What have you done to your K2 today?

Ravenkeeper · February 23, 2020

On 2/18/2020 at 9:50 PM, Ravenkeeper said:

Rerouted the Illuminated Bow Tie harness on my truck this morning, before going to work. I didn't like the way I ran it when I installed it a few weeks ago. When I tore it apart, I found out that I had to do some wire repair, too, both the white and the black wire had chaffed a little. I originally had the union between the two halves "clipped" to the truck frame, and later decided that if anyone takes off the grill and didn't realize it was done that way, they could easily damage either the light or the connector. Found a video, this last weekend, while I was sick , that ran the main part of the harness along the same route with the hood release. Took photos of the original route and the new route, will post them when I get home from work tonight, or before I go to work tomorrow afternoon.

Originally drilled the 3/8" hole dead-center, but had to work it down/left to line it up correctly.

Original path that I ran the harness:

Zip tied the two wires to the "struts" just left of center:

Rerouted the harness thru top of left headlight assembly and across the top of the grill:

Now, I can easily disconnect the illuminated bow tie before removing the grill, next time:

Edited February 23, 2020 by Ravenkeeper

99silveradoz71 · February 23, 2020

Sprayed her off, then a rinseless wash to get rid of the salt.

CajunFries · February 23, 2020

Those are nice pods. Where did you get them from?

Sent from my SM-N975U1 using Tapatalk

SDHQ A pillar bracket
Baja Design spot/wide cornering facing forward
Rigid flood facing side ways

Sent from my iPhone using Tapatalk

VanguardK2 · February 23, 2020

SDHQ A pillar bracket
Baja Design spot/wide cornering facing forward
Rigid flood facing side ways

Sent from my iPhone using Tapatalk

Awesome thanks! I'll look into a pair of those for sure

Sent from my SM-N975U1 using Tapatalk

mdf21 · February 23, 2020

Put in the motofab 2.5”/2” kit. Happy with the results. Will put some ridge grapplers on when these wear out. Just have to figure out what size when that time comes

KJS Sullivan · February 23, 2020

Upgraded my brother in laws seats with Wet Okole covers!

Sent from my iPhone using Tapatalk

I can't see them. Must be cammo

Sent from my SM-N976V using Tapatalk

Golderado · February 24, 2020

King off road 2.5” coilovers with reservoirs,

i left a 1/4” of rake but looks level to the eye. Rides amazing compared to stock!

jgraves13 · February 25, 2020

King off road 2.5” coilovers with reservoirs,
i left a 1/4” of rake but looks level to the eye. Rides amazing compared to stock!

How’s the ride in the rear compared to stock? I have the front coilovers and fox 2.0 in the back, not sure if it’s worth the upgrade to Kings in the back

Sent from my iPhone using Tapatalk

6.2Midnight · February 25, 2020

I trailered home my new toy!

AZ_RADO_RNR · February 25, 2020

Added king 3.0 bypass shocks up front, removable tire cage w/ jack mounts and added quick release fire extinguishers to the bed cage. Brb while I go bully some Raptors.

Flexbrah · February 25, 2020

Swapped key fobs to the AJT key fob. Beyond happy with it and I really like the solid buttons rather than the frail rubber buttons thats on the original key fob.

Edited February 25, 2020 by Flexbrah

JimCost2014 · February 25, 2020

2 minutes ago, Flexbrah said:

Swapped key fobs to the AJT key fob. Beyond happy with it and I really like the solid buttons rather than the frail rubber buttons thats on the original key fob.

Do you have any pictures?

Flexbrah · February 25, 2020

2 minutes ago, JimCost2014 said:

Do you have any pictures?

Just added! Sorry trying to figure out how to add pics to the pist

JimCost2014 · February 25, 2020

25 minutes ago, Flexbrah said:

Just added! Sorry trying to figure out how to add pics to the pist

I see them, pretty stout looking!

Korazu · February 26, 2020

5 hours ago, Flexbrah said:

Swapped key fobs to the AJT key fob. Beyond happy with it and I really like the solid buttons rather than the frail rubber buttons thats on the original key fob.

Damn dude! I didn't need to see this, as I always wondered about other type replacements for the fobs. Too bad they didn't make a CNC machined aluminum instead of the injected plastic. Hardest decision of the day, what color combinations... LOL