Jump to content

Shake or Vibration Issues

Silver space ship
 Share

Recommended Posts

thehad Enthusiast

thehad

Posted
Posted (edited)

gjk1932 I think there is a problem with all Goodyear tires that come on these trucks. My truck came with the Goodyear Eagle LS-2 tires. I am glad to hear that some of you have swapped the tires to another brand and have either fixed the issue completely or reduced it to a non-issue.

 

I have no further updates since my last post since I haven't made any trips after getting my truck back three weeks ago. I've been working 70+ hrs a week and haven't had any time to just get out on the road to test the tires or make a trip. I may get a trip in this weekend, so I might have a conclusion on the fix I got next week. I've been thinking about replacing the tires but haven't had the time to do so or the want to spend the money. I'll make that decision after I get a long trip in.

Edited by thehad
  • Replies 12.9k
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

csckickass
csckickass

Well folks, I did it. After all the failed attempts at the Chevy dealer I traded it in for a 2015 Ram 1500 Larame. I have to agree with the other folks on here that have done the same thing, it was th

mafd2
mafd2

Apparently you and the other customer reps don't care. If you or GM would care y'all would put more effort in the matter. Just coming on the forum and stating the same repetitive posts and being a 3

DALaws
DALaws

Well I have some good news and bad news about my truck vibrations. Good news is that my truck has a significantly less vibration at speed. The bad news is my truck has significantly less vibration. Fo

Posted Images

brandon1282 Enthusiast

brandon1282

Posted
Posted

Update: Just was informed that GM has advised the dealership to change out the Torque converter and the Transmission Control Module. My truck should be ready on Tuesday. In the mean time they have given me another 2014 sierra as a loaner....I am interested to see if in the time I have this truck if I notice the same vibration.

 

As far as tires go, I think we may be talking about two different issues here. The problem I am experiencing (as well as some others on this thread) is intermittent at speed, not a continuous vibration that occurs above a certain speed. If the later is the case, then yes I agree, the first thing I would look at is a problem with tires (or possibly the drive shaft). The problem I am having does not occur every time I am at a certain speed or operating under the same conditions (i.e. it only seems to happen under moderate power between 50 and 65, but does not occur everytime I am under moderate power between 50 and 65).

 

As always, I'll keep you posted of the findings/results.

8thsense Enthusiast

8thsense

Posted
Posted

My z71 package is pretty stiff as well and ended up being stiffer than the std package truck I test drove. I had to have the Z71 grill, so shocks I can change back to twin tube for smoother ride at anytime:)

  • Like 1
GMCustomerService Senior Enthusiast

GMCustomerService

Posted
Posted

brandon1282,

 

Hello! I am glad to hear that your preferred dealership was able to resolve your vehicle issue and you will be able to have your vehicle back by Tuesday. Please keep us updated if you are satisfied with the repair. Please know that GM Customer Care is here and happy to assist!

 

Jennifer T.

GM Customer Care



skiguy213 Enthusiast

skiguy213

Posted
Posted

Well it has been about 200 miles since the dealer swapped the goodyears for Bridgstones and yes the wobble is gone, but I have to say this is the worst truck ever. The steering wheel is not smooth there is a constant slight vibration that is not tire related and even the smallest cracks in the road feel like you are hitting giant pot holes and the whole truck bounces. Every little thing is felt directly through the steering wheel.

 

If anyone is reading this post DO NOT BUY ONE OF THESE!!! I have had at least 10 chevy and GMC trucks and never had such an awful time driving a vehicle as this one. Can't wait to trade out of it.

BringTheRain403 Senior Enthusiast

BringTheRain403

Posted
Posted

Well it has been about 200 miles since the dealer swapped the goodyears for Bridgstones and yes the wobble is gone, but I have to say this is the worst truck ever. The steering wheel is not smooth there is a constant slight vibration that is not tire related and even the smallest cracks in the road feel like you are hitting giant pot holes and the whole truck bounces. Every little thing is felt directly through the steering wheel.

 

If anyone is reading this post DO NOT BUY ONE OF THESE!!! I have had at least 10 chevy and GMC trucks and never had such an awful time driving a vehicle as this one. Can't wait to trade out of it.

I don't have this issue. Mine rides better than my buddies 5-series and I have Z-71 with 22's...

 

Sent from my SCH-I535

  • Like 1
svtkidd23 Enthusiast

svtkidd23

Posted
Posted
Well it has been about 200 miles since the dealer swapped the goodyears for Bridgstones and yes the wobble is gone, but I have to say this is the worst truck ever. The steering wheel is not smooth there is a constant slight vibration that is not tire related and even the smallest cracks in the road feel like you are hitting giant pot holes and the whole truck bounces. Every little thing is felt directly through the steering wheel.

 

If anyone is reading this post DO NOT BUY ONE OF THESE!!! I have had at least 10 chevy and GMC trucks and never had such an awful time driving a vehicle as this one. Can't wait to trade out of it.

My steering wheel feels it all to.. And the rumble strips feel like craters lol
mdes0 Enthusiast

mdes0

Posted
Posted

Mine is quieter and smoother than my last three Infinitis. Sounds like you got a bad one.

  • Like 1
Stex Senior Enthusiast

Stex

Posted
Posted (edited)

Well it has been about 200 miles since the dealer swapped the goodyears for Bridgstones and yes the wobble is gone, but I have to say this is the worst truck ever. The steering wheel is not smooth there is a constant slight vibration that is not tire related and even the smallest cracks in the road feel like you are hitting giant pot holes and the whole truck bounces. Every little thing is felt directly through the steering wheel.

 

If anyone is reading this post DO NOT BUY ONE OF THESE!!! I have had at least 10 chevy and GMC trucks and never had such an awful time driving a vehicle as this one. Can't wait to trade out of it.

What are you driving?

 

Your steering senses what the tires send thru to the steering components. Save your trade loss by going and getting some good Michelins LTX tires and a good road force balance. Brigs are not that good. Discount gave me a good price trade on mine. I drove from the dealership straight to Discount and had Michelins put on the same day I picked up my truck.

 

then if we can find some Bilstein 5100s for these '14s you should be good.

Edited by STex
  • Like 1
brandon1282 Enthusiast

brandon1282

Posted
Posted

Update: Just was informed that GM has advised the dealership to change out the Torque converter and the Transmission Control Module. My truck should be ready on Tuesday. In the mean time they have given me another 2014 sierra as a loaner....I am interested to see if in the time I have this truck if I notice the same vibration.

 

As far as tires go, I think we may be talking about two different issues here. The problem I am experiencing (as well as some others on this thread) is intermittent at speed, not a continuous vibration that occurs above a certain speed. If the later is the case, then yes I agree, the first thing I would look at is a problem with tires (or possibly the drive shaft). The problem I am having does not occur every time I am at a certain speed or operating under the same conditions (i.e. it only seems to happen under moderate power between 50 and 65, but does not occur everytime I am under moderate power between 50 and 65).

 

As always, I'll keep you posted of the findings/results.

 

 

Just to update everyone on the rumble strip vibrations I was experiencing. I got the truck back 2 days ago and so far so good. Here is what the dealer reported:

 

Road tested vehicle and found possible tire/wheel vibration. Removed all four wheels and road force balanced to find one tire out of range. This tire was replaced and then vehicle was road tested again. The vibration improved but was not eliminated. Checked for TSB's and none were found that directly addressed this concern. Contacted TAC and TAC suggested to utilize TBS PIP5149B. I followed all instructions of this TSB, checking for excessive spark retardation and connecting rod oil squitter condition. There were no conditions observed. TAC then directed me to utilize DOC ID#2102430 where I checked the operation of the control solenoid within the transmission. When commended to the on position, It registered full pressure and when commanded off it registered 0 pressure. After completing all tests found that TCM could not be 'pulse-width' tested, only command on or off. With these measurements we determined that the TCM was sending an erratic signal causing the torque converter to be commanded erratically. This caused potential damage to torque converter. Therefore, I replaced the TCM (Signal) and torque converter (damaged internally). Road tested vehicle; now operating to GM specifications with no vibration when tested under the original conditions.

 

I have also noticed that the "floating Tac" condition I had earlier is no longer present.

  • Like 2
brandon1282 Enthusiast

brandon1282

Posted
Posted

Yes. When the cruise was set on a steady up hill climb the tachometer would float I.e. kind of fluctuate in a range of RPMs; not hold steady.

svtkidd23 Enthusiast

svtkidd23

Posted
Posted
Yes. When the cruise was set on a steady up hill climb the tachometer would float I.e. kind of fluctuate in a range of RPMs; not hold steady.

Mine kind of floats

GMCustomerService Senior Enthusiast

GMCustomerService

Posted
Posted

skiguy213,

 

I am truly sorry to hear that you are unhappy with your vehicle and the issues you are experiencing. I am interested in learning more about your concerns. Please private message me referencing this thread.

 

Sincerely,

 

Jennifer T.

GM Customer Care

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • Grumpy Bear
      Some Assembly is Required

      By Grumpy Bear · Posted

      www.enginelabs.com/news/what-i-learned-today-bearing-clearances-vs-oil-viscosities/     www.enginelabs.com/news/oil-viscosity-can-the-numbers-be-misleading/ The Big Lie… Coming full circle to the reason Lake discusses the Porsche engines in particular. Based on the 2000 samples in the SPEEDiagnostix database, increasing the oil viscosity in these engines, even those run on the track, showed no significant difference in results.   The smoking gun was in the oil chemistry. That is where the data shows higher instances of more wear. Molybdenum was the key; the higher the amount, the less the wear. Speed postulates that higher viscosity oils have more thickeners to artificially inflate their viscosity numbers. These thickeners lose viscosity under shear, and the result is that not all oils of the same viscosity have the same shear stability.   Having enough viscosity is the most important characteristic, but according to Speed, once that required viscosity level is reached, additive chemistry matters more than additional viscosity. Speed also states, oil pressure problems on the racetrack aren’t a viscosity problem; it’s an oiling system problem. Running a thicker oil is just a band-aid for an underlying oiling system problem.
    • Grumpy Bear
      Some Assembly is Required

      By Grumpy Bear · Posted

      Can it still be Assembled II?   Viscosity on the decline by various means. Heat on the rise making that worse. Engine RPM in the tank. Smaller motors with more boost trying to emulate an electric motor. Full torque, zero rpm. Then we will triple the OCI. Argh.    But wait....there is more. LSPI has pushed a shift from Ca to Mg and as that cost more PLUS the run to lower sulfur compounds the TBN is moving in the wrong direction for the increased OCI's demanded.    That not being enough to placate a demand for a parameter they can't measure the other sulfur bearing compounds are also under attack. That would be zinc and phosphorus sulfonate compounds. To some degree those are being replaced with boron esters and others, i.e. titanium ect. All of which have shorter service lives. And there there is the "Secrete Sauce" marketing for AW adds that 'Can't be detected by UOA's" but trust me because I (the blenders) never ever lie.    Spoiler alert; ALL additives are sacrificial! Smaller amounts of the old blended with less robust versions of the new do not equal longer service lives. So what are the blenders recommending? Wait for it.......   MOVING THE GOAL POSTS! OMG      Let's declare the long standing TAN/TBN crossover irrelevant and tell people that soot is a great 'graphite' based lubricant which can aid tribo films. Wait, what? Let's declare that the standards used for oxidation and nitration were to conservative and can be expanded. Let's tell them that because GDI fuel dilution, although being a VISCOSITY KILLER and an acid generator is actually okay because we have better base oils that limit viscosity failure limits. (Said knowing this is measured in fractions of a centipoise and in bases not commonly used in shelf oils)   Lying from the heart is not just the new normal but we have a public, a very young public, that is so ignorant of the facts and so sure of their "RESEARCH" into AI driven models base in regurgitated  instead of scientific research based unvarnished, peer reviewed FACTS that the incoming guard is loosing their grip on reality and the OEM's are tickled pink while the blends bend the knee.    You have an ever limited set of tools to work with. And sooner or later those will be taken from you as the API and the EPA strangle the last remaining fluids from the system. What you have left is your wits. If you care to use them.    At some point in the very near future it will not longer be possible to do "What is best for the machine", and be replaced with "The best you have access too". You WILL be rewarded with half the life and twice the cost. That isn't that hard to predict.         
    • Chuck FB
      Software Update

      By Chuck FB · Posted

      I trust you saw the other comment where he knew what he was talking about !. Yes, these darned newer vehicles with all their so smart they are stupid technology, goes and drains the battery down. As you might see my other comment, I installed a Noco 5 battery tender under the hood and at this point still have the cord routed so I have to lift the hood and then plug it in but am typically parked in a garage or a shed so its not risking the engine hood in the wind. That way I am assured or hopefully so of not finding I have a battery drawn down and can't even start the truck and that also damages the battery to draw it down too far. 
    • Chuck FB
      Software Update

      By Chuck FB · Posted

      I guess no surprise my guesses were wrong !, at least now I know if I ever happen to see it grayed out in my own truck as to what is going on.    I never happened to catch my truck with it grayed out, it seemed every time I would test to see if there was an update it never found anything and yet more than once I would check to see if there was an update and there was nothing, then a day later or even that same morning I would drive to town and after more than one engine shut down in town as I did my errands it would pop up that there is an update now ready to install and the only place I have a connection to the internet is at home by wifi so its not as if it grabbed the download while driving. I don't trust these new vehicles due to all the crap they can decide to do while sitting for some days not running and run the battery down so most of the time if I know the truck will sit for a few days I plug in the battery tender I have mounted under the hood and so the only time the truck must have downloaded software was when it was sitting in the garage where the signal is awful but I have that tender plugged in and somehow it managed to download it. I honestly detest all this crap, way to easy to leave a person stranded.    Since I don't trust any of it I don't do the install of the already downloaded software until I get home and sometimes have even sat in the truck to watch what its doing as its going through the process to its conclusion as its not like it is set up that it will tell you the next time you fire up the engine that the update that was initialed actually installed or installed properly. Yes I can go into the updates and see the list. After I go through the install where I feel its safe to do so in case it breaks down as a result, I will plug in the battery tender after the fact to recharge as I don't know how much power its taking just to do the install and that can take a while for it to install. 
    • nfisherman
      Software Update

      By nfisherman · Posted

      Thanks for the reply. All settings were correct and the engine was off, as it was supposed to be. It turned out to be something simple. I took a drive for about an hour. I must have had a low battery without knowing it. The voltage gauge on the display looked ok. At the end of my drive, I shut off the engine and the update prompt came up and it updated normally. It’s ironic because one of the features of the update is a reduction of battery drain. 

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...