Jump to content

Recommended Posts

Posted
On 4/2/2021 at 11:49 AM, SigPig94 said:

Just spoke with the service manager again......anything other than a sliding rear window is apparently NOT an option (said electrical problems would be a certainty.....??)....so new slider it is.  He also said that the replacement window they’ll be installing next week has a “new part #” so it’s possible that a new repair approach is in effect..... 🤔.  Uhhh...hooray???  The dance continues.......  

 

I don't think you would have any electrical problems. The sliders in these trucks are different from previous years. The motor and gearbox that opens and closes the window will separate now. Meaning they can leave the motor hooked up to the wires but, it won't do anything. I had my window replaced about a month ago. The glass guy came to the house and did the work. Here is the process....

 

Posted
9 minutes ago, 2016 Sierra Owner said:

I don't think you would have any electrical problems. The sliders in these trucks are different from previous years. The motor and gearbox that opens and closes the window will separate now. Meaning they can leave the motor hooked up to the wires but, it won't do anything. I had my window replaced about a month ago. The glass guy came to the house and did the work. Here is the process....

 

Thank you for that.....I saw it earlier when I started reading this string and it is VERY informative....your pics REALLY assist in the understanding of the issue.  I certainly hope this process fixed your water woes......and thanks to great posts like yours I’ll be asking specific questions when I bring my truck in for the window replacement next week. 🍻

Posted
7 hours ago, GN2018 said:

Did you swap out the window before it even leaked?  If so, were you not able to order it that way?

 

Main question - how much did it cost?  I’m planning on waiting until I have a leak, but there are times when you do what you gotta do and I might just pay for it myself.  It’s hard to know, but a lot of this seems like a workmanship issue in both the original install and then the subsequent fix that seems often to not work.

I did the swap all on my own. Never gave the window a chance to leak. With getting a cap I wasn’t dealing with moving that to deal with the window. The glass guy had a good reputation and not a scratch or sealant mark anywhere. I ordered my truck and you can’t delete the sliding window. It was close to $700 with a GM solid window. A few of the chain places can do it for under $500. I went with the local guy who does most of the car dealers so he had the experience. 

  • Thanks 1
Posted

Wow, quite the sacrifice.  I don’t use my sliding window, but I thought if I had a cap I would actually use it then.  Thanks for the info.  I’d pay $700 not to have to deal with the leak even though I’d be upset with GM.  Still better than the aggravation.

Posted
5 hours ago, SigPig94 said:

This is precisely what I thought...to the point where i have already been contacting local auto glass shops.  A couple have actually told me they “won’t touch” my issue because it’s a brand new vehicle and still in the warranty period......????.......why exactly an after-market shop would care about that is beyond me......I, the owner, assume all responsibility for what’s done to my truck so add that to my list of things to scratch my head over.  
I’m gonna see how the replacement slider process goes in a few days at the dealership .......but I will DEFINITELY continue looking for a local window shop that I feel can fix this specific issue forever with a one-piece, non -slider installation.....I honestly feel that’s the only thing that’s gonna work.  Hope I’m wrong.

The place I used thought it was extreme and suggested just resealing the slider early on. He does work with a local GMC dealer and got a solid factory window from them. In the end he said it’s your money and was confident in his work on a truck with under 300 miles. I think most shops are intimidated by removing the interior trim pieces and seat back. 

Posted
25 minutes ago, GN2018 said:

Wow, quite the sacrifice.  I don’t use my sliding window, but I thought if I had a cap I would actually use it then.  Thanks for the info.  I’d pay $700 not to have to deal with the leak even though I’d be upset with GM.  Still better than the aggravation.

With the time of removing the cap and reinstalling it. Plus the wait time of getting into the dealer. Dealers glass guy is careless. It all added up to time is money. In addition to knowing the reputation of the guy I used help with the choice.  

Posted
Mine either

Sent from my SM-A505U using Tapatalk

Might make a great train horn button if you go solid rear window. Just saying,.... [emoji38]

Sent from my SM-N960U using Tapatalk

  • Like 1
  • Thanks 1
Posted
On 3/23/2021 at 9:27 AM, lebag335 said:

What did you get in its place?

2020 F250

  • Like 1
Posted

I think those that have had it actually fixed you can see a clear difference in the way certain dealerships attack this problem. Most who have had a second hand glass company come and perform this fix have had good success which is no shocker here. Some dealerships have techs that care about the work they do, and some clearly are just collecting a paycheck and doing the bare minimal.

 

That guy a few pages back with what looks to me to be bathroom sealant white goop, is clear that it was done at a piss poor dealership service department. I think the people who just said f it and bought a non slider glass window are the smart ones here, time is money and going back to the dealership 3 times for this issue is not worth the hassle, 500-700 dollars is short money to get a non leaking truck imo. And yes i think gm should be fixing this issue but clearly now a year away from a major redesign that is never going to happen.

Posted
I think those that have had it actually fixed you can see a clear difference in the way certain dealerships attack this problem. Most who have had a second hand glass company come and perform this fix have had good success which is no shocker here. Some dealerships have techs that care about the work they do, and some clearly are just collecting a paycheck and doing the bare minimal.

 

That guy a few pages back with what looks to me to be bathroom sealant white goop, is clear that it was done at a piss poor dealership service department. I think the people who just said f it and bought a non slider glass window are the smart ones here, time is money and going back to the dealership 3 times for this issue is not worth the hassle, 500-700 dollars is short money to get a non leaking truck imo. And yes i think gm should be fixing this issue but clearly now a year away from a major redesign that is never going to happen.

It's not a major redesign. That's not how GM operates. It's a mild refresh, most likely just the front bumper and grille. Everybody hoping for a magic rear window fix will likely be disappointed. We should all be sure to be inviting and welcoming when the 22+ trucks start posting about their leaky rear window.

 

Sent from my SM-N960U using Tapatalk

 

 

 

Posted (edited)

Add me to the list. 18k miles.  Sealant attempted.  Failed.   Going back in for new window.  Mexico truck for anyone still tallying the results.

 

What i find hysterical is that they did a multi point inspection and did not provide me with results as stated on the document.

 

 

truck.jpg

truck1.jpg

Edited by jeepincbum11
Posted
On 11/29/2018 at 8:13 PM, JKD said:

Update: Has been 18 days at the dealership and still not fixed. Removed and resealed the rear window only to find out today that the whole window needs to be replaced now because it’s leaking at the sliding window top rail even though it was confirmed by the dealer that the window seal itself was leaking due to poor job by factory in applying sealant. May be another two weeks to get the window from the factory. Then they have to take the windshield out in order to replace the headliner. Doubt I buy another GM after this one. Don’t what I’d get into because it seems automotive quality is degrading to the level of the 1980’s again. 

Hello sir. I wanted to check in and see long term what ended up happening with your window. I just bought a 2020 GMC and it’s already leaking. I am trying to find out if anyone has had any luck with fixing this issue long term. Thanks!

Posted

My 2019 Chevy RST with 24k back window started leaking last week. I called dealer and scheduled an appointment for this past Wednesday. The dealer had a window leak company do the work. I got the truck back the same day and you can't even tell they worked on it. No scratches, marks or sealant anywhere. It has rained the last two days and no leaks. Hopefully it's fixed permanently, but only time will tell.

 

 

Posted
My 2019 Chevy RST with 24k back window started leaking last week. I called dealer and scheduled an appointment for this past Wednesday. The dealer had a window leak company do the work. I got the truck back the same day and you can't even tell they worked on it. No scratches, marks or sealant anywhere. It has rained the last two days and no leaks. Hopefully it's fixed permanently, but only time will tell.
 
 

My 19 AT4 goes in this Friday. I can only hope for that level of service. Fingers crossed.


Sent from my iPad using Tapatalk
Posted
8 hours ago, Raymond378 said:

My 2019 Chevy RST with 24k back window started leaking last week. I called dealer and scheduled an appointment for this past Wednesday. The dealer had a window leak company do the work. I got the truck back the same day and you can't even tell they worked on it. No scratches, marks or sealant anywhere. It has rained the last two days and no leaks. Hopefully it's fixed permanently, but only time will tell.

 

 

On the quality of the work do you know if it was a small mom and pop place or a chain place doing the work? I believe the odds increase if it’s a mom and pop place doing the work. Even if the slider does leak again just the fact of no scratches, marks, sealant anywhere shows quality work. 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Latest Articles

  • Posts

    • I have a 2000 Silverado 1500 LS, whenever I put it into reverse and also in drive it clunks, the truck also feels sluggish when driving. Any advice/ideas ?
    • Looks like it's riveted to me. What is wrong with that 1? Welcome to the Forum!
    • Missing pieces of the Assembly   Detergency vs Solvency   Not the same thing. Detergency is the mechanism that surrounds solid particulates preventing amalgamation. Usually accompanied by a Dispersant whose job it is to keep those encapsulated particles in Suspension. Solvency keeps things that can be dissolved in solution.    Salt is a solid that can be dissolved. Pepper is a solid that cannot be dissolved. A detergent/dispersant is effective on pepper but a solvent is more effective on salt. As long as the solids remain in either state, dissolved or dispersed then they can be be removed with the oil upon change.    How many wranglers does it take to herd cats? Depends on how many cats your herding. How much sponge does it take to soak up water? How much water is there to soak up? Point is most oil blends start with some herding ability and next to zero sponge and recently even fewer wranglers are being sent to do the same job.    So you start with a dozen cowboys and zero cows but at the drive progresses you pick up cows along the way, but not cowboys. At some point you have more cows that the wranglers can handle and some leave the herd. Deposits. And the API has an acceptable number of cows they are willing to let loose. In the ideal world zero is the right number for he rancher but to the butcher....a few lost is fine. This cow is beat to death. Let's move on....   Solvency isn't something oils on the Walmart shelf care about AT ALL. Problem is, you motor does. Fuels driven varnish sticks rings and only a solvent can keep them in check. The bet is that the solids driven portion that plug the expander rings and the oil drain backs and VVT screens and AFM screens will be an issue long before varnish is. Not that it wont be but if they market well enough the consumer can be kept ignorant enough to either believe it is "normal" (A quart in 1 or 2K is normal) OR is kept at bay longer than the first owner is likely to hang on to the unit. Solvency cost money.    Now the OEM's have John Q. Public buffaloed into the belief that the number cows accumulated along the trail is a known and predictable CONSTANT. It isn't. Nor is the rate at which they crossed paths with them. Only the number of wrangles is constant. Or was. Each new generation of oil sees fewer and fewer of them.    So what happens when the number of cowboys is lower (lower TBN) with each seasons trail but the trial is longer (OCI) and the number of cows along that trail continues increase? (Conditions that promote deposits).    For awhile the blenders were on to something. Better bases are harder to degrade (fewer cows) but that was overtaken by a longer trail (OCI) and improved breeding (More cows) while continuing to reduce the cowboy staffing levels (TBN/Aniline #).    Marketing has been successful. We've fired most of the staff, cows breed line bunnies, the trail is ten times longer and we've convinced the boss his ranch is in better shape that it ever was.    That kids is just the cleaning side. The side few pay attention to.     
    • Mann+Hummel since 1941 per their web site 
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...