Jump to content

Recommended Posts

Posted (edited)

 

Just out of curiousity, what is the u joint bolt torque specs?

They don't have an exact torque spec but more of a procedure. This is from my memory but you can find it somewhere on this site. I believe you torque them to 59 ft-lbs. After they are all at 59 ft-lbs you then turn each nut an additional 130 degrees. not sure if this is the exact procedure but it's something along these lines. I have mine at 78 ft-lbs and from where they were from the factory to 78 it took almost 3 full turns to get them there. It helps but didn't solve the issue by any means.

 

I just re-read your post, you're looking for the u-joint bolts on the drive line? Can you even get a torque wrench on them?

Edited by abominable z71
Posted

Any of you have 275/60R20 tires or larger? If so, what brand? Improvements to ride quality? I've been all over this forum and a couple others. Mostly curious.

Posted

Any of you have 275/60R20 tires or larger? If so, what brand? Improvements to ride quality? I've been all over this forum and a couple others. Mostly curious.

I have that size in an LT tire. My vibration went away after swapping from junk stock tires, and these ride a bit better even though they are an all terrain and they are LT rated not P rated

 

Sent from my SM-N900V using Tapatalk

Posted

Well as of now my 2015 All -Terrain is in for the shakes no bad but just enough to finally have the dealer look into it .3rd time I have commented about and have it documented on each visit , 1st time rebalance tires last year, 2nd time rotation and rebalance balance was out, finally this time they have it for 2 days so far balance is good next step they are connection the vibration test kit? with pile of sensors etc connected and driving it a round. have 35000 KM (Canada) 21000 Miles

also they are checking the lazy shifting of transmission at least to me it is. no matter the out come it is being traded in next spring. being for sale now and potential buyer have commented on the minor shake so as of now I can not even sell the thing !!

Plus seat belt recall and air bag recall done.

Up date Sept 19 truck was at the Dealer for 2 days they found no problems I may be crazy cause no one else feels it even my wife.

Best out come so far is listed it for sale Sept 05 before dealer visit and Sold pending mine and buyer schedule to work out. it will be gone by Sept 21. They felt no vibration at all on the test drive at highway speeds.

Posted

New poster here. I do have the same issue as well. I didnt notice it as much when I had the OEM 18' tires on. It got worse once I switched to 33s 12wide 20''rims OFF road tires. I did some tire balancing and then it didnt vibrate much in USA highways. However once abroad I do notice it when I go up hill or when Im doing off road. I do notice strong amounts of vibration when the pavement is not very well made. As If im about to lose control of the vehicle when im driving. My old Mazda 2001 truck piece of junk doesnt vibrate as much and its a diesel junk that vibrates on idle LOL. Im looking around the thread and cant find any solutions. Did anybody compile possible solutions or something to ease the vibration at least? Also this truck is no longer in the states. So Its impossible for me to take it to the dealer and get a fix.

Posted

Praying new tires help my ride. I aired up these good years stockers to 39 p si and seems take away the trembling that goes along with the Chevy shake. So considering trying an LT tire. And I'm still saving up to try new leaf pack for the rear.

Posted (edited)

Add me to the list of owners of a $50K vibrator. My 2015 High Country started vibrating at around 70MPH when it hit 9000 miles. I'm at 14K miles now and it is getting worse so I dropped it off yesterday. Received a call today saying the tech had confirmed the vibration exists and that the first step is a force balance at a cost of $230. I told them to go ahead and do it. The next step will be to look at the tires if this doesn't fix the issue.

 

 

What is really strange is that it doesn't always happen. I can be driving into work vibrating away at 70MPH, hit some traffic and slow down, get back up to speed and experience no vibration.

Edited by David_
Posted

Add me to the list of owners of a $50K vibrator. My 2015 High Country started vibrating at around 70MPH when it hit 9000 miles. I'm at 14K miles now and it is getting worse so I dropped it off yesterday. Received a call today saying the tech had confirmed the vibration exists and that the first step is a force balance at a cost of $230. I told them to go ahead and do it. The next step will be to look at the tires if this doesn't fix the issue.

 

 

What is really strange is that it doesn't always happen. I can be driving into work vibrating away at 70MPH, hit some traffic and slow down, get back up to speed and experience no vibration.

Not strange at all, been mentioned numerous times on this thread. I just hit 14k miles on my truck and the shaking has almost gone away. I might be one of the few whose truck got better with miles but it also points to my problems being mostly with the tires IMO.

Posted

Tell them to stick that 230 up their asses. It's under warranty.

 

Sent from my SM-G930R4 using Tapatalk

 

Exactly

Posted

According to them, GM does not warrant tire balance. They people at the dealer aren't being assholes about it but I will drop it right back off if it isn't fixed.

Posted

According to them, GM does not warrant tire balance. They people at the dealer aren't being assholes about it but I will drop it right back off if it isn't fixed.

Keep the receipt because it will feel great for a few days and slowly return. Get your money back when it does!

Posted

Yeah I believe GM covers the tires, from having to replace them or to rebalance them, up to 12k. My dealer ate the cost of rebalance at 34k, they are awesome

Posted

I don't see how they can charge you. I just had two replaced and all 4 road force balanced. Plus the front 2 re-road force balanced after I still was experiencing vibration. I left the dealership today and I'd say it's 98% fixed. I maybe just looking for it so much now that I don't know what fixed even means anymore. I swear I'm paranoid about the issue now, especially after reading this thread lol

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Latest Articles

  • Posts

    • Holy s**t - not much of a parts thrower you say? You BLASTED that thing with the parts cannon!  You'd have been probably $1,000 ahead if you had just brought it to a competent shop rather than shotgunning a bunch of parts it clearly didn't need.   Just FYI - oil additives are really, REALLY good at ONE thing ... and that's emptying your wallet. They're ALL useless gimmicks.   If that has the L94 or L99, then #7 is an AFM cylinder. I'd suspect a failed lifter in that case.   If you leaned on wiring, sensors, and/or connectors while changing the oil, you'll have to check all that to be sure pins didn't get pulled out, connectors broken, etc.. Old wire loom that was barely adequate when new is certainly brittle by year 19 - make sure wires aren't chaffed and shorting out somewhere where you might have leaned. or supported yourself on it.   If your a mechanic, why didn't you just find out what you were missing and troubleshoot from there??  TIMED spark, fuel PSI / injector pulse, air, compression.  Can't make ANY money going the parts cannon route.
    • LOL! Are you joking?? That wax SUCKS! 100% gimmick made to "look" good.    After just TWO winters I had severe surface rusting in patches over 90% of the frame. Only reason it looks great in the pics is because I SATURATED the frame every single fall with used motor oil for 14 of the 16 years I owned it. Otherwise it would've been sent to the crusher 8 years earlier with the speed it was rusting prior!    I sold that POS 3 years ago. Was a gigantic headache the second it rolled off the showroom floor. Brakes pulsated on the TEST DRIVE. Door trim fell off the 1st week! Interior squeaked and rattled, and the drivetrain clunked after 2k miles. 4x4 switch failed shortly after. Front end - ball joints, struts, hub bearings - all failed between 38k-50k. Engine started burning oil at 50k. Rear and and transmission failed before 100k. Nothing but problems, and frustration with the piss-poor engineering designed to make you give up. Well, it worked! Nothing on that truck was easy to remove ... except the wheels. They haven't figured out how to screw that up yet. Give 'em time ...   I won't make that mistake again. EVER.   Such fond memories ... https://postimg.cc/K1qf23tS  https://postimg.cc/gallery/X02z64J  https://postimg.cc/gallery/mHSRXZv  https://postimg.cc/gallery/D4mMRfL
    • Different monitors do their test only under conditions specific to that monitor.  you MIGHT find the drive cycle conditions for the monitor that isn't ready on this site: https://lemon-manuals.la/   If it's not there, then it should be on alldata.com for your truck, but it requires a paid subscription.   And you need to know which specific monitor isn't ready.
    • from another thread   Update...although the truck sometimes seems to idle weird and the transmission shift a little weird, I've driven about 7,000  miles and no issues.   However, the way GM has handled my rental reimbursement, the situation when my truck quit, and the recall in general has led me to this point...I have driven a GM vehicle for the past 46 years and unless I buy a C3 Corvette, this is the last GM vehicle I will ever own. 
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...