Jump to content

Infotainment Screen Black When Using Remote Start

smiles
 Share

Recommended Posts

Smsafety1 New Member

Smsafety1

Posted
Posted

I just bought my truck last week and I am having the same issue.  Did you get yours fixed?  What was the solution?  I am also having a dead battery if I let it sit for 2 days did you have that issue?

  • Replies 57
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

MJK
MJK

There is a recent update for this issue.

T.han90 Enthusiast

T.han90

Posted
Posted

Any update on this from any of you about the solution? My 2020 Silverado under 4K miles just started doing this today. If I remote start the screen will stay black but if I just use regular push to start it comes on.... calling dealer tomorrow to see if they know of it. Also mine says no update 

T.han90 Enthusiast

T.han90

Posted
Posted
25 minutes ago, Smsafety1 said:

I just bought my truck last week and I am having the same issue.  Did you get yours fixed?  What was the solution?  I am also having a dead battery if I let it sit for 2 days did you have that issue?

Let me know what you hear from your dealer I’m afraid to even let mine sit over night now it just started for me today after a trip to the store

Smsafety1 New Member

Smsafety1

Posted
Posted
2 minutes ago, T.han90 said:

Let me know what you hear from your dealer I’m afraid to even let mine sit over night now it just started for me today after a trip to the store

Will do.  I see several people saying it’s a battery issue. Hope that’s all it is 

MJK Enthusiast

MJK

Posted
Posted
1 hour ago, Smsafety1 said:

Will do.  I see several people saying it’s a battery issue. Hope that’s all it is 

 

T.han90 Enthusiast

T.han90

Posted
Posted
18 hours ago, Smsafety1 said:

Will do.  I see several people saying it’s a battery issue. Hope that’s all it is 

Thinking that’s what it is noticed on star is disabled too and auto stop works less. I have app Saturday morning let’s see what they say 

shadow gray 2020 hd Enthusiast

shadow gray 2020 hd

Posted
Posted
On 2/12/2020 at 12:21 PM, smiles said:

I have to park the vehicle, turn it off, and then re-start using the vehicles start button to bring the display back on. Anybody else having this issue?

About 1100 some odd miles on mine now and have not had this issue when remote starting.(knock on wood)  I am having almost every time I get in though where it is asking me to confirm which user profile.  

T.han90 Enthusiast

T.han90

Posted
Posted
18 minutes ago, Trtmntdude said:

Took mine in and they replaced the battery. Problem solved.

Guess that’s what I’ll be getting Saturday morning when I go to dealer

Biker90 New Member

Biker90

Posted
Posted

I had this blank screen issue on my 20 rst, I removed both infotainment fuses and put them back in, haven't had the issue since.

T.han90 Enthusiast

T.han90

Posted
Posted

Auto stop has quit working today and noticed truck took a little more hmph to start today thinking it’s a battery for sure which sucks and weird for only being 3 months off lot 

MJK Enthusiast

MJK

Posted
Posted

My 2020 2500HD with 500 miles is in the shop today with the blank screen on remote start, dead batteries yesterday and several other wired things. Like gauge clusters bouncing and info screen behind steering wheel coming on after truck was turned off. Will let y’all know what this shop says.

T.han90 Enthusiast

T.han90

Posted
Posted
6 hours ago, MJK said:

My 2020 2500HD with 500 miles is in the shop today with the blank screen on remote start, dead batteries yesterday and several other wired things. Like gauge clusters bouncing and info screen behind steering wheel coming on after truck was turned off. Will let y’all know what this shop says.

Let me know what they say because All of the above is what mine is doing plus auto stop has stopped working too 

Stand By Enthusiast

Stand By

Posted
Posted (edited)

Having read these complaints all summer, though not really experiencing anything myself yet, I just thought of an issue we went through with a ford. I just went out an looked and it looks like both the engine ground and battery ground attached at the firewall, may be attached to a painted surface. We had a new 2011 fiesta and after a couple months at start up, the gauges would go nuts and it wouldn't start. Left her stranded a few times. Having dealt with with weird guage activity with an earlier grand cherokee, I figured it would probably be battery related. I went online and found ignition switch recalls and tech bulletins on the fiesta line for the instrument panel acting up and potential dash fires. The tech bulletin that seemed to cure everything, said to scrape away the excessive paint at the engine bay ground attachment points. I took a look and ours were almost completely painted over. Scraped them off and never had another tissue. Taking a look at mine, without disconnecting yet, the actual screws don't look to be painted, but obviously the surface of the firewall they but against is. I have a custom, so fewer electronics to boot up at start up, so maybe that's why I haven't seen a problem yet. I do plan on adding upfitter switches and some other stuff soon and plan to disconnect the ground straps and clean off the surfaces to prevent problems. I also have a short cmutr, so I'm careful about letting it run a little longer after starting to keep the battery topped off. All the control modules new vehicles have, use a lot of juice when booting up, aside from the starter. And then there's the weird, hit the locks again, then hold the remote start button for 5 seconds for the vehicle to fire and fan blowing full blast, using up additional juice at start up.

Edited by Stand By

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • Atlas
      Wow I'm in a pickle. (Broke down truck) and a story.

      By Atlas · Posted

      Why don't I have a good scanner? I've always wanted one when I've needed one.   My latest reading says I don't need to do a relearn on the ckp sensor on a 1995 with OBD 1.5. The relearn is prescribed for the later-model 1995's which shipped with actual OBD II when GM completed the transition in prep for the 1996 MY. I need to confirm that. Did you know forums are disappearing? Knuckleheads on Facebook... it's not the same. It's just not.   So, scanners. Again, shooting myself in the foot for having eBayed my Snap On MT2500 "brick" with all the adapters. Not that I couldn't buy another but those are getting quite old, and mine wasn't new enough to work on 2000's vehicles.   Damn it (as I'm scanning my email between paragraphs here). Did you know there's a 2000 Jimmy 2-door on BaT that's ending this morning? It's local. I want it. 14k miles. Absolutely beautiful.   Back to scanners. MT2500's are old. Solus, now that could be a contender. There's a ~2008 Verus with a system error that's basically new in box for cheap. Hmm...I'm not sure about a scanner that runs an archaic version of windows (95 or CE, I can't tell).   I want the ability to reset and rotate TPMS, test individual modules, bleed ABS, electronic parking brake controls for servicing brakes, relearn procedures and other bidirectional controls.   Snap On does an MT2600. It's a new model as of last year, marketed as their "entry" scanner. Entry? Only where $1900 gets you through the doorway plus, I'm guessing, $1000/year if you wish to keep it current. So goes scan tools actually designed for production environments. Want decent products with excellent support, you pay for it.   Everyone is raving about Autels and TopDons and Foxconns and all these newer brands that are selling the $500 "prosumer" scanners for backyard hacks like me. They're tempting...honestly. Updates are cheaper, base prices are remarkably cheaper... And you get to deal with bugs and translation whoopsies and, well, just don't use it on anything expensive, OK? Having a dealer replace an ECU because it needs to be re-imaged after an adventure in scanning is no joke. But I think most people are getting by OK with these units.   eBay on a scratch-and-sniff pro-model oldie, a shiny new TopDon, or???   God dang it, I can't stop looking at this Jimmy. I'm ready! I'll Bring The TRailer! It's beautiful.
    • Texasdeere
      What have you done to your K2 today?

      By Texasdeere · Posted

      I removed the OE running boards.  It looked so much better.  I wish I took them off a long time ago.     I had to put something back on for my wife.  I wanted Westin Sure Grip Running Boards but they are very pricey, like $600 plus.  I was going to go with the Ionic 41's like I had on the 2019 Silverado but went with Westin Outlaw Drop Steps instead, about $200 cheaper.  They are sturdy and functional but not super crazy about the look, but it works.  
    • Atlas
      Gas Prices

      By Atlas · Posted

      It's all a crock of 💩
    • fondupot
      Disable DRL's

      By fondupot · Posted

      I had a Gen5DIY DRL relocate harness from a 2022 1500 that I saved. I had Gen5DIY modify the harness for my 2024 Silverado 2500. Plug n Play, worked perfectly.    Here's a video I made for the 2022 1500 truck. The install is more or less the same on a 2500.    The harness relocates the DRL tot he top amber turn signal on my 2500.     
    • CamGTP
      Gas Prices

      By CamGTP · Posted

      Can ask that about a lot of places.   Holiday sells 91 for $1 over 87 octane. BP 93 is 80 cents. Amoco 93 is 80 cents Kwik Trips is $1.20 for 92 or whatever they have and $1 for the 91.   I know that this is not exactly same as what you are saying with the premium to premium debate of those two stations but why is there such a difference. Top Tier this and that, it's all BS. All the fuel comes from the same damn refinery, so give me a break.

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...