weeks ago we have had both snow and rain. Over the past week we have had significant rain, including long periods of drizzle, solid rain and heavy down pours. So far no leaks, so the effort was well worth it. I can see along the top of the slider frame where the flowable silicone has dried there is an even layer of silicone across the complete gap. It looks like the permatex product took care of any small gaps that the TSB work didn't completely seal. So far I’m really impressed with the permatex product and will use it again should I see a small leak in the future.

 

Pic below of where it was leaking and also of the permatex product used. Thanks to everyone that recommended this product and the idea.

 

 

leak.JPG

permatex.JPG

Edited by DSW1519
Posted
4 hours ago, DSW1519 said:

TSB Sealing Repair Completed – UPDATE

 

Quick background – Picked up my ’21 Sierra on 12/4/20. Within 10 days of ownership I had the leak on both sides at the top of the slider. Dealer completed the TSB, and I could see a heavy bead of the sealer that was laid across the top frame of the slider.  After the TSB was done I didn’t see any leaks and continue to check very closely after every rain. I have a small towel sitting on top of the rear seat back rest just in case the slider starts leaking again. About a month ago during a steady rain I saw a drop of water from the same location - literally a few drips where it was barely leaking, but the towel on the seat back rest was dry to the touch as was the carpeting.

 

As others in this thread have suggested and since it was barely leaking I decided to try the flowable silicone (permatex 81730) rather than have the truck torn apart again. When we had a warm day I cleaned the top of the slider as best I could and also taped off the top of the glass on the slider to try and minimize the mess. I used a full tube of the permatex and made a few passes across the top of the slider frame, being careful to not overfill the area. As other posters have mentioned that have used this product it is thin and runny, so being careful minimizes the clean up.

 

Since using the flowable silicone 4 weeks ago we have had both snow and rain. Over the past week we have had significant rain, including long periods of drizzle, solid rain and heavy down pours. So far no leaks, so the effort was well worth it. I can see along the top of the slider frame where the flowable silicone has dried there is an even layer of silicone across the complete gap. It looks like the permatex product took care of any small gaps that the TSB work didn't completely seal. So far I’m really impressed with the permatex product and will use it again should I see a small leak in the future.

 

Pic below of where it was leaking and also of the permatex product used. Thanks to everyone that recommended this product and the idea.

 

 

leak.JPG

permatex.JPG

What dealer did the original TSB for you?  I am also in Bucks County, and was thinking of taking it to Faulkner.  

Thanks in advance!

Posted
7 minutes ago, SPASierra said:

What dealer did the original TSB for you?  I am also in Bucks County, and was thinking of taking it to Faulkner.  

Thanks in advance!

I had the TSB done at O'Neil GMC in Warminster. They used an outside glass specialist and they did a good job. I can't even tell the truck had been touched. I bought this truck at O'Neil, and I'm very happy with how they've treated me - both in sales and service. I attribute the slight leak (after the TSB) to the crappy window frame design.  

Posted
1 minute ago, DSW1519 said:

I had the TSB done at O'Neil GMC in Warminster. They used an outside glass specialist and they did a good job. I can't even tell the truck had been touched. I bought this truck at O'Neil, and I'm very happy with how they've treated me - both in sales and service. I attribute the slight leak (after the TSB) to the crappy window frame design.  

Thanks for the quick reply!  I will give them a call!

 

Posted
Thanks for the quick reply!  I will give them a call!
 
No problem. Dave the service manager is a really good guy.

Sent from my Pixel 3a XL using Tapatalk

Posted

I have a 2021 1500 AT4, I've washed it once and didn't notice any leaking. Only 1200 miles on it and I garage it every night. Tagging this thread for when mine does start leaking..

 

Posted
9 hours ago, Wormydog1724 said:

I have a 2021 1500 AT4, I've washed it once and didn't notice any leaking. Only 1200 miles on it and I garage it every night. Tagging this thread for when mine does start leaking..

 

Hopefully you won't need to.

Posted
I have a 2021 1500 AT4, I've washed it once and didn't notice any leaking. Only 1200 miles on it and I garage it every night. Tagging this thread for when mine does start leaking..
 
Washing doesn't usually have enough standing water to get the leak going like sitting in the rain. Wish you luck. So far my 2nd attempt, replaced whole window, has worked.
Posted

Add me to the list, 2020 AT4. Built Nov 2019 in mexico. 17,000 miles. Home garage, and work garage, and live in PHX, so not much water exposure. I'll probably wait a while to see if GM can come up with a good fix.1cb891b6f0ea35301c51b01c23234629.jpg7eebef29ea3335764b63e79080920844.jpg

Sent from my Pixel 5 using Tapatalk

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Latest Articles

  • Posts

    • Compression test? Weird noises? Fuel trims?
    • I suspect at some point in the near future, the hardware will be free and you pay a subscription to access the vehicle - alldata style.
    • I've been eyeing an upgrade to my tonneau cover for a bit now.  Intrigued by the BAK MX4 EZ-Lift with the torsion spring and went for the upgrade.  Thoughts and musings during unpacking, install and a few days of usage.   Once my order went into Realtruck, it took about 4 days to ship.  Unfortunately, FedEx Ground destroyed the box and contents and it was unusable upon receipt.  To Realtruck's credit, one email with pictures and an RMA was sent to me to send the first one back, and another unit was shipped out.  It arrived 3 days later, unscathed.   I opened the box and it looked like every other BAK MX4.   Biggest differences are the rails and retaining clamps, and of course the spring attached to the cover itself.     NOTE - if you are upgrading from a MX4 to the EZ-Lift, you will have to replace the rails.  The EZ-Lift rails have a notch cut in them to allow the new style retaining clamps to fit properly.  The new retaining clamps also have 2 knobs/carriage bolts and there are two tracks underneath the front panel. The strap clips are mildly different (more like the Undercover Flex clamps) in that the screws go in from the underside.  Personally I prefer these over the BAK clamps that use the nutserts that are a nuisance to install.  The remainder of the parts in the box (drain tubes, rail clamps, and bumper pads) are standard issue BAK.     I did not replace my front bed seal at the time because it seemed to be in decent shape.   BAK recommends shims on the GM trucks unless you place the clamps on the flanges about 1/3 of the way in from both the front and rear of the bed.  I shimmed the front and the middle, and initially placed the clamps equidistant.  This also turned out to be a mistake, because when I set the cover in place, the new style retaining clamps wouldn't clear the front clamp.   New style clamp inserted in the track:     And the issue which occurred because the front rail clamp was too far forward:     Once I removed the shim from the front of the bed, and slid the clamp back to the front flange, everything cleared fine.     The cover set on the rails without issue and I installed the strap clamps.  After I completed my adjustments, I pulled the pin to activate the torsion spring.  Mistake #3 on my part.  PULL THE PIN AS THE VERY VERY VERY LAST STEP!  The reason is, once you pull the pin, the torsion spring is activated.  If you have to loosen the front clamps and adjust the cover, the front panel will - by virtue of the spring, refuse to lay down.  The only way to get it to lay down so you can reinstall and tighten the clamps is to fully open the panel against the back of the cab, which will then allow the front panel of the cover to lay down and be tightened.  Not a big deal unless you haven't installed the foam pads yet (typically the last step) because minus the foam pads, you will need to place something between the frame of the cover and the back window so it doesn't get scratched.  The next time I install one I will install the foam pads before I pull the pin and activate the spring.   After using it for a few days:   The spring assist is great.  You literally can open it with one hand.  My shoulders aren't getting any younger and this was part of my motivation to swap out. The second panel latches and unlatches itself as you open and close the cover.  Neat in concept, however it took me a minute to get used to closing the cover and not hearing the "latching" sound that would tell me it was locked in place. The paddle handles are a huge upgrade and I wouldn't be surprised to see them become the standard across the Realtruck line.  They effectively eliminate the concern that a thief could coat hanger the cover open and get to the contents in the bed. I'm not sure why the very front panel on my cover has a different finish from the other 3 panels.  I have a request into Realtruck to find out if mine was not manufactured properly or if it was by design.   All in all I'm pleased.  Same level of protection, looks good, keeps stuff mostly dry (they all leak around the tailgate) and easy to install.
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...