Jump to content

Recommended Posts

Posted

I recently replaced mine with one I bought off Ebay. part number 85585333. My trucks the 6 speed. I had called local dealer but he wanted over $40 more than an online Chevy dealer so I opted to not buy local.( I always try to buy local). Anyways, my drive to town for breakfast prior to swapping in the new tbv, temps were right at 194-195. After swapping in the new tbv temps were right at 153-154. Truck only has 16k on it and never had the shakes but after reading this thread from start to finish over the past 7 years, I feel good getting this done. It was a simple job, anyone with minimal mechanical skills could probably do this with ease. Next up, swapping in some new fluid.

  • Like 1
  • 1 month later...
Posted

Hey guys, so I have a 2023 Sierra SLE 1500. I only put 11000kms before experienced the vibration/shaking. I thought my transmission was faulty. WOT was smooth af, so I was super confused why the transmission would do this at low RPMs. If this helps anyone I read the U bolts could be the culprit. I had been riding around with 200lbs of sand in the bed for the last 2 months and thought it may be putting too much weight on the U bolts if they are loose. I took out the sand and the vibration is mostly gone. Very slight if anything which I think I felt even when it was new. I am going to take the truck into the dealership to get those looked at and see if they need to be tightened. Would do it myself but I don’t have any tools. Hope that helps as it solved my problem 90%. 
P.S I had a 2021 gmc Sierra sle 1500 aswell after I put sand in the bed, I got the same vibration thinking the tranny was bad. Never connected the dots with this one until I removed it. That truck still left me stranded lol due to a not starting issue multiple times before I auctioned it off. I had replaced the starter on that and it left me stranded again with the same problem lol. 

Posted

I took my brand new truck to the dealership and they said they had to slightly tighten the U bolts to spec. Nothing too bad. But the vibration is totally gone and the transmission doesn’t feel like it’s gonna fall apart. It’s driving like it’s brand new for the whole last week. I think the extra weight in the bed and loose u bolts were the problem. 

Posted
On 8/5/2013 at 5:49 PM, Silver space ship said:

So I got it back from the dealer today and was told they test drove one from the lot and it had the same vibration and possibly even worse then mine. I was told GM admits there is a problem but at this time no solution. I was told to wait until there's a solution or the problem progresses.

It’s the same Transmission torque converter problem they have had for years. I have a 2018 low mileage with the same problem. New or rebuilt transmission is the only solution. GMC has let us down 

  • 3 months later...
Posted (edited)
On 9/29/2023 at 12:19 PM, Ron Cooley said:

It’s the same Transmission torque converter problem they have had for years. I have a 2018 low mileage with the same problem. New or rebuilt transmission is the only solution. GMC has let us down 

Ron, new member here. I’m not sure it is the torque converter. Just had my transmission and torque converter replaced on my 2014 Sierra 1500 SLT 4x4. I still get vibration from around 50 mph to about 75. It gets worse when I apply the brakes. Just had rotors replaced and wheels balanced. Still vibrating! The truck has 143k miles and this problem has only shown up since about 100k miles.

 

had a similar problem a few years back when the truck would shake badly from about 35 MPH and above. I was told it was the driveshaft so I took it to a mechanic in Atlanta who builds drives shafts for NASCAR. He worked on it for about half a day and then reinstalled it. Still vibrated! I took it to the GM dealer in Kennesaw, Georgia where I bought it and they had their transmission shop look at it. Of course, they said I needed a new transmission and torque converter at a cost of $6000. I passed on that and took it to AAMCO transmissions on Cobb Parkway in Atlanta and they fixed it in less than 30 minutes. It only needed transmission fluid! So I’m not real motivated by taking it back to a dealer. 
 

has anyone found what the actual cause is and how to fix it?

 

Any suggestions would be greatly appreciated!

Edited by FedUpwGM
Posted
19 hours ago, FedUpwGM said:

Ron, new member here. I’m not sure it is the torque converter. Just had my transmission and torque converter replaced on my 2014 Sierra 1500 SLT 4x4. I still get vibration from around 50 mph to about 75. It gets worse when I apply the brakes. Just had rotors replaced and wheels balanced. Still vibrating! The truck has 143k miles and this problem has only shown up since about 100k miles.

 

had a similar problem a few years back when the truck would shake badly from about 35 MPH and above. I was told it was the driveshaft so I took it to a mechanic in Atlanta who builds drives shafts for NASCAR. He worked on it for about half a day and then reinstalled it. Still vibrated! I took it to the GM dealer in Kennesaw, Georgia where I bought it and they had their transmission shop look at it. Of course, they said I needed a new transmission and torque converter at a cost of $6000. I passed on that and took it to AAMCO transmissions on Cobb Parkway in Atlanta and they fixed it in less than 30 minutes. It only needed transmission fluid! So I’m not real motivated by taking it back to a dealer. 
 

has anyone found what the actual cause is and how to fix it?

 

Any suggestions would be greatly appreciated!

 

I have no doubt GM knows what the cause of the shake is, but they aren't talking. Not talking because the fix is likely both involved and expensive. 

 

Sorry but I have no suggestions on how to fix the shake.

Posted (edited)
On 12/31/2023 at 12:12 PM, Willyone said:

 

I have no doubt GM knows what the cause of the shake is, but they aren't talking. Not talking because the fix is likely both involved and expensive. 

 

Sorry but I have no suggestions on how to fix the shake.

See here:
https://www.tsbsearch.com/Chevrolet/21-NA-199

Chevrolet TSB 21-NA-199.pdf

Edited by MikeBMW
Posted

I joined the forum just to post my resolution to the vibration issue.
Background:
2015 Yukon XL 4WD with a 5.3 and 6 speed transmission. 167k miles. The truck would violently vibrate over 75mph to a point of it being scary.
Vehicle was religiously maintained at the GMC dealer its entire life with regular fluid changes and maintenance.
Issue:
As to the vibration, I have tried every solution in the 857 pages of this thread including new tires, balancing, new trans cooler and lines in the TSB above, flushed transmission several times, new filters, etc and nothing worked.
Solution:
In the end, a reman transmission from GM installed at the dealer solved all vibration issues.
GM = trash.

  • Like 1
  • 3 weeks later...
Posted (edited)

I installed some 2 degree pinion angle shims (fat side facing front) and the wobble/ vibe is 80% gone. I also tried the spring clamp and found with the clamp on the front side of the leaf spring. After the truck rode like a Cadillac, so I'll pickup the Deaver mini pack and shim the pinion accordingly. I feel like the leaf springs twist which is the reason it is worse with 20s. after i got 18s the wobble lightened up.

Edited by Snowcamo
  • Like 1
Posted (edited)

Here is what's going on with the drive train in alot of our trucks.  It may not be the resolve for all, but I am sure just about everyone can relate.  Let me know what you guys think. 

 

 

 

 

Edited by Snowcamo
  • 5 months later...
Posted

Hello everyone, I'm new to the forum. I recently got a 2018 Silverado 5.3 AWD with around 107k miles. Now for my problem. When I start off, I feel a jolt/vibration on the front left for around 1 second. If I start off very gently, I can't feel it. The first thing I did was adjust the track. But the problem is still there. I looked at the axle and suspension on the ramp and couldn't find anything there. You can't feel the jolt from the outside either. Noises aren't audible from the outside either. It's loudest as a driver, as it's also transmitted through the steering wheel. I suspect the left engine mount. During the test, the engine tilted slightly, what do you think? Does anyone know the problem? Thanks.

  • 1 month later...
Posted

My husband is a master mechanic & he can't fix this problem! He has put a new transmission in. He's tried 4 new torque converters. He has flushed and changed the fluid a million times. Tried all the stuff that could go in it & NOTHING WORKS!!! We bought this truck used from a dealership but they were aware of this problem. It can not be fixed & the dealership will not do anything about the problem if it's over 100k. We paid over $25k for this truck with over 200k miles but Chevy trucks usually run for more than 350k miles & still are strong if we'll taken care of. This is a problem & needs to be addressed!!!

Posted (edited)

Goggle chevy shake... search this site for it as well. Best of wishes to you all. I'm really thinking of swapping frames at this point. May as well get a new truck then. Idk.

 

There is no legit one fix all to this issue.

Edited by Snowcamo
Posted
15 hours ago, Crystal 2024 said:

My husband is a master mechanic & he can't fix this problem! He has put a new transmission in. He's tried 4 new torque converters. He has flushed and changed the fluid a million times. Tried all the stuff that could go in it & NOTHING WORKS!!! We bought this truck used from a dealership but they were aware of this problem. It can not be fixed & the dealership will not do anything about the problem if it's over 100k. We paid over $25k for this truck with over 200k miles but Chevy trucks usually run for more than 350k miles & still are strong if we'll taken care of. This is a problem & needs to be addressed!!!

 

My take.... GM and their engineers know what the cause of the shake is but they're intentionally keeping the cause or causes to themselves. Likely the cost of correction is very pricey so GM has decided to evade the issue as best they can, it's cheaper to pay their lawyers. GM is intentionally sticking it up their customers asses. Same with the VVT issue. Expensive to fix so let the customer swing in the breeze.  FWIW my '16 Z71 with just under 50K miles has the vibration, and also appears to have the VVT issue, possible bad lifter on cyl no. 7. I'm 73 yrs old and retired and I can't really afford to buy a new truck at present. I've bought GM trucks most all of my adult life but when the time comes for my next truck, fk'm, it won't be a GM.

 

No doubt GM has folks that monitor this site and they probably get a kick out of the complaints. 

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Latest Articles

  • Posts

    • Hello hello looking forward to expanding my knowledge of the 2026 2500 HD that I just bought.   Truck has 3500 miles on it four-wheel-drive crew cab and I’m about to put a 6 1/2 inch BDS lift on it 18 x 10 -25 offset with 37’s   Already have the wheels and tires just waiting on the lift install in about three weeks   Question what surprises am I not gonna be happy with?  I’m not new to lifted trucks so I know that acceleration towing gas mileage all that is affected..   Question is those of you that have this truck this powertrain with a 10 speed Allison and have done the mods that I’m doing,,, how bad is it? Is that Allison constantly gonna be hunting for the right gear to go into? And what about towing, acceleration, fuel consumption as mentioned?    Lastly how come I can’t find any ring pinion gear set up for these axles and when could I expect to see them?   I apologize if there’s any typos I’m doing speech to text on my iPhone.    
    • I've got a 2013 2500 6.0L Flexfuel. Drove the truck earlier today with no issues. Went to run an errand tonight and noticed key fob wouldn't work. Figured battery was dead, so replaced fob batter. Still wasn't working. Grabbed my other set of keys with the other fob and that one wasn't working either. So I manually unlock truck and insert key. Interior lights come on, dashboard lights up, turn key and truck starts. Turn truck off, like a moron, and try starting again. This time no crank, no click, no nothing. Lights still come on and dash lights up, but now I'm getting a service 4wheel drive, service tire monitor, etc. Check voltage on battery and Im showing 12.2v. Throw my battery charger on it and give it 15 mins and try starting again. But still no crank no start. Decide maybe its a bad battery, run to autozone grab a new one and put it in. Same issue. Disconnect battery and let it sit for 15 mins. Try again and still nothing. I had managed to roll the windows down earlier as its a humid night, but now I can't get them to roll up. Power locks are also not working now. Then randomly I try the key again, and it fires right up. Immediately I roll up the windows as we have nothing but rain forecast this week. I shut it back off wait 30 seconds and start up again. Worked a 2nd time. So turn it off, start putting things back together. Try one more time, and back to no crank no start. And now the car alarm starts going off. Had to disconnect battery and leave it that way for the night as I don't think my neighbors would appreciate my alarm going off again tonight. Any thoughts or help would be appreciated. 
    • No one will care for you like you care for you. Do what you can for as long as you can. IMHO of course. 
    • How about them NICKS!!! 
    • Hi there.  Long time lurker, first post.    i have read the previous posts regarding the water ingress problem with this emblem.  I bought my 1500 SLT the  summer of 2025 new and after reading the MANY problems with these emblems failing I decided to install one anyways.  As per a YouTube video, I sealed ( or tried to) this sign with silicone sealant around the outer perimeter joint and the holes that were already somewhat sealed on the rear plate of the emblem.  And installed the connector assembly using dielectric grease on the connectors. The installation looked great and worked well for about 4 months……then FAILURE.  Grrrrrr…… I live in the great white north and wash my truck weekly in an automatic car wash  to keep the salt off.  Let me tell you that removing the old, failed emblem is a whole different animal than removing the OEM individual letters without removing the grill assembly. Mainly because the illuminated logo is built differently than the original letters which  you can remove the red surface lettering with a knife or some kind of blade which gives access to the tabs which hold the logo onto the grill. So I had to essentially destroyed the old emblem to remove it. Doing so killed my chance of doing somekind of autopsy on the failed , old logo.  But there was plenty of water inside when I ripped it apart.  Prior to installing the new assembly I tried it with the old harness and it works fine.   Does anyone have any insight as to where the water is getting into this emblem? I intend to seal the new logo with slow curing epoxy this time around using a syringe.  I think this newer emblem may be an updated unit which I hope GM got the vendor to fix. It has an October 2025 date on it.    If this one  fails,  I am just going to revert back to the non-illuminated letters….AFTER PULLING THE GRILL.    Any thoughts on sealing with epoxy would be appreciated. Thx!   Doug  
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...