Jump to content

Recommended Posts

Posted (edited)

Shimmy - My 14 Sierra had the 45-55 vibe. Tracked to a badly out of specs ring gear. I have a 15 rear end and no vibration.

 

Thank you for the info - So they replaced your entire rear end with a '15 rear end or did they go about it differently?

 

Did you happen to experience the seat and console shake?

Edited by Shimmy Bang Bang
Posted

The vibration was a distinct "tiny rumble strip" feeling as described early in this forum by me and others. Pretty much a complete rear end less brakes, tires, and wheels as I understood.

Posted

 

Thank you for the info - So they replaced your entire rear end with a '15 rear end or did they go about it differently?

 

Did you happen to experience the seat and console shake?

 

My truck also got a new rear axle assembly, which fixed the 50mph steering wheel vibration.

 

The seat and console shake can be due to a few different parts being out of spec, prop shaft, drive shaft, tires, to name a few.

 

An internal source within GM explained to me that they had multiple issues with multiple suppliers providing out of spec parts...all of which ended up on the 1500 pickup trucks.

 

That's why it has been so hard to diagnose. Tires might fix one truck, but the next might have 4 out of spec parts and still vibrate after a tire swap/balance.

 

The shame is that GM continues to build trucks with these faulty parts, KNOWING they have problems. To make matters worse, nearly every test drive consists of driving a few miles up and down the nearest road, never going above 45...and all of these vibe problems happen at highway speeds. I suppose if I was GM and in it for the cash, I would do the same thing...wait for customers to buy the truck, get it home, drive on the express way to work, feel the vibration...then live with it, or complain.

 

If you have any of these vibration problems, GET THE BBB INVOLVED! They are your only way out!

Posted

The vibration was a distinct "tiny rumble strip" feeling as described early in this forum by me and others. Pretty much a complete rear end less brakes, tires, and wheels as I understood.

Very interesting. I think there have been reports of replacing crown and pinions (on this thread and the SUV thread) and it not helping, but you had the entire rear end housing replaced. That's a whole other situation! Seems to me there was an early report of doing the same on an SUV on a different website, and it solved the issues with the SUV's (booming/buffeting/vibration). So, this may be on to something.

Posted

I wish service managers actually cared about their customers and had half a brain and read these topics. If I was a service manager, i would.

  • Like 1
Posted

I wish service managers actually cared about their customers and had half a brain and read these topics. If I was a service manager, i would.

Probably better if they had a whole brain instead of a half! LOL!

  • Like 1
Posted

The vibration was a distinct "tiny rumble strip" feeling as described early in this forum by me and others. Pretty much a complete rear end less brakes, tires, and wheels as I understood.

What you have described (tiny rumble strip feel) is your front differential. Needs replacement or complete overhaul. You may find this thread /post linked below more useful and related. This is not the resolution to all, but for those SPECIFIC to "tiny rumble strip" feel issues, its worth reviewing. We have several members (including myself) who got their dealerships (NOT EASY) to replace the entire front differential assembly, which resolved the issue and for most part trucks rode smooth as glass again.

 

http://www.gm-trucks.com/forums/topic/154976-2014-sierra-humming-noise/page-9?do=findComment&comment=1607902

Posted

Gosh, it almost seems that I need both my rear and front swapped out since I have the 45-55 buzzing vibration and the 74-80 mph console seat shake. I wanna cry,

Posted

I'm reading through this thread because I have the same problem with my 2009!

It's unbelievable that this is still going on and I hate to tell you guys it only get worse as the truck get older. My 2009 with 71k shakes so bad sometimes on the highway I'm scared a wheel is going to fall off. I was seriously thinking about buying a new truck because of this but after reading this thread no F'in way!

My truck was pretty smooth when I first got it so I feel I could easily be tricked in a test drive and end up with another shaker!!

I my end up with a Ford even though I love the looks and power of the GM truck.

Posted

GM-GUY - The ring gear was checked and found to be grossly out of spec. Upon replacing the rear diff and axle the vibrations were gone... How does that square with your statement. Should I now, 9 months and 20,000 miles without any vibrations, return to the dealer and ask the service mgr to look for problems in the front end...? I can see that that might be "not easy" but you sound quite sure of your position.

Posted

Just to review, what was the solution to the 70-80mph console and passenger seat shake?

 

In searching for a replacement for my truck, I've driven 11 Seirra and Silverados now. 8 of them had this problem. I found none with the gas pedal vibe (although my 2014 has it) and none with the steering wheel vibe. Nearly all of them have the console/seat shake though.

 

The trucks that rode smooth, 2 were demo trucks with 2500 and 5000 miles on them (probably had issues and were fixed), and the other was a long box v8 crew, with 20" Continental tires.

Posted

...The ring gear was checked and found to be grossly out of spec. Upon replacing the rear diff and axle the vibrations were gone...

Did you have your vibration from basically day one and as you put more miles on the truck did it seem to slowly get worse?

Posted

@PMmury, only if experiecing a rumble strip type hum/feel between 55-72mph. I see on prev post you had the less then 55mph issue which would not apply to the front and sounds like you got that taken care of via rear axle resolution. I must have misread and thought you were experiencing new issue. It is funny how some of the different distuiquished issues are determined by common speeds, which is helpful in narrowing at least where to start looking. The dealer can also hook up a vibration analyzer on the powertrain components to distinguish the faulty area. Im pretty mechanically inclined and had my issue narrowed down to the front diff, was just a matter of convincing dealer. Since the wheels still turn on the truck, its not considered broken/faulty to them.

Posted

What you have described (tiny rumble strip feel) is your front differential. Needs replacement or complete overhaul. You may find this thread /post linked below more useful and related. This is not the resolution to all, but for those SPECIFIC to "tiny rumble strip" feel issues, its worth reviewing. We have several members (including myself) who got their dealerships (NOT EASY) to replace the entire front differential assembly, which resolved the issue and for most part trucks rode smooth as glass again.

 

http://www.gm-trucks.com/forums/topic/154976-2014-sierra-humming-noise/page-9?do=findComment&comment=1607902

Thanks for the link I will be checking that thread out . But I also have the rumble strip vibration with a slight harmonic like you were to have your windows down a certain way on some cars at speed and you get a very similiar sound . Although mine is between exactly 20 and 30 mph . Also for the record I have a 2wd so no front differential .

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Latest Articles

  • Posts

    • I will admit I haven't experimented much with pressure drops beyond the numbers I put in and part of that is that the numbers I used are fairly low and then found out it would trigger regardless at that 35 psi. Having said that I had tried before had changed the placard pressures and being that I have a 1 ton set to 80 on the placard for the rear I believe it triggered close to 60, the front I don't recall now for sure but thought maybe it could get close to 45 from that factory 60 placard pressure. So I never did figure out if it was a number of psi from placard pressure to the alarm or a percentage of the total placard number as some figured it was like a 25% drop from placard pressure would trigger it. So as to try and answer your question, I believe I set the placard pressure on the front to 47 or so and while I run the front tires at 40, they have dipped below that some if its colder and I haven't put "winter air" in yet and never once have had the front alarm go off. I would say that the answer your looking for is no, that if you set your placard pressure to 45, you have a certain amount of room to drop below that pressure before the alarm will go off.    The pressures you decide to run in your truck, that ends up being what makes sense to you based on what your carrying in your truck or if towing, then have to bump them back up to something that will carry the load in the rear and the fronts typically left at the same pressure. It all comes down to that chart I put the link to and using an accurate roadside scale to be your guide, both unloaded and then loaded to know your minimum safe pressures.    I just wish GM would allow a person to change the readings for the tire pressures to the English system of pounds as I have to look at that goofy metric reading that will never ever jive in my head and will go over and change it just to figure out what they are if need be and then change it back. 
    • That part I understand, that the dealer can do it. But I'm not understanding why updates that were available to the truck since it left the factory, or the dealership originally, would not still be available to it without dealer intervention.   I'm thinking along the lines of recalls. They stay available until they are completed. Why not updates as well, especially since some of those can be safety related also?
    • That's good to know, but I don't think I'll even be running them under 45 in the rear  unless it's on the sand or something but will only be for a short distance anyways!    I didn't read all the instructions in the booklet yet, but do you know let's say I set the rear psi on the placard to 45, will the warning light come on soon as it drops under 45 or is there a percentage it has to drop from the set value before the warning light is triggered?
    • That's bad.  Like, its probably destroying the stub axle the CV slides into.   Do you have a proper lift installed with differential lowering brackets?  Did you install AT4/Trail Boss factory CV axles?  
    • Hot? New Jersey? Today? I was working on my old 2000 Silverado 1500 today. Believe me, it was boiling hot today. As it has been.
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...