Jump to content

Recommended Posts

Posted

I haven't seen anyone with official numbers. displaying the height of our trucks so I decided to pull it in the garage and measure up a couple of points.

 

Keep in mind, this is a 2019 Trail Boss Custom, Z71, Crew Cab, Standard Bed, with ~3000miles. Everything is completely stock and the tank was 95% full.

 

I measured the following heights;

- all 4 corners(at the fender) measured at the center of the wheel

- front diff (lowest point)

- rear diff (lowest point)

- front shroud/bumper (lowest point)

 

I've taken the measurements twice, once SETTLED and once UNSETTLED. To better define the terms, the settled measurements were taken by simply driving the truck in the garage, and measuring. I weigh around 200lbs ( seems to matter as there was a little lean tot he driver side).

 

The unsettled measurements were taken by, lifting the vehicle, front and back, just to the point where the tires were off, then slowly letting the jack down and removing it.

 

SETTLED Measurements;

DS front - 39 1/4"

DS rear - 41 3/8"

PS front - 39 1/2"

PS rear - 41 3/8"

front diff - 13"

rear diff -  9"

bumper - 13 5/16"

 

UNSETTLED Measurements;

DS front - 39 7/8"

DS rear - 41 1/2"

PS front - 40 1/8"

PS rear - 41 3/8"

front diff - 13 3/8"

rear diff - 9"

bumper - 14"

 

I've added all the pictures to this gallery ----> 

 

 

I've attached a couple of critical photos I think everyone should be aware of.

 

 

IMG_5925.JPG

IMG_5926.JPG

IMG_5927.JPG

  • Thanks 1
Posted
2 hours ago, tanner709 said:

I haven't seen anyone with official numbers. displaying the height of our trucks so I decided to pull it in the garage and measure up a couple of points.

 

Keep in mind, this is a 2019 Trail Boss Custom, Z71, Crew Cab, Standard Bed, with ~3000miles. Everything is completely stock and the tank was 95% full.

 

I measured the following heights;

- all 4 corners(at the fender) measured at the center of the wheel

- front diff (lowest point)

- rear diff (lowest point)

- front shroud/bumper (lowest point)

 

I've taken the measurements twice, once SETTLED and once UNSETTLED. To better define the terms, the settled measurements were taken by simply driving the truck in the garage, and measuring. I weigh around 200lbs ( seems to matter as there was a little lean tot he driver side).

 

The unsettled measurements were taken by, lifting the vehicle, front and back, just to the point where the tires were off, then slowly letting the jack down and removing it.

 

SETTLED Measurements;

DS front - 39 1/4"

DS rear - 41 3/8"

PS front - 39 1/2"

PS rear - 41 3/8"

front diff - 13"

rear diff -  9"

bumper - 13 5/16"

 

UNSETTLED Measurements;

DS front - 39 7/8"

DS rear - 41 1/2"

PS front - 40 1/8"

PS rear - 41 3/8"

front diff - 13 3/8"

rear diff - 9"

bumper - 14"

 

I've added all the pictures to this gallery ----> 

 

 

I've attached a couple of critical photos I think everyone should be aware of.

 

 

IMG_5925.JPG

IMG_5926.JPG

IMG_5927.JPG

SO does it clear a 7 Ft. garage door / Parking Ramp ??

Posted
16 minutes ago, slj2008 said:

SO does it clear a 7 Ft. garage door / Parking Ramp ??

 Not sure if you’re serious but I believe the cab height is 6’6”.

 

It’s fits in my 10’ garage door ?‍♂️

  • 2 years later...
Posted

I know this is an old, but I just picked up a 19 a week ago. I measured my fender heights at 41.25" all the way around. I am assuming it's stock in the rear and a level in the front?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
×
×
  • Create New...