Jump to content

Leveling with Bilstein 5100

agraves138
 Share

Recommended Posts

makosenna Enthusiast

makosenna

Posted
Posted

Just ordered a set of 5100's from 4 Wheel Parts @ $375.00 total to my door. I may set it at 2 .075 or 3 1.26.

NCM_1801.JPG

  • Replies 60
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

crushNchowda
crushNchowda

FWIW I have Bilstein 5100's all 4 corners top setting in front w/ 33" 275/60R20 Nitto Terra Grapplers + 2.25" (+1") rear blocks. My total before/after ride height for the front was a hair over 2.5"...

2016LTCC
2016LTCC

I like this look. Would you say the ride is better unloaded around rough town/city driving? Also, have you noticed any difference in wear on your front tires?

Kubs
Kubs

I also installed Firestone Ride Rite air bags to keep the truck level when towing.  Its rides great loaded or unloaded.   IMG_20180601_140227534_HDR[1] by Mike Kubiak, on Flickr

Posted Images

Ozer Enthusiast

Ozer

Posted
Posted

^ Why even get those for lifting then, you may not even notice 3/4 inch lift. Set it to 4 and you will still have some rake. Unless you tow often.

 

And guys, remember to aim your headlights down when you level. An overlooked last step :)

  • Thanks 1
MN1(SW) Enthusiast

MN1(SW)

Posted
Posted

Mine are either on the 3rd or 4th highest notches.  I can't remember, It's been a couple of years since I did it and my truck's been in storage since shortly after.

20160220_141628-min.jpg

  • 1 month later...
sammiller86 Enthusiast

sammiller86

Posted
Posted
On 8/23/2018 at 12:35 PM, Kubs said:

I also installed Firestone Ride Rite air bags to keep the truck level when towing.  Its rides great loaded or unloaded.

 

41693217835_85569b6c78_k.jpgIMG_20180601_140227534_HDR[1] by Mike Kubiak, on Flickr

When did you install the airbags? I just installed the 5100's on the 3rd setting because tow frequently at times (depends on the time of year). I knew going j. I was going to have to do something to the rear end for towing. I have been debating airbags or just throwing an Add a leaf on instead. I live in NY ask the winters can be harsh sometimes and I'm just worried about airbags having problems in the snow/cold etc. 

 

Kubs Enthusiast

Kubs

Posted
Posted
On 10/10/2018 at 8:05 PM, sammiller86 said:

When did you install the airbags? I just installed the 5100's on the 3rd setting because tow frequently at times (depends on the time of year). I knew going j. I was going to have to do something to the rear end for towing. I have been debating airbags or just throwing an Add a leaf on instead. I live in NY ask the winters can be harsh sometimes and I'm just worried about airbags having problems in the snow/cold etc. 

 

I just bought the truck in April and installed the bags in May.  I have not driven through snow with them yet.  If you tow frequently though it is a good investment.  Firestone makes good quality rubber air bags.  I doubt it will be an issue in winter up here.

pronstar Enthusiast

pronstar

Posted
Posted

Just about very modern large truck, and many trailers, runs airbags.

I wouldn’t worry about winter weather, they’ve been proven to work in all weather conditions.


Sent from my iPhone using Tapatalk Pro

sammiller86 Enthusiast

sammiller86

Posted
Posted

Where do you guys mount the schrader valves? I'm going to stick with the manual inflation until I can save up some money for the onboard compressor in the spring probably. I was thinking of mounting them in the gas cap to keep them away from dirt/snow people's feet etc so they are protected? Is there enough room in there for both valves?

Kubs Enthusiast

Kubs

Posted
Posted
22 minutes ago, sammiller86 said:

Where do you guys mount the schrader valves? I'm going to stick with the manual inflation until I can save up some money for the onboard compressor in the spring probably. I was thinking of mounting them in the gas cap to keep them away from dirt/snow people's feet etc so they are protected? Is there enough room in there for both valves?

I use my valves to hold the license plate on.

 

42063005032_c120c5ee8b_k.jpgIMG_20180511_180815496 by Mike Kubiak, on Flickr

  • 1 month later...
makosenna Enthusiast

makosenna

Posted
Posted

5100's working well so far... good ride no rub and no big drop in mpg's.

Added bed cover a few weeks back to keep cargo dry.

untitled.png

goeb34 Enthusiast

goeb34

Posted
Posted
5100's working well so far... good ride no rub and no big drop in mpg's.
Added bed cover a few weeks back to keep cargo dry.
untitled.thumb.png.dea3ee886fcd3b8982eb7fa3b50b8bda.png

Which notch is this set on
crushNchowda Senior Enthusiast

crushNchowda

Posted
Posted (edited)
On 8/23/2018 at 7:39 AM, Paul_Aris said:

I tow so has anyone gone on the tallest notch on the front and 1 up from stock on the rear? Wonder what that would be like height wise and when towing? Or it appears the rears ones may not be adjustable. 

 

FWIW I have Bilstein 5100's all 4 corners top setting in front w/ 33" 275/60R20 Nitto Terra Grapplers + 2.25" (+1") rear blocks. My total before/after ride height for the front was a hair over 2.5"....so either the bilsteins @ top setting are really more like 2" or the tires are a little taller or combo of both. I run 44 psi front 42 rear.

 

I had 2200 lbs of rocks in the bed w/ this setup & it did not appear nose high, it still looked level - that isn't apples to apples to towing a trailer, but I think if you're not maxing it out you'll still have a level ride height may even maintain some rake depending on tongue weight.

 

Here are some pics w/ this setup (no weight in the bed though) - its tough to really see the amount of clearance added w/ the thick stock running boards, but its significant & really is the perfect stance for this generation of GM 1/2 tons IMO. I removed the front chin spoiler/air dam/diffuser (whatever you wanna call it) & that really added to the "lifted" look of the trucks stance, also improved overall clearance, I noticed MAYBE 1/2 mpg difference on the highway, although that could also be attributed to the height increase in general. 

 

Actually, I think running 275/65R20's would be the PERFECT look/height, except you can't get a non-LT 8+ply AT tire in that size & I didn't like the drop in acceleration/braking/MPG performance w/ the heavier LT tires so decided to stick w/ the 275/60R20 Nittos.

 

Lastly - 2 pieces of advice, #1 if you get these shocks I'd hit em up w/ some spray can clear coat before installing so they stay nice looking, they have stainless steel body but is 400 series & will oxidize in salty road conditions. #2 - if I were to do it all over again I would look into Eibach's setup as well - they are American made quality shocks & they offer a similar adjustable gas charged shock but also offer it w/ matching front springs (for a lil more $$$). I am satisfied w/ the Bilsteins though & will probably replace them w/ the same model once they're worn out - I have over 50k miles on them so far though & still ride like they did when new.

 

nitto2.png

nittos11.png

Edited by crushNchowda
  • Like 1
  • Thanks 1
makosenna Enthusiast

makosenna

Posted
Posted
On ‎11‎/‎24‎/‎2018 at 1:32 AM, goeb34 said:
On ‎11‎/‎24‎/‎2018 at 1:32 AM, goeb34 said:

Top setting.
Which notch is this set on


Which notch is this set on

 

  • 1 month later...
goeb34 Enthusiast

goeb34

Posted
Posted

Where is everybody getting their bilsteins from? Puttin the tax money to good use of em and some trail graps

2kwik4u Enthusiast

2kwik4u

Posted
Posted

Does anyone have the 5100 shocks and have them set on the "stock" setting? I have no desire to level or raise the truck at all. I have a strong desire to dump the POS Rancho shocks that are entirely too stiff for this vehicle.

Grjfer Enthusiast

Grjfer

Posted
Posted
14 hours ago, 2kwik4u said:

Does anyone have the 5100 shocks and have them set on the "stock" setting? I have no desire to level or raise the truck at all. I have a strong desire to dump the POS Rancho shocks that are entirely too stiff for this vehicle.

If you are just looking to replace the stock shocks I'd suggest the Bilstein 4600's. Per Bilstein they have the same valving minus any lift capability. 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • dna9656
      New to Me 2010 SLE (Quirks, Issues)

      By dna9656 · Posted

      Your tire pressure issue may just be batteries, you can reset them using tge Ing switch (I think) and the owner's  manual. ChatGTP will b e a faster, better help than Google.
    • Another JR
      Towing In Loose Gravel

      By Another JR · Posted

      The thinking is that starting out in a higher gear makes it easier to avoid applying excessive torque when pressing the gas pedal. In a modern 4wd truck with 4 low and a limited slip or locking rear end, I would use 4 low and try to crawl up the ramp. Sometimes if they are too slippery, you have to back up to let the boat have some bouyancy, and then accelerate briskly to get some momentum to help you pull the through the slippery parts. 
    • XY74
      Roll up bed cover experiences

      By XY74 · Posted

      I have a Retrax pro that I first had on my 2020 chevy and transferred it to my current GMC.  It stays in the garage most of the time, so hard for me to judge it's long term weather resistance.  It still works perfectly, been very durable.  It doesn't see oil patch usage, but it's not a mall queen.  It keeps most things mostly dry (small leaks) and the security of it is enough to slow someone down but not keep them out for long.  I would buy one again, it works for me.     
    • fm2176
      New to Me 2010 SLE (Quirks, Issues)

      By fm2176 · Posted

      Thanks to the convenience of Amazon, I was able to get a few things done to the truck today.  I installed Carquest Premium oil and air filters with five quarts of Mobil1 High Mileage 10-30 along with a quart of Pennzoil Platinum 5w-30 I already had.  The latch for the flip up center console lid was broken so I replaced it along with the power mirror switch.  I found my push retainer assortment this morning and reattached the plastic under the bumper and it was only held on with a few screws and retainers.  Then I programmed a new remote keyless entry fob so I can lock my dog in the truck when I take her out with me (I've got to keep the air going for her since it's been in the 100s).  Finally, I ordered some LED interior bulbs and replaced the reading lamps.  The front lights are working fine while one of the back lights only works intermittently and the other not at all.   While under the truck, I found the source of at least one of the noises: the sway bar links need replacing.  I ordered a set of Suspension Dudes links with Code Red bushings.  Never heard of them, but they're made in the USA and have decent reviews.  While making yet another Amazon order, I went ahead and added a set of front tow hooks.  I went with red, since that's the color of the sway bar link and bushings and it should look decent enough on a black and chrome truck.  Speaking of which, it doesn't bug me much, but the passenger side mirror has a chrome cap while the driver side doesn't, so eventually I'll make them match one way or another.  Oh, and I ordered a $20 TPMS reset tool.  No idea if it will do anything for my sensors but it was cheap and will work for the Ford Transit Connect as well.     For tradition's sake, I ordered a new oil change wrench.  I kept the Snap-On 9/16"x15mm GM wrench I bought when I was 18 in the 2006 GMC from the time I bought that truck until the truck was lost.  While I was tempted, there's no need to spend $80 for a new SO wrench, or even $50 with shipping for a used one on Ebay.  I just bought a Duratech 15mm extra-long ratcheting wrench to do the job as needed.  It works, and if I like that wrench enough, I'll buy the set.  
    • Another JR
      Multigate electrical problem

      By Another JR · Posted

      The recall is for exactly this issue - those drain holes combined with the limited environmental capability of the tailgate electronics card inside the tailgate were a problem. The “safety issue” was the potential for the tailgate to spontaneously open, but all kinds of tailgate misbehavior can occur from water contamination of that control card.    There is no real fix yet. The initial recall just disabled the tailgate. Later, when parts became available, they would replace bad parts with new parts of the same bad design. My dealer is going nuts because the few times I let them get their hands on my truck, my tailgate is off due to a slide-in camper installation. They really want to cut my tailgate wires, but I won’t give them the chance. I will let them get their dirty hands on it when a real fix (redesign) is available.  My tailgate, which works just fine with sealant plugging the drain holes, will remain safe in a dry storage crate until then.  

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...