Jump to content

Shake or Vibration Issues

Silver space ship
 Share

Recommended Posts

tbarn Senior Enthusiast

tbarn

Posted
Posted

Hate to be the bearer of bad news but there is no motor mount recall. A newer tsb for loosening the the mounts and adjusting the motor then retightening in a specific sequence is available. It is possible that a tech called TAC and was given a new motor mount p/n but I haven't heard of that yet.

  • Replies 12.9k
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

csckickass
csckickass

Well folks, I did it. After all the failed attempts at the Chevy dealer I traded it in for a 2015 Ram 1500 Larame. I have to agree with the other folks on here that have done the same thing, it was th

mafd2
mafd2

Apparently you and the other customer reps don't care. If you or GM would care y'all would put more effort in the matter. Just coming on the forum and stating the same repetitive posts and being a 3

DALaws
DALaws

Well I have some good news and bad news about my truck vibrations. Good news is that my truck has a significantly less vibration at speed. The bad news is my truck has significantly less vibration. Fo

Posted Images

pm26 Senior Enthusiast

pm26

Posted
Posted

PAGE 201 !!! Has to be a record.

Especially with these vibration problems being so rare on these trucks! :rolleyes:

  • Like 2
14GFXSilverado Enthusiast

14GFXSilverado

Posted
Posted

Hey guys. Just wanted to throw in my two bits. I was having major vibration issues on my truck at certain speeds sometimes at 50km then 80 and 110km. I had discussed with the dealer about this and they had looked everything other on a couple occassions and told me nothing was wrong then finally one of the service techs had come out and asked me if I would be interested in trying out different rims/ tires on my truck (looked like he had a theory in mind) so i did. I originally had the 20's on the truck and we had swapped for the 18's instead. similar diameter only approx .37" difference. I drove the truck right away after the swap and no vibration. been driving it for the past two weeks this way and still have not come across any vibration. I had made the dealer buy my 20's back off of me and give me a credit to keep the 18's. The mech had said that he noticed a lot of the trucks that did complain about vibration had the 20's on them and he figures something is off. Either way I am just putting in my story of what happened. For others here on the site that have further vibrations issues I hope they get solved and if I here more then I will post it.

Silver space ship Enthusiast

Silver space ship

Posted
  • Author
Posted

PAGE 201 !!! Has to be a record.

 

 

When I started this post I thought I might be the only one, and know body will believe my thinking I was just trying to stir the pot. I had know idea if others where having issues. Sadly I never thought it would have turned into this.

keakar Enthusiast

keakar

Posted
Posted (edited)

Man , You could churn butter in that thing. I have only had mine on interstate maybe three times. Not as bad as yours. I can see the bottle spinning. :omg:

but that's normal, just the way trucks are supposed to ride

 

GM designs its vehicles to ride that way, everything is normal

 

every single truck on the dealers lots drives and vibrates the same way so its normal

 

why don't we accept it when they tell us this :bs:

 

great video and mine does it about the same at times and sometimes not as bad

Edited by keakar
Ironhead2 Enthusiast

Ironhead2

Posted
Posted

Hope I can get my 50k vibrator fixed , or replaced ,buy back, trade for ??? Very sick feeling in my stomach.

  • Like 1
eb575757 Enthusiast

eb575757

Posted
Posted

2014 Z71 2WD

 

i have the vibration shakes like everyone else and i bought a new set of rims 17" for the stock tires, same shake. Took it to the shop i bought the rims from twice and no better. I then bought new rims and tires 22" and shake still there at 35 to 45 and again at 74mph. Took it to the dealer and they noticed it and gave me a rental for 5 days. I went back and they said the problem was my aftermarket rims and tires. I also felt it in the rental. Tried to put up with it was a couple weeks but driving me nuts.Called and talked to the service manager, he said there is a know issue but no fix. He then said he wants to check my rims and tires again and put stock ones on and see if it still shakes. really!!! So i made another appointment but not for two weeks. He said they are very busy with other recalls. Plus he is getting the regional service manager with some vibration detector.

I also noticed that there are no 2015 1500 silverados out yet at least around here, is GM making sure they are ok or anyone else know?

Spurshot Senior Enthusiast

Spurshot

Posted
Posted

Has anyone that has this issue on a 4wd tried to drive it with the rear driveshaft removed to test for the vibration?

fondupot Senior Enthusiast

fondupot

Posted
Posted

Has anyone that has this issue on a 4wd tried to drive it with the rear driveshaft removed to test for the vibration?

 

Please dont give anyone any ideas....this doesnt seem safe.

tbarn Senior Enthusiast

tbarn

Posted
Posted

Has anyone that has this issue on a 4wd tried to drive it with the rear driveshaft removed to test for the vibration?

Thought about that last winter. Never came up with a way to seal the output shaft of the transfer case.

ToesonTheNose Enthusiast

ToesonTheNose

Posted
Posted

i'll say this, I don't drive a lot. my truck sits on the driveway for a week at a time and sometimes it goes a month without being driven. I mostly use the car or motorcycle and the truck gets used mostly just for pulling the boat and this has been my pattern of truck use for nearly 35 years.

 

that said in the entire 35 years I have NEVER had any vibration or feeling of flat spots on the tires, if there was any it was so negligible that it went unnoticed completely.

 

I will concede there might be the possibility of ever so slightest of flattening of the tire from not moving in a while but this it corrected before you leave the driveway with a few revolutions of the tire. I had my truck parked in the driveway for 8 years and never moved while recovering from health issues and when I finally took it for a drive the tires were perfectly smooth as always even though it needed new rotors and brakes from rusting in the driveway. if flat spotting EVER had a chance to be a problem then I think after 8 years it would have occurred but it didn't so I dismiss you notion with the concession that it may occur at some small minor unnoticeable level that cant be noticed or detected or used as an excuse for causing vibrations

 

the ONLY type of flat spot you would feel in the tires is if it gets dry rotted and harden that way and this type of flat spotting never goes away.

 

the notion that a brad new tire can have noticeable flat spots to cause it to be felt when driving is laughable on its face and insulting to anyone who has ever owened a motor vehicle. maybe someone who just fell off the turnip truck might believe such malarkey but as a wise man once said "don't pee down my back and tell me its raining"

 

 

I can feel the crosshairs of a liberal nut jobs rifle scope on me at this very minute lol.

This right here, I deploy 6-7 months at a clip, my vehicle doesnt move during that time, not once did I ever have a flat spot issue in 11 yrs of deploying

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • Gkistler
      2015 Sierra Denali L86 cyl 5 misfire at idle

      By Gkistler · Posted

      Hi friends - first time poster. I have a 2015 sierra Denali with 150k miles, I’m the second owner and she’s given me 75k of great service. I run a pulse AFM disable device. Starting Thursday when I exited the freeway after a short local ride it started idling rough, with an obvious misfire shake and was down on low end power.  I got it home and hooked it up to my scannner and found no codes but in live data a pretty bad misfire on cylinder 5. I replaced the coil, plug and wire with all new OE replacements (Delphi gn10165 coil, acdelco wire and 41-168 plug). It’s still behaving the same way after firing the parts cannon at it.   I know cyl 5 is a non AFM cylinder so I am not thinking this is AFM related but I’m kinda at a loss. injector? Bent pushrod? It’s running too well over 1k rpm to suggest those IMO. Has anyone chase this issue before and what was it? Any suggestions? 
    • zibzer2
      Pulsating Noise 4Cyl Mode

      By zibzer2 · Posted

      2017 Silverado L83 5.3l 6speed transmission Hello, not a new member but havent posted in a while and my old signup info isnt working so had to create a new account. anyways, I have an issue with my truck and hope someone can spread some light on whats happening: -when it goes to 4cyl mode it makes a clunk sound (but not when coasting or going downhill) -when in 4 cyl mode and under load it makes a load pulsating sound (not a tick). -goes away completely when in M5 gear or when plugging in an AFM delete. Im guessing it is one of 2 things but im not convinced of either to be honest. 1. lifter stuck in v8 mode 2. torque converter shudder realistically it doesn't seem like the TC as there is no physical vibration , and it never happens in v8 mode. but maybe? and wouldnt a lifter make a sound whether with load or not? any ideas let me know please. thank you!  
    • Chuck FB
      Some Assembly is Required

      By Chuck FB · Posted

      Which has made me wonder with the various engine failures of a few brands in the last few years, is it sub par materials such as lifters etc causing failures, or bearing clearances on the crank etc or perhaps bad designing of an engine physically or causing too much load on the components due to the hp/torque they can push out of them. Or is the oil viscosity and additive package of current oils or a lack of oil flow by an oil pump not able to supply sufficient oil at idle or under high load at low rpm. Or is it every item I listed that combined together has pushed the limits so far to the left that there is hardly a margin of safety left and add in some fuel dilution and too long of an OCI and premature engine failure is the result ?. 
    • Grumpy Bear
      Some Assembly is Required

      By Grumpy Bear · Posted

      He is not saying that an SAE *W20 will have more viscosity than a *W40 due to MORE VII polymers. He is saying that although multiple *W40 may post in the PDS the same or similar 100 C and 150 C viscosities that the blenders choice of modifier TYPE and AMOUNT to get his chosen base to grade will not give identical real world viscosities in shear and at temperature. All will pass the SII test but not all will pass the 100 C HTHS (unpublished value) testing the blender does and relies on to get the required by law "percentage improvement' referenced to his last great work.    Tis the problem with the lie. Once told others are required to support it. 
    • PunchT37
      Parking Brake - Automatic Engagement Questions

      By PunchT37 · Posted

      I have a `25, 1500 that auto sets on incline. Never knew that at first. I have the electronic shifter. Just think if it didn`t do that? Unlike a mechanical shift that you can muscle out of park, how would you get this thing out? That would be a problem.   What I found out later is, I don`t have to push the button to release. Just put it in gear.   Setting parameters? Don`t know if it`s possible.

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...