Jump to content

Shake or Vibration Issues

Silver space ship
 Share

Recommended Posts

abominable z71 Enthusiast

abominable z71

Posted
Posted

I have a question for all of the guys out here who are mechanically inclined. Would it be possible to remove the rear drive shaft put in in 4x4 and drive to eliminate drive shaft and rear end as cause of vibes. If still present, reinstall shaft, then take out front shaft to eliminate front shaft/diff as cause? I'm almost positive this can be done but not sure what you can use in rear of trans to stop spillage of atf and also front of transfer case. Any trans gurus in this thread?

It is possible but like mentioned above if you do it yourself you have to seal the rear out put otherwise the t-case pukes out transmission fluid. Not sure how you're supposed to seal it up to prevent this, maybe there is a special part GM has that replaces the stub shaft that slides into the transfer case. You could remove the stub shaft from the drive line by pressing out the u-joint and slide it back into the t-case but I don't see how you would prevent it from falling out without the drive line to hold it in that would really suck for it to fall out at 70mph on the freeway, for you and whoever is behind you on the road, it's designed to slide in and out as the suspension cycles so there is no keeper holding it in. The front drive shaft doesn't turn when in 2wd only the front CV shafts are rotating while in 2wd.

  • Replies 12.9k
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

csckickass
csckickass

Well folks, I did it. After all the failed attempts at the Chevy dealer I traded it in for a 2015 Ram 1500 Larame. I have to agree with the other folks on here that have done the same thing, it was th

mafd2
mafd2

Apparently you and the other customer reps don't care. If you or GM would care y'all would put more effort in the matter. Just coming on the forum and stating the same repetitive posts and being a 3

DALaws
DALaws

Well I have some good news and bad news about my truck vibrations. Good news is that my truck has a significantly less vibration at speed. The bad news is my truck has significantly less vibration. Fo

Posted Images

14silverado4.3 Enthusiast

14silverado4.3

Posted
Posted

The truck went back to tire shop today to reestablish balance, confirmed had some tires a little bit off so we trued them up again. While there, I asked can we get it up on a lift and get all tires rolling at once, we did and nothing looked bad in the driveshaft or wheel assemblies.

 

Drove into work this morning, tire vibration is better but there is still something there.. I am thinking something in torque converter... as soon as you crest a hill and plane out with little throttle input the truck has some "shuddering", full throttle no problems...

Richard Fisher New Member

Richard Fisher

Posted
Posted

After chasing the elusive vibration issue with my 2015 Sierra crew cab short bed for most of a year, I finally expanded my search. My truck had been lowered with long shackles and shocks in the rear and a drop spindle kit in the front which did not cause my vibration issue. It also did not change the issue and I had decided to just live with it until I blew the drive shaft somewhere north of 95 mph. Lucky for me the truck had been lowered so the rear part of the drive shaft just skipped along the road surface. Now for what appears to be the fix that works for me. I found CALVERT Racing of California and got a set of Caltrac 3400's installed after making sure the pinion angle and drive line were all in specs, about 1 degree negative pinion. This seems to be the best $400.00 ever spent. No shake, No rattle, No role, No vibration all the way up and down; 0 to 112 mph anyway and no ill ride effects. The ride seems to be tighter and totally stable at all speeds. Total cost for me was about a grand and has a warranty. As far as I'm concerned GM should put Caltracs on all of their Silverado and Sierra 1500 pickups. They could probably do it for no more than a $300.00 price change out the door and make a lot more people happy.

.

  • Like 1
trik396 Enthusiast

trik396

Posted
Posted (edited)

So you are saying that your pinion angle was off? Or do you think your original driveshaft was bent or out of balance?

Edited by trik396
Richard Fisher New Member

Richard Fisher

Posted
Posted

The original drive shaft was bad from the factory and the pinion angle was off by one degree. Replacing the drive shaft and correcting the pinion angle both did not stop the vibration. After installing the Caltracs, the vibration is gone. I don't much care what it took to correct the problem. Just came back from a drive that gave me the opportunity to get up to about 107mph and no vibration problems. It does make a slight clunk when crossing rough ground though.

trik396 Enthusiast

trik396

Posted
Posted

Old drag racer here. Familiar with cal tracs. Also if I remember correctly you need minus 2 to 3 degrees of neg pinion. But I have no clue what specs are for our trucks

Darth_Vader Enthusiast

Darth_Vader

Posted
Posted

Old drag racer here. Familiar with cal tracs. Also if I remember correctly you need minus 2 to 3 degrees of neg pinion. But I have no clue what specs are for our trucks

 

Think they are saying 1 degree now for street vehicles, still 2 to 3 for drag racing.

 

Oddly enough I ordered my set of Caltracs earlier today, for different reasons mainly but also because now that I have gotten my vibration fixed I have noticed some pinion angle vibrations during coast or cruise that go away with heavy load.

trik396 Enthusiast

trik396

Posted
Posted

Can anyone tell me where I can find information on what correct pinion angle should be?

Can anyone tell me where I can find information on what correct pinion angle should be?

Can anyone tell me where I can find information on what correct pinion angle should be?

Wrench589 Enthusiast

Wrench589

Posted
Posted

Check out this video....

 

 

 

I had no idea there was so much wind-up of the axle housing with a leaf spring suspension! With that much angle change, how does any truck not vibrate like crazy? I would imagine the previous generation did the same thing...why no vibs there? Makes me wonder how import pinion angle really is on most vehicles.

trik396 Enthusiast

trik396

Posted
Posted

Pinion angle is important. Yes it changes with a heavy load or hitting bumps etc but it has a range of motion that it works thru and as long as it's within spec it is smooth. If it's off from the start it doesn't work right and you can have problems with u joints and vibrations

2strokesmoke Enthusiast

2strokesmoke

Posted
Posted

Frame beaming is the real culprit, along with stiffer body mounts this generation truck, allowing vibrations from engine, and driveline into the cabin and steering wheel.

 

Shame on you GM.....!

 

Solutions that will help.

Balance your driveshaft, confirm run out at axle hubs, sell your oem tires buy good brand name quality ones. Run 18" rims

Add some dampening melt sheets under your carpet on the floor, this and softer body mounts will reduce these crapola problems. A good test is to clamp angle iron many c clamps or f clamps to frame and retest your vibrations.

If your vibration intensity changes you have confirmed GM's known problem!

 

Good luck

67ChevyRedneck Enthusiast

67ChevyRedneck

Posted
Posted

Proof that it is a frame resonance issue that can't be pinpointed?

 

 

The Silverado will ride on an all-new frame, but the truck’s basic setup—separate body and frame and a live rear axle located by leaf springs—isn’t going to change, nor will the usual choice of standard rear-wheel drive and optional four- or all-wheel drive.

 

http://www.caranddriver.com/news/2019-chevrolet-silverado-1500-spy-photos-news?src=ha_m&mag=cdb&dom=fb

 

I find it hard to believe GM would be doing an "all new" frame after only a 5-6 year run.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • dna9656
      New to Me 2010 SLE (Quirks, Issues)

      By dna9656 · Posted

      Your tire pressure issue may just be batteries, you can reset them using tge Ing switch (I think) and the owner's  manual. ChatGTP will b e a faster, better help than Google.
    • Another JR
      Towing In Loose Gravel

      By Another JR · Posted

      The thinking is that starting out in a higher gear makes it easier to avoid applying excessive torque when pressing the gas pedal. In a modern 4wd truck with 4 low and a limited slip or locking rear end, I would use 4 low and try to crawl up the ramp. Sometimes if they are too slippery, you have to back up to let the boat have some bouyancy, and then accelerate briskly to get some momentum to help you pull the through the slippery parts. 
    • XY74
      Roll up bed cover experiences

      By XY74 · Posted

      I have a Retrax pro that I first had on my 2020 chevy and transferred it to my current GMC.  It stays in the garage most of the time, so hard for me to judge it's long term weather resistance.  It still works perfectly, been very durable.  It doesn't see oil patch usage, but it's not a mall queen.  It keeps most things mostly dry (small leaks) and the security of it is enough to slow someone down but not keep them out for long.  I would buy one again, it works for me.     
    • fm2176
      New to Me 2010 SLE (Quirks, Issues)

      By fm2176 · Posted

      Thanks to the convenience of Amazon, I was able to get a few things done to the truck today.  I installed Carquest Premium oil and air filters with five quarts of Mobil1 High Mileage 10-30 along with a quart of Pennzoil Platinum 5w-30 I already had.  The latch for the flip up center console lid was broken so I replaced it along with the power mirror switch.  I found my push retainer assortment this morning and reattached the plastic under the bumper and it was only held on with a few screws and retainers.  Then I programmed a new remote keyless entry fob so I can lock my dog in the truck when I take her out with me (I've got to keep the air going for her since it's been in the 100s).  Finally, I ordered some LED interior bulbs and replaced the reading lamps.  The front lights are working fine while one of the back lights only works intermittently and the other not at all.   While under the truck, I found the source of at least one of the noises: the sway bar links need replacing.  I ordered a set of Suspension Dudes links with Code Red bushings.  Never heard of them, but they're made in the USA and have decent reviews.  While making yet another Amazon order, I went ahead and added a set of front tow hooks.  I went with red, since that's the color of the sway bar link and bushings and it should look decent enough on a black and chrome truck.  Speaking of which, it doesn't bug me much, but the passenger side mirror has a chrome cap while the driver side doesn't, so eventually I'll make them match one way or another.  Oh, and I ordered a $20 TPMS reset tool.  No idea if it will do anything for my sensors but it was cheap and will work for the Ford Transit Connect as well.     For tradition's sake, I ordered a new oil change wrench.  I kept the Snap-On 9/16"x15mm GM wrench I bought when I was 18 in the 2006 GMC from the time I bought that truck until the truck was lost.  While I was tempted, there's no need to spend $80 for a new SO wrench, or even $50 with shipping for a used one on Ebay.  I just bought a Duratech 15mm extra-long ratcheting wrench to do the job as needed.  It works, and if I like that wrench enough, I'll buy the set.  
    • Another JR
      Multigate electrical problem

      By Another JR · Posted

      The recall is for exactly this issue - those drain holes combined with the limited environmental capability of the tailgate electronics card inside the tailgate were a problem. The “safety issue” was the potential for the tailgate to spontaneously open, but all kinds of tailgate misbehavior can occur from water contamination of that control card.    There is no real fix yet. The initial recall just disabled the tailgate. Later, when parts became available, they would replace bad parts with new parts of the same bad design. My dealer is going nuts because the few times I let them get their hands on my truck, my tailgate is off due to a slide-in camper installation. They really want to cut my tailgate wires, but I won’t give them the chance. I will let them get their dirty hands on it when a real fix (redesign) is available.  My tailgate, which works just fine with sealant plugging the drain holes, will remain safe in a dry storage crate until then.  

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...