Jump to content

Anyone start tearing down a 2019 to install sound system?

WhineyTTwins
 Share

Recommended Posts

TNAT4 Enthusiast

TNAT4

Posted
Posted
31 minutes ago, LA_33 said:

I guess I talked to soon about mine working perfect. Been working perfect for over a week. Hours of run time and this afternoon the volume dropped pretty low and it had a staticky signal. It was in and out on the 15 min drive. Hope they will replace mine also. 

Well I hope the new device fixes the issue, I’ll let you know 

  • Replies 635
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

Chris walker
Chris walker

I fiber glassed my own enclosure for the AT4. I learned a lot of useful information if anyone else decides to glass a box in the new series of trucks. I've included a list of materials, goals, lessons

Chris walker
Chris walker

Ron,   You are correct. The Bose amp is behind the rear seat and that is where you will connect for the AT4 and the Denali. The non Bose system connection is at the firewall (you will not us

MadCaddie
MadCaddie

The Bose system does not sound good in the 2019s.  For the average listner they will be fine I guess but definitely not what I'd call good.  Not that any bose system is great persay but it's disappoin

Posted Images

LA_33 Enthusiast

LA_33

Posted
Posted
31 minutes ago, TNAT4 said:

Well I hope the new device fixes the issue, I’ll let you know 

Thank you. Hope it works!

disneybaker Enthusiast

disneybaker

Posted
Posted
My installer put the tweeters in factory location in dash. 

I was thinking going that route with component 6.5 in door and tweet in dash have same setup in my burb


Sent from my iPhone using Tapatalk
  • Like 1
disneybaker Enthusiast

disneybaker

Posted
Posted
Anyone throw in a kenwood powered subwoofer under the back seats or under the center jump instead of the kicker upgrade?

I like the kicker upgrade yeah it was expensive but I feel you are paying for plug and play,


Sent from my iPhone using Tapatalk
PabloK Enthusiast

PabloK

Posted
Posted

Here's my build... starts June 1st!

 

Front doors

-C7-100ct

-C7-350cm

-C7-650cw

-Audiocontrol 6.1200 DSP

 

Rears

-C5-650x

-Audiocontroll 4.300

 

everything else

-JL StealthBox 2 12TWB

-XD600/1v2

-large amounts of door soundproofing

-AmpPRO4 GM Interface1

-AmpPRO4 Fiber Optic Output

-Audiocontrol ac-bt24 Bluetooth adap

-JL Bass knob

  • Like 1
lilsullivan04 Enthusiast

lilsullivan04

Posted
Posted
13 hours ago, PabloK said:

Here's my build... starts June 1st!

 

Front doors

-C7-100ct

-C7-350cm

-C7-650cw

-Audiocontrol 6.1200 DSP

 

Rears

-C5-650x

-Audiocontroll 4.300

 

everything else

-JL StealthBox 2 12TWB

-XD600/1v2

-large amounts of door soundproofing

-AmpPRO4 GM Interface1

-AmpPRO4 Fiber Optic Output

-Audiocontrol ac-bt24 Bluetooth adap

-JL Bass knob

Didn’t think the AmpPRO4 interface didn’t work with the 2019 GMC Sierra/Chevy Silverado?

TNAT4 Enthusiast

TNAT4

Posted
Posted
On 5/11/2020 at 9:46 PM, LA_33 said:

Thank you. Hope it works!

Well I have the new NAVTV Zen unit in and traded one problem for another.  It’s only dropped the volume once in several days, but still occasionally has the staticky noise that resolves with a reboot.  The new problem is a loud popping noise occasionally and when I turn the volume up or down rapidly.  Sounds like a bad speaker connection but I’ve checked everything and it never did this until I put in the new Zen.  I made sure I have the newest software.  Very frustrating, appreciate any advice you guys can offer.  

lilsullivan04 Enthusiast

lilsullivan04

Posted
Posted
3 hours ago, TNAT4 said:

Well I have the new NAVTV Zen unit in and traded one problem for another.  It’s only dropped the volume once in several days, but still occasionally has the staticky noise that resolves with a reboot.  The new problem is a loud popping noise occasionally and when I turn the volume up or down rapidly.  Sounds like a bad speaker connection but I’ve checked everything and it never did this until I put in the new Zen.  I made sure I have the newest software.  Very frustrating, appreciate any advice you guys can offer.  

 

Did you remove the Bose amplifier? Or completely disconnect it?

TNAT4 Enthusiast

TNAT4

Posted
Posted
49 minutes ago, lilsullivan04 said:

Did you remove the Bose amplifier? Or completely disconnect it?

Removed it 

TNAT4 Enthusiast

TNAT4

Posted
Posted
32 minutes ago, lilsullivan04 said:

Hmm that’s odd have you contacted NAV-TV? I’m actually saving to buy the Zen interface right now.

Yes they’re working with me.  This is the replacement unit because the first constantly dropped the sound and only a reset would correct it.  That’s a known problem with the early units but this new one should be working properly.  

lilsullivan04 Enthusiast

lilsullivan04

Posted
Posted
8 hours ago, TNAT4 said:

Yes they’re working with me.  This is the replacement unit because the first constantly dropped the sound and only a reset would correct it.  That’s a known problem with the early units but this new one should be working properly.  

That’s good they are working with you and when I buy mine hopefully I get the newer unit. When did you first buy yours?

TNAT4 Enthusiast

TNAT4

Posted
Posted
1 hour ago, lilsullivan04 said:

That’s good they are working with you and when I buy mine hopefully I get the newer unit. When did you first buy yours?

I bought it in February.  I’m going to take the seat off again today and take another look at all the connections but I didn’t see any problems when I looked the other day.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • KARNUT
      Joke Thread

      By KARNUT · Posted

      It took me a minute, but I got it.😆
    • Sdid
      2020 Silverado 1500 8speed gm needs to recall transmission

      By Sdid · Posted

      I have A 2020 1500 5.3 8 speed. LTZ. Transmission problems since 60,000 miles. Started when I go to store in morning to get my morning coffee before work leave truck running get back in put it in drive/ rev no movement step on gas a little slams into gear. Put in neutral step on gas little shake then put in gear and gose.  Shut truck off start .. ok now at stop light stop truck after a few seconds feel a little kick if that doesn’t happen stuck in 3/4 gear shut truck off wait few seconds and start usually ok again. If you down shift manually ok as long as you get into 1st before stop. If not it kicks . I WANT A NEW TRANSMISSION. Now I want a new truck it just hit 80,000 IDK IF ILL BUY CHEVY CAUSE THEY STILL HAVE THE PROBLEM AND REFUSE TO RECALL . Oh I’ve changed the fluid and filter 3 times now. And yes used mobile 1 not ac/delco cause it’s not meeting the requirements that mobile is did use ac/delco filter 
    • Chuck FB
      Joke Thread

      By Chuck FB · Posted

      Of course refrain from political debate but I myself have very dismal hope for what is all going on up here every where we turn so I nodded my head when I saw this joke.     
    • diyer2
      Navigating senior years.

      By diyer2 · Posted

      I'm looking at carpal tunnel surgery on my left hand and lumbar fusion. 
    • Atlas
      Wow I'm in a pickle. (Broke down truck) and a story.

      By Atlas · Posted

      While waiting for parts I have been working on installing the AC compressor, new accumulator, and orifice tube. Also changed out the high side ball valve (original). The orifice tube that was in there wasn't too bad. Slightly dirty, a little bit of junk, but not blocked. Glad I changed it out.   The accumulator, which should have been a 5 minute job, may have just burned $50. Put some PAG in it, wrote the date and mileage on the side, fresh o-rings and gooey'd up the threads and rings with Nylog. Got everything connected and snugged and was going to vacuum down the system, and....   My manifold gauge won't fit on the port. It's not an R12 service port. It LOOKS like an R134 service port but the diameter is a hair too large. There's a sticker on the accumulator that says it's designed to be used with R12 and R134a systems only. So it's not R1234yf. Even if I reduced the diameter slightly with a file, the shoulder on the port is too large so the quick-connect valve won't lock on. I'm stumped. It's going back, and 50/50 on if they'll give me a refund.   Also, I did a fuel pressure test.... Key on, the gauge spikes to about 60psi and quickly bleeds off, like 2psi per second. The fuel isn't going into the plenum, no smell, starts fine, so I'm guessing there's a bad check valve in the pump and the fuel is just draining back into the tank. oh, hell. But, it shouldn't be a problem, pump primes just fine and the truck starts right up. It just means I can't really ever use fuel pressure to verify a leak at the injector or intake.

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...