2014+ K2XX - Center Console Swap / Retrofit - Plug and Play Harness!

[pgamboa]

Just finished installing. A big thanks to Phil video . Here is the picture you asked for devonb. I even added some blue led lights that come on when you open the door.

Very nice! Share some feedback about the install and the PnP Harness. .

Nice LEDs! As much as I like this, I couldn’t add blue LEDs to mine. I gave my son SO much grief about him adding blue LEDs to his car. LOL. Grief was about the way he installed them and not the lights themselves. So he will be me so much crap for adding Blue lights.

Nice work!


Sent from my iPhone using Tapatalk

[ChrisTaylor14]

I waited a long time to do this upgrade on my truck because I didn’t want to have to cut and splice the wiring in my truck and wanted everything to work as if the console were factory. So when I saw that Phil had created this harness I immediately purchased the console and contacted him to get my hands on one. 

I then saw Phil’s post about one of the members discovering he had a different plug under his seat (23 pin) and the harness would not work. I figured at this point I needed to take a closer look at my truck and ,just my lucky, I also had the 23 pin non supported plug.  

I reached out to Phil and let him know my situation and he advised that he was looking into a solution and would let me know when and if he found one. A few days later I saw Phil’s post about sending my old jumpseat harness with the 23 pin plug to him so that he could harvest the plug.

I again got in contact with Phil and got the harness sent out to him last Thursday. Today, only three short days later, I received the new harness in the mail. With the jumpseat already out of my truck, I completed the console upgrade in less than 30 minutes and was happy to see that everything works perfectly, just as factory. 

This was by far the easiest upgrade I have done to my truck thanks to Phil’s harness. Thanks again Phil! 

[Frank Jr]

2 hours ago, pgamboa said:

Very nice! Share some feedback about the install and the PnP Harness. .

Nice LEDs! As much as I like this, I couldn’t add blue LEDs to mine. I gave my son SO much grief about him adding blue LEDs to his car. LOL. Grief was about the way he installed them and not the lights themselves. So he will be me so much crap for adding Blue lights.

Nice work!


Sent from my iPhone using Tapatalk

Sure thing Phil. Got to tell you this PnP harness is tops. With out it this would be a night mare. Make sure to watch Phils video on how to install. I would add that there is three screws that hold the cig lighter and maybe called a place for a astray on dash that has to come off.. ( to me it just like a small glove box.).  I did have to loosen both back passage seat bolts. In fact I took them out just to make things easier to put floor console in truck. I was lucky that I had same set up as phil. I did order all three USB cables, only needed 2 of them. I do have the green one still in package.  If you are looking to add led lights as I did. Here is a few tips. I bought a kit that had 2   12" led lights with the 3m tape on them. I clean the inside of the side panels and stuck them on with the sticky side facing the doors of truck just about 1 " down. took wires and ran toward front of console. Added 16 gage wire to fed the power. If you want them to work when door opens and shut them self off just like dome light then what I did was took off fuse panel cover and drivers side windshield strip cover. Look for a gray wire. I had three off them. I took a test light and tested each one. The one which was dead and went live when door open is the one you want. Be careful  removing side panel next to windshield. There is a airbag set up there. At least my truck had it.  I ran my wire under dash to were the fuse box is and then ran it up the side of windshield. I made my connection there. You could got under dash on left side were there is a back box and connect there but trust me it was a lot easier to do what I did. After you make connection there go to the black wire from led lights and run it to fuse box. I ran both wires together at the same time and taped them together. At the side fuse box you will see 3 or 4 bolts  which will work as a very good ground. after that test just by open and closing door. On my truck with doors close the lights go out. Now if I turn on back over head lights nothing will happen. But if I turn on front over head lights the led lights turn on. Not hard to do and only took about 30 minutes to install. 

[Rosendojr]

Im interested in purchasing your dardness

[FSU1985]

22 hours ago, ChrisTaylor14 said:

I waited a long time to do this upgrade on my truck because I didn’t want to have to cut and splice the wiring in my truck and wanted everything to work as if the console were factory. So when I saw that Phil had created this harness I immediately purchased the console and contacted him to get my hands on one. 

I then saw Phil’s post about one of the members discovering he had a different plug under his seat (23 pin) and the harness would not work. I figured at this point I needed to take a closer look at my truck and ,just my lucky, I also had the 23 pin non supported plug.  

I reached out to Phil and let him know my situation and he advised that he was looking into a solution and would let me know when and if he found one. A few days later I saw Phil’s post about sending my old jumpseat harness with the 23 pin plug to him so that he could harvest the plug.

I again got in contact with Phil and got the harness sent out to him last Thursday. Today, only three short days later, I received the new harness in the mail. With the jumpseat already out of my truck, I completed the console upgrade in less than 30 minutes and was happy to see that everything works perfectly, just as factory. 

This was by far the easiest upgrade I have done to my truck thanks to Phil’s harness. Thanks again Phil! 

Any pics of the finished product?

[FourThor]

Just got my 2018, couldn't pass up the deal on what I got but it has the jumpseat. Is this harness and this part: https://www.gmpartsonline.net/oem-parts/gm-console-assembly-84131371/?c=Zz1ib2R5JnM9Y2VudGVyLWNvbnNvbGUmaT1HSDE0NTIwNSZyPTEmYT1jaGV2cm9sZXQmbz1zaWx2ZXJhZG8tMTUwMCZ5PTIwMTcmdD1sdCZlPTUtM2wtdjgtZmxleA%3D%3D correct? Is this all I would need besides a few other cords mentioned in the original post?

[Frank Jr]

3 hours ago, FourThor said:

Just got my 2018, couldn't pass up the deal on what I got but it has the jumpseat. Is this harness and this part: https://www.gmpartsonline.net/oem-parts/gm-console-assembly-84131371/?c=Zz1ib2R5JnM9Y2VudGVyLWNvbnNvbGUmaT1HSDE0NTIwNSZyPTEmYT1jaGV2cm9sZXQmbz1zaWx2ZXJhZG8tMTUwMCZ5PTIwMTcmdD1sdCZlPTUtM2wtdjgtZmxleA%3D%3D correct? Is this all I would need besides a few other cords mentioned in the original post?

I just went though this myself. do you have crew cab or double cab. You will need to look on internet at dealer trucks to find a truck  just the same as yours but with the floor console. you can get the vin number from the webs site/dealer. you need the last 8 numbers and letters from the vin. Give it to the web site and they will give you the correct part number. Remember the truck you look at with the floor console would be the same you will be ordering. so look at the trim. Next you will have to also order the front top trim and the side covers. Then you go with the usb cables you will need. The one you are looking at does not come with arm rest also and back cover. When I order my floor console I got the one with the back and arm rest. I only had to order the side panels and top trim and front mounting bracket. I also order all three usb cables. I only needed 2 of them. It cost me $970 total. that's with shipping. Then another $125 for Phil cable PnP. very much worth every cent. Remember if you give them your vin number then they will only sell you the one that came with your truck. I told my web site what I was doing and they told me to find another truck with the same year and cab. That is very important when ordering. Now you don't need lamp switch. They said I did and order it. It came with it.  you also don't need fender liner bolts , signal lamp assembly bolt,lower shield bolts. They said I needed them but didn't. Thinking about returning them. The console I got had everything except both side trims , upper trim panel, and console assembly front bracket. You really don't have to get the front bracket. I did because I wanted it nice and tight. With shipping it should be around $841 total. Now I also got the wireless charger arm rest. It was only $449.83 for my console and that came with the arm rest with wireless charger and back panel.See my picture of finished product above

 

Frank

Shipment Details Part Number Part Name Price Quantity Total 19303284 Cable $15.04 1 $15.04       19303285 Cable $15.21 1 $15.21       19119050 Cable $22.29 1 $22.29       84199886 Console $449.83 1 $449.83       23467516 Side Trim $23.37 1 $23.37       22817347 Side Trim $50.64 1 $50.64       84092079 Upper Trim Panel $140.14 1 $140.14       22876716 Lamp Switch $20.96 1 $20.96       11518341 Lower Shield Bolt $5.73 4 $22.92       22776807 Console Assembly Front Bracket $14.45 1 $14.45       11589012 Signal Lamp Assembly Bolt $0.68 4 $2.72       11609982 Fender Liner Bolt $2.84 6 $17.04       Subtotal: $794.61 Shipping (Ground Shipping ): $125.43 Total: $920.04 Check your order status Company Information GM Parts Online, 801 W. Business 83 McAllen, Texas, 78501 USA 1-866-423-9926 [email protected]

Edited January 15, 2018 by Frank Jr
add info.

[pgamboa]

2 hours ago, FSU1985 said:

Any pics of the finished product?

You looking for pics of the finished Plug and Play Harness?  If so, I updated the post and they are in the first post.  

[FourThor]

4 hours ago, Frank Jr said:

I just went though this myself. do you have crew cab or double cab. You will need to look on internet at dealer trucks to find a truck  just the same as yours but with the floor console. you can get the vin number from the webs site/dealer. you need the last 8 numbers and letters from the vin. Give it to the web site and they will give you the correct part number. Remember the truck you look at with the floor console would be the same you will be ordering. so look at the trim. Next you will have to also order the front top trim and the side covers. Then you go with the usb cables you will need. The one you are looking at does not come with arm rest also and back cover. When I order my floor console I got the one with the back and arm rest. I only had to order the side panels and top trim and front mounting bracket. I also order all three usb cables. I only needed 2 of them. It cost me $970 total. that's with shipping. Then another $125 for Phil cable PnP. very much worth every cent. Remember if you give them your vin number then they will only sell you the one that came with your truck. I told my web site what I was doing and they told me to find another truck with the same year and cab. That is very important when ordering. Now you don't need lamp switch. They said I did and order it. It came with it.  you also don't need fender liner bolts , signal lamp assembly bolt,lower shield bolts. They said I needed them but didn't. Thinking about returning them. The console I got had everything except both side trims , upper trim panel, and console assembly front bracket. You really don't have to get the front bracket. I did because I wanted it nice and tight. With shipping it should be around $841 total. Now I also got the wireless charger arm rest. It was only $449.83 for my console and that came with the arm rest with wireless charger and back panel.See my picture of finished product above

 

Frank

Shipment Details Part Number Part Name Price Quantity Total 19303284 Cable $15.04 1 $15.04       19303285 Cable $15.21 1 $15.21       19119050 Cable $22.29 1 $22.29       84199886 Console $449.83 1 $449.83       23467516 Side Trim $23.37 1 $23.37       22817347 Side Trim $50.64 1 $50.64       84092079 Upper Trim Panel $140.14 1 $140.14       22876716 Lamp Switch $20.96 1 $20.96       11518341 Lower Shield Bolt $5.73 4 $22.92       22776807 Console Assembly Front Bracket $14.45 1 $14.45       11589012 Signal Lamp Assembly Bolt $0.68 4 $2.72       11609982 Fender Liner Bolt $2.84 6 $17.04       Subtotal: $794.61 Shipping (Ground Shipping ): $125.43 Total: $920.04 Check your order status Company Information GM Parts Online, 801 W. Business 83 McAllen, Texas, 78501 USA 1-866-423-9926 [email protected]

Thanks for the detailed information Frank, much appreciated.

[FourThor]

2 hours ago, FourThor said:

Thanks for the detailed information Frank, much appreciated.

I may just go ahead a

 

5 hours ago, Frank Jr said:

I just went though this myself. do you have crew cab or double cab. You will need to look on internet at dealer trucks to find a truck  just the same as yours but with the floor console. you can get the vin number from the webs site/dealer. you need the last 8 numbers and letters from the vin. Give it to the web site and they will give you the correct part number. Remember the truck you look at with the floor console would be the same you will be ordering. so look at the trim. Next you will have to also order the front top trim and the side covers. Then you go with the usb cables you will need. The one you are looking at does not come with arm rest also and back cover. When I order my floor console I got the one with the back and arm rest. I only had to order the side panels and top trim and front mounting bracket. I also order all three usb cables. I only needed 2 of them. It cost me $970 total. that's with shipping. Then another $125 for Phil cable PnP. very much worth every cent. Remember if you give them your vin number then they will only sell you the one that came with your truck. I told my web site what I was doing and they told me to find another truck with the same year and cab. That is very important when ordering. Now you don't need lamp switch. They said I did and order it. It came with it.  you also don't need fender liner bolts , signal lamp assembly bolt,lower shield bolts. They said I needed them but didn't. Thinking about returning them. The console I got had everything except both side trims , upper trim panel, and console assembly front bracket. You really don't have to get the front bracket. I did because I wanted it nice and tight. With shipping it should be around $841 total. Now I also got the wireless charger arm rest. It was only $449.83 for my console and that came with the arm rest with wireless charger and back panel.See my picture of finished product above

 

Frank

Shipment Details Part Number Part Name Price Quantity Total 19303284 Cable $15.04 1 $15.04       19303285 Cable $15.21 1 $15.21       19119050 Cable $22.29 1 $22.29       84199886 Console $449.83 1 $449.83       23467516 Side Trim $23.37 1 $23.37       22817347 Side Trim $50.64 1 $50.64       84092079 Upper Trim Panel $140.14 1 $140.14       22876716 Lamp Switch $20.96 1 $20.96       11518341 Lower Shield Bolt $5.73 4 $22.92       22776807 Console Assembly Front Bracket $14.45 1 $14.45       11589012 Signal Lamp Assembly Bolt $0.68 4 $2.72       11609982 Fender Liner Bolt $2.84 6 $17.04       Subtotal: $794.61 Shipping (Ground Shipping ): $125.43 Total: $920.04 Check your order status Company Information GM Parts Online, 801 W. Business 83 McAllen, Texas, 78501 USA 1-866-423-9926 [email protected]

Looks like you have the jet black console and silver trim correct? I may just go ahead and order everything you did as I have the jet black cloth interior with silver trim. Did the console you buy come with the wireless charger or was that a separate piece? Is there a separate part for the back of the console?

[Fall Sniper]

Just finished installing. A big thanks to Phil video . Here is the picture you asked for devonb. I even added some blue led lights that come on when you open the door.

Nice touch


Sent from my iPhone using Tapatalk

[FourThor]

Per Frank's suggestion of giving the GM Parts retailer my vin and having them build a parts list this is what they advised me to purchase. 

 

84092079 Front floor console trim panel; Reverse Tartan finish.

22776807 Front floor console bracket.

11589012 Bolt; 4 per vehicle.  Sold individually.

11609982 Front floor console bolt; 6 per vehicle.  Sold individually.

84288040 Front floor console; black in color.

11518341 Front floor console bolt; 4 per vehicle.  Sold individually.

23467516 Driver side front floor console extension panel; black in color.

22817347 Passenger side front floor console extension panel; black in color. 

84330208 Front front floor console armrest; black in color.

23124536 Front floor console wiring harness extension harness (wireless charging jumper).  Unfortunately, this part is currently on backorder from GM. There is not an estimated time when GM will have stock available. 

23359464 Front floor console rear trim panel.

22816697 Front floor console rear cover; black in color.

 

Is any of this extraneous? Assuming I won't need the wireless harness extension? Total's to be about $1000 not including shipping or the plug n play harness required to get it all to work. 

Edited January 15, 2018 by FourThor

[Frank Jr]

1 hour ago, FourThor said:

Per Frank's suggestion of giving the GM Parts retailer my vin and having them build a parts list this is what they advised me to purchase. 

 

84092079 Front floor console trim panel; Reverse Tartan finish.

22776807 Front floor console bracket.

11589012 Bolt; 4 per vehicle.  Sold individually.

11609982 Front floor console bolt; 6 per vehicle.  Sold individually.

84288040 Front floor console; black in color.

11518341 Front floor console bolt; 4 per vehicle.  Sold individually.

23467516 Driver side front floor console extension panel; black in color.

22817347 Passenger side front floor console extension panel; black in color. 

84330208 Front front floor console armrest; black in color.

23124536 Front floor console wiring harness extension harness (wireless charging jumper).  Unfortunately, this part is currently on backorder from GM. There is not an estimated time when GM will have stock available. 

23359464 Front floor console rear trim panel.

22816697 Front floor console rear cover; black in color.

 

Is any of this extraneous? Assuming I won't need the wireless harness extension? Total's to be about $1000 not including shipping or the plug n play harness required to get it all to work. 

They are selling you to much stuff. Bolts you can reuse from your console now. The only bolts you will need is the 2 bolts that bolt to the front bracket.  Yes my console is black with silver trim. Yes it came with the back panel and yes it did come with the wireless charger. If you want what I have then use these part numbers. 

Console with back and arm rest with wireless charger   # 84199886

upper front trim panel # 84042079

front mounting bracket #  22776807

side trim right and left # 23467516 and # 22817347

That's it. Now for your USB cables Need to know if you have a cig/ lighter port on dash and 110 out let. This will depend on what USB cables you need.

and Phil PnP cable.

I used gmpartsonline.net  they gave me the best price after checking over 6 sites. They will have to order the console and it will take them 3 to 4 days to get.

1-866-423-9926

Edited January 15, 2018 by Frank Jr

[Frank Jr]

Is this what you have on your dash? cig /port and a 110 outlet?  If it is then you need to order 2 USB cables as follows  # 19303285 and # 19119050

 

IMG_0176.MOV

Edited January 15, 2018 by Frank Jr

[FourThor]

They are selling you to much stuff. Bolts you can reuse from your console now. The only bolts you will need is the 2 bolts that bolt to the front bracket.  Yes my console is black with silver trim. Yes it came with the back panel and yes it did come with the wireless charger. If you want what I have then use these part numbers. 
Console with back and arm rest with wireless charger   # 84199886
upper front trim panel # 84042079
front mounting bracket #  22776807
side trim right and left # 23467516 and # 22817347
That's it. Now for your USB cables Need to know if you have a cig/ lighter port on dash and 110 out let. This will depend on what USB cables you need.
and Phil PnP cable.
I used gmpartsonline.net  they gave me the best price after checking over 6 sites. They will have to order the console and it will take them 3 to 4 days to get.
1-866-423-9926

This is my configuration and trim. I believe this silver is the reverse tartan?



Sent from my iPhone using Tapatalk