Jump to content

2019 GMC Emblem Installation

Rudger

By Rudger
in Modifications, Wheels & Tires

 Share

Recommended Posts

Jmonty Enthusiast

Jmonty

Posted
Posted
10 hours ago, quicksilverc5 said:

The wheels are the gloss black wheels that normally come on an elevation.  But I have BFG K02s instead.

 

RD3 Wheels, 20" x 9" (50.8 cm x 22.9 cm) Black gloss painted aluminum

 

2019 Wheel RPOs attached

2019 Wheel RPOs.pdf

Man looks sharp! What size K02 are you running?

  • Replies 47
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

Rudger
Rudger

Hey all,   I installed the OEM black GMC letters on my AT4 this weekend and thought I would pass this shortcut along.  If you don't mind being a bit destructive and want to take the easy rou

quicksilverc5
quicksilverc5

I did mine the hard way, which the front grill removal is a B$%#.  Looks sweet though.  The rears are easy with a heat gun and masking tape.  A little harder since all the letters are the same.  Since

joshuapchase
joshuapchase

Thank you for your help! I just replaced my letters with the black... aside from some issues getting the new clips to “click” it was a rather painless experience! Pretty happy with the results...

Posted Images

quicksilverc5 Enthusiast

quicksilverc5

Posted
Posted
18 hours ago, Z71-K9 said:

Where does one purchase the black emblems?

Any GM Parts site..

 

Front and Rear GMC Emblem in Black for Vehicles with MultiPro™ Tailgate
Part No. 84364354

 

Front and Rear GMC Emblem in Black (without the Multipro)
Part No. 84364356
joshuapchase Enthusiast

joshuapchase

Posted
Posted
On 2/3/2019 at 8:02 PM, Rudger said:

Hey all,

 

I installed the OEM black GMC letters on my AT4 this weekend and thought I would pass this shortcut along.  If you don't mind being a bit destructive and want to take the easy route - just pry the red insert off of the factory emblems and it exposes the retaining clips.  Insert a screw driver and they pop right off.  No grill removal required.  I had one or two tangs that didn't immediately snap back in on the new emblems.  apply a bit of pressure to the grill tab with either your finger or a flat blade screw driver from behind until it clicks.  You are good to go.

 

 

20190202_151922.jpg

20190202_151932.jpg

20190202_151938.jpg

20190202_151941.jpg

Thank you for your help! I just replaced my letters with the black... aside from some issues getting the new clips to “click” it was a rather painless experience! Pretty happy with the results...

132D1ADF-BF11-42A4-A306-FD340DC1C247.jpeg

  • Like 1
  • 1 month later...
BringTheRain403 Senior Enthusiast

BringTheRain403

Posted
Posted
Hey all,

 

I installed the OEM black GMC letters on my AT4 this weekend and thought I would pass this shortcut along.  If you don't mind being a bit destructive and want to take the easy route - just pry the red insert off of the factory emblems and it exposes the retaining clips.  Insert a screw driver and they pop right off.  No grill removal required.  I had one or two tangs that didn't immediately snap back in on the new emblems.  apply a bit of pressure to the grill tab with either your finger or a flat blade screw driver from behind until it clicks.  You are good to go.

 

 

20190202_151922.thumb.jpg.6d1c264a544a47899bc388678c178da5.jpg

20190202_151932.thumb.jpg.7bb09ab6759a501cb1808e753d18b79a.jpg

20190202_151938.thumb.jpg.fea935f842a342140ece708aeafb7d8d.jpg

20190202_151941.thumb.jpg.2a8f3df82c7d32e38af02a14532fca54.jpg

BTW the way you did this is the way GMC instructs their techs to do this. I have the official GM instructions and I can scan them and post them here if anyone would like to see them...

 

Sent from my Pixel 2 XL using Tapatalk

 

 

 

rmkmb Enthusiast

rmkmb

Posted
Posted
4 hours ago, BringTheRain403 said:

BTW the way you did this is the way GMC instructs their techs to do this. I have the official GM instructions and I can scan them and post them here if anyone would like to see them...

 

Sent from my Pixel 2 XL using Tapatalk

 

 

 

Can you post them,would be appreciated

  • 1 month later...
Canadian AT4 Guy New Member

Canadian AT4 Guy

Posted
Posted (edited)

Does anyone know where I can find solid black metal or plastic GMC emblems for the grill and tailgate?  Id prefer metal. I don't want the chrome outlining the emblem. I can't find anything and or not sure if it will fit as most are listed as 2015-2019. I have a 2019 AT4.

 

The link below i'm not sure about?

 

Thoughts?

https://www.ebay.com/itm/254231917725

Edited by Canadian AT4Guy
  • 1 month later...
  • 4 weeks later...
  • 4 months later...
cvklok Enthusiast

cvklok

Posted
Posted

I initially attempted the long way of installing these emblems..... I abandoned that mess when I seen this post.  Using this technique is the way to go, makes it a 10 minute job to change out the front GMC emblem.  Thanks for the help!

Jim E Enthusiast

Jim E

Posted
Posted
On 9/1/2019 at 9:16 PM, Danny's AT4 said:

How do you change out the letters on the tailgate? 

 

They are stuck on.  Heat gun or let it sit in the sun are the usual options.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • AlVeron
      Manufactuer's Defect - Paint Failure - Cherry Red High Country 2021 Suburban

      By AlVeron · Posted

      This is NOT impact damage nor neglect. There were previous class action lawsuits because of such paint preparation st GM manufacturing plant. Not just the Cherry Red Color. This paint is applied in three processes to obtain the desired color.  The manufacturer will cover for 36 months or 36k miles only. That rust is actually corrosion because of the paint process failure. Corrosion is covered for 100,100 miles or a certain months. However their corrosion doesn't include this type. Go figure. Clearly manufacturer knew from previous paint issues. This started 3 weeks ago out of the blue.  
    • richard wysong
      Wow I'm in a pickle. (Broke down truck) and a story.

      By richard wysong · Posted

      Is it time to put a piece of tape over the CEL? 
    • davester
      2015 Silverado 3500 right rear turn indicator failure

      By davester · Posted

      consider doing electrical testing?  I would guess some power or ground wire/connection has a problem.   alldata.com has wiring diagrams, connector pinouts and diagnostic procedures you can use to find where the problem is.
    • davester
      My First Project and GMC has me stumped

      By davester · Posted

      can you tell if the reader is actually trying to get codes, and the pcm is reporting none, or is your reader just silently failing because it's not communicating with the pcm?
    • Atlas
      Wow I'm in a pickle. (Broke down truck) and a story.

      By Atlas · Posted

      Any joy with this truck seems to be short-lived.   The CEL for P0172 ("bank 1" too rich) is now "intermittent".   I'm not sure where to check, or re-check, and my energy to keep chasing problems with junk is wearing thin. The P0172 seems to set as I'm coming to a stop, completely off the throttle, when fully warm. At least, that's what it's done the 3? times it's set.   Everything appears normal on the scanner EXCEPT long term fuel trim. There's only one bank on this vehicle because it's an OBD 1.5 with only one upstream O2 sensor. At idle, it's around -16.4% and will dip to -18% occasionally at idle or off-throttle. LTFT approaches 0 when throttle is held at 2500rpm. Short term appears normal, much closer to zero all the time. The LTFT tells me the engine is running rich at idle but compensating at higher load. But, why?   The EVAP purge valve doesn't appear to be leaking/sucking fuel vapor continuously. Is it sticking just as I come to a stop and the engine is choking on fuel vapor and sets the P0172? But that doesn't explain the persistently negative LTFT. Disconnecting the purge valve doesn't seem to make any difference.   I suppose that leaves another dang issue with the fuel injector. A leaking fuel pressure regulator, a new leak in the spider, or a leaking fuel injector/poppet valve I didn't see, or a small crack in one of the spider legs.   The vacuum line leading to the fuel pressure regulator doesn't have raw fuel in it. It doesn't even smell like fuel when it's pulled off, not until you suck air through it, then you can tell it leads to a fuel component. I'd consider that normal? Nothing is signaling this is a FPR issue from the outside, at least.   The oil smells like fuel but it's not building volume. I've noticed most oil in most engines smells like fuel to some degree so it's hard to say if the smell is an issue or not. Or if the engine just still smells like fuel because the crankcase was full of it a few hundred miles ago. But it's been changed twice since that original issue of the leaking fuel line dumping fuel into the intake.   Patience is running very thin. Every win seems to be accompanied by two steps backwards, or another issue that leads to removing at least the top half of the intake manifold. Enough! LOL

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...