Jump to content

Shake or Vibration Issues

Silver space ship
 Share

Recommended Posts

mdes0 Enthusiast

mdes0

Posted
Posted

I picked up my 2014 Sierra All Terrain last night and so far everything has been great. I test drove it the day before to give the dealership the ok to spray the bed liner and during the test drive I noticed a vibration mostly through the steering wheel, like some have described. I told the dealer and they had the service department look at it before I picked it up last night. They force road balanced the tires and the vibration is gone, drives beautifully. My vibration came on around 75 and persisted through 80+. Was very slight under 75. Only have 120 miles on it so if anything changes I'll let you guys know.

  • Like 2
  • Replies 12.9k
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

csckickass
csckickass

Well folks, I did it. After all the failed attempts at the Chevy dealer I traded it in for a 2015 Ram 1500 Larame. I have to agree with the other folks on here that have done the same thing, it was th

mafd2
mafd2

Apparently you and the other customer reps don't care. If you or GM would care y'all would put more effort in the matter. Just coming on the forum and stating the same repetitive posts and being a 3

DALaws
DALaws

Well I have some good news and bad news about my truck vibrations. Good news is that my truck has a significantly less vibration at speed. The bad news is my truck has significantly less vibration. Fo

Posted Images

GMCustomerService Senior Enthusiast

GMCustomerService

Posted
Posted

barky,

 

I understand that you are unhappy with some concerns that you are experiencing with your vehicle. I am happy to look into these concerns for you. Please private message me referencing this thread including you name, address, phone number, VIN, exact mileage, and preferred dealership.

 

Jennifer T.

GM Customer Care

 

 



Szyikowski Enthusiast

Szyikowski

Posted
Posted (edited)

 

So today I just pulled my 600# snowmobile on a 2 place aluminum snowmobile trailer and had the worst vibrations I've experience so far. This has me more convinced my vibration issue is related to drive shaft angle. The weight on the back of the truck is slightly lifting the front and in any other truck this isn't an issue but since my truck has a vibration unloaded the extra drive shaft angle makes it worse. How does a guy get a proper drive shaft angle?

That is my exact problem too. Not sure if you saw my post towards the top of this thread but I actually rotated my tires on my trailer in a Walmart parking lot because the vibration was so bad with a similar trailer. I am confident that this is a prop shaft issue and GM knows it. It will just be a matter of time before a recall goes out. Edited by Szyikowski
Pfmet New Member

Pfmet

Posted
Posted

So has anyone really determined whether its tires, axles, driveshatfs, or whole rear ends? I guess I'll start with tires. I have a very slight but noticalbe vibration at ALL speeds. I've called the dealer who said to bring it in but I haven"t had time yet.

Silver space ship Enthusiast

Silver space ship

Posted
  • Author
Posted

I actually was trying to get video of how bad my had would shake on the wheel when pulling the trailer. I think if I added my buddy's snowmobile on the trailer it wouldn't be drivable. I think today I'm going to put my ATV in the box (650#) and take it for a drive just to rule out the trailer, although I've never had a problem with the trailer before. If it vibrates bad I will bring it to the dealer with it in the back on Tuesday when they fix my seat.

Silver space ship Enthusiast

Silver space ship

Posted
  • Author
Posted

Just got done with taking for a ride with my ATV in the back. It drove the same as it does empty, so it the weight might not be far enough back to have the same effect as having all the weight on the receiver hitch.

mdes0 Enthusiast

mdes0

Posted
Posted

Silver Spaceship, you ever have your tires road force balanced? If they are off extra load would definitely make it worse. I know people have been saying the pinion angle could be off but I don't see how that would cause a vibration unless the spring blocks in the rear suspension had different angles cut in them or if one didn't seat on the rear end properly. I have experienced vibrations above 50 in a different car when the u-joint wasn't bolted to the rear end properly, kid who bolted it up didn't notice that one side was sitting on the alignment tab.

As others have mentioned could be a out of balance drive shaft. Could also be a defective u-joint somewhere on the drive line. With all the tire related issues I've seen posted I would lean that way though, and as I mentioned in an earlier post my vibration which came on about 70, went away once the dealer road force balanced the tires. I also towed my 6k lb boat yesterday and no vibrations at all, pulled like a bull.

Jimmy W Enthusiast

Jimmy W

Posted
Posted

Well I went and got on the interstate this morning after reading this to check mine at the higher speeds and guess what?When it reached 82 mph the vibration started and was terrible!!Drives so smooth at speeds below 80 with zero vibration!

  • Like 1
joeocean New Member

joeocean

Posted
Posted

Well scheduled my 3 rd trip to dealer for THE SHAKE that everyone unfortunate buyer is experiencing. So far they have replaced all 4 tires and road force balanced them and vibration/shake is still there at speeds above 65.

The dealers can't fix an engineering problem. This must be addressed from GM's engineers. I'm going to lemon law it if they can't address this miserable issue.

Stex Senior Enthusiast

Stex

Posted
Posted

Well I went and got on the interstate this morning after reading this to check mine at the higher speeds and guess what?When it reached 82 mph the vibration started and was terrible!!Drives so smooth at speeds below 80 with zero vibration!

 

It is the tires. I had vibs over 70 mph and was corrected by tire trueing and balance on the truck. If such is not available to your area, recommend you find a shop or discount tire that knows how to properly road force balance a tire. If it takes too much weight, have them rotate the tire 180 on the wheel. Or just stay below..80..if you are kidding about this

svtkidd23 Enthusiast

svtkidd23

Posted
Posted
Well scheduled my 3 rd trip to dealer for THE SHAKE that everyone unfortunate buyer is experiencing. So far they have replaced all 4 tires and road force balanced them and vibration/shake is still there at speeds above 65.

The dealers can't fix an engineering problem. This must be addressed from GM's engineers. I'm going to lemon law it if they can't address this miserable issue.

How bad is yours?

My area 3x same issue is a lemon case

Jimmy W Enthusiast

Jimmy W

Posted
Posted

Mine drives so nice and smooth up to about 82-85 mph and it is like you flip a switch!!I went to the dealership today to see when they could look at it and if they have heard of this before.Guess what they said??We have not ever had that problem before,My appointment is for 10 am tomorrow we will see!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • Gkistler
      2015 Sierra Denali L86 cyl 5 misfire at idle

      By Gkistler · Posted

      Hi friends - first time poster. I have a 2015 sierra Denali with 150k miles, I’m the second owner and she’s given me 75k of great service. I run a pulse AFM disable device. Starting Thursday when I exited the freeway after a short local ride it started idling rough, with an obvious misfire shake and was down on low end power.  I got it home and hooked it up to my scannner and found no codes but in live data a pretty bad misfire on cylinder 5. I replaced the coil, plug and wire with all new OE replacements (Delphi gn10165 coil, acdelco wire and 41-168 plug). It’s still behaving the same way after firing the parts cannon at it.   I know cyl 5 is a non AFM cylinder so I am not thinking this is AFM related but I’m kinda at a loss. injector? Bent pushrod? It’s running too well over 1k rpm to suggest those IMO. Has anyone chase this issue before and what was it? Any suggestions? 
    • zibzer2
      Pulsating Noise 4Cyl Mode

      By zibzer2 · Posted

      2017 Silverado L83 5.3l 6speed transmission Hello, not a new member but havent posted in a while and my old signup info isnt working so had to create a new account. anyways, I have an issue with my truck and hope someone can spread some light on whats happening: -when it goes to 4cyl mode it makes a clunk sound (but not when coasting or going downhill) -when in 4 cyl mode and under load it makes a load pulsating sound (not a tick). -goes away completely when in M5 gear or when plugging in an AFM delete. Im guessing it is one of 2 things but im not convinced of either to be honest. 1. lifter stuck in v8 mode 2. torque converter shudder realistically it doesn't seem like the TC as there is no physical vibration , and it never happens in v8 mode. but maybe? and wouldnt a lifter make a sound whether with load or not? any ideas let me know please. thank you!  
    • Chuck FB
      Some Assembly is Required

      By Chuck FB · Posted

      Which has made me wonder with the various engine failures of a few brands in the last few years, is it sub par materials such as lifters etc causing failures, or bearing clearances on the crank etc or perhaps bad designing of an engine physically or causing too much load on the components due to the hp/torque they can push out of them. Or is the oil viscosity and additive package of current oils or a lack of oil flow by an oil pump not able to supply sufficient oil at idle or under high load at low rpm. Or is it every item I listed that combined together has pushed the limits so far to the left that there is hardly a margin of safety left and add in some fuel dilution and too long of an OCI and premature engine failure is the result ?. 
    • Grumpy Bear
      Some Assembly is Required

      By Grumpy Bear · Posted

      He is not saying that an SAE *W20 will have more viscosity than a *W40 due to MORE VII polymers. He is saying that although multiple *W40 may post in the PDS the same or similar 100 C and 150 C viscosities that the blenders choice of modifier TYPE and AMOUNT to get his chosen base to grade will not give identical real world viscosities in shear and at temperature. All will pass the SII test but not all will pass the 100 C HTHS (unpublished value) testing the blender does and relies on to get the required by law "percentage improvement' referenced to his last great work.    Tis the problem with the lie. Once told others are required to support it. 
    • PunchT37
      Parking Brake - Automatic Engagement Questions

      By PunchT37 · Posted

      I have a `25, 1500 that auto sets on incline. Never knew that at first. I have the electronic shifter. Just think if it didn`t do that? Unlike a mechanical shift that you can muscle out of park, how would you get this thing out? That would be a problem.   What I found out later is, I don`t have to push the button to release. Just put it in gear.   Setting parameters? Don`t know if it`s possible.

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...