Jump to content

Recommended Posts

Posted

My truck has some vibration but not as bad as the 2014 w/ 3.08 and 18"s I had first. Still not happy w/ ANY shaking on a new vehicle. Describe it best this way- when look to the right in my empty truck the passenger side sheet is vibrating like it the seat is equipped w/ a massage function. On my first truck equipped w/ 18s I could fell it in the passenger side seat and also the wheel a bit, on this new one w/ 20s and all terrain suspension I only see it as evidence.

 

That being said- my buddy just bought a full loaded SLT sierra and had real bad shakes and a humming sound, turned out he needs a whole new rear end.

 

I'm having my truck looked at as soon as I need my first oil change. Looks like GM will be eating some money on my repairs in the near future. I don't care if my shake is minor or not- if the rear end is indeed defective from the factory (something about pinion gears not matching up, chewing u where the drive shaft meets the rear) then I want it all new period.

  • Like 1
Posted

Problem solved i got another truck. identical with the exception this one doesn't have the vibration. Thanks to

the local dealer.

  • Like 5
Posted

My truck has some vibration but not as bad as the 2014 w/ 3.08 and 18"s I had first.

So you got rid of a truck that had a vibration to get another one with a vibration? Not trying to be a smart ass but I almost did the same thing. I was looking at trading to Sierra with the standard box, I was going to lose $5000.00 on the trade and then my buddy said "your going to look like an idiot if this new truck has a Vibration too." When I bought my truck I didn't notice the vibration right away so I could see it happening. Same buddy told me not to buy a first year truck either and i wish i would have listened to him. I will be trading it off but it will be on another make.

 

This is my 4th new chevy since 1999 and I've never even been close to being this disappointed in any of them. It's not just the vibration, the tranny shift like junk when driving in town, I could go on and on.

Posted

Got the truck back today. It ended up being a tire issue after all. Apparently the tire shop didn't check for tire roundness like they were supposed to do. I had one tire that was way out of spec. They said that the road force maximum allowed value on trucks is usually around 26 lb and that tire was over 32 lb and couldn't be brought into spec. So they ended up replacing it but they went through two tires since the first one they put on had an even higher number - 64 lb this time. The second tire came in at 19 lb. There is still a small amount of vibration but at 80 mph it is still less than it used to be at 75 mph and only starting to be "noticeable." I won't know more until I am able to get out on the highway for a longer trip. I may end up replacing all of the tires with a different brand but for now the ride is much better.

 

What made me turn away from a tire issue is that I had the tires rotated with no change in the vibration and the last time they balanced the tire, they were supposed to check for tire roundness as well. They said what was happening was a torsional vibration. The tire was feeding off the opposite tire on the front of the truck causing the variation in the vibration that I was feeling. Basically as I turned the tires would go in and out of phase with each other, creating the oscillation in the amount of vibration that I was feeling. When in phase, they would add together, amplifying the vibration and when out of phase, they would cancel each other out - almost since it never when away. This is a new one on me as I have never had this issue on any vehicle (this is my 7th vehicle).

 

The service manager came out and talked with me a bit on this issue. He said that the re-time of the drive shaft that they performed on my truck usually fixes the issue on about a third of the trucks. The other fixes have been new drive shafts to new axles if the issue is not a tire or wheel issue. My suggestion to everyone is to make sure your tires are not too far out of round first, even if this requires going to multiple tire shops just for the sake of a second opinion. Hopefully this helps some of you.

  • Like 3
Posted

I have a 2014 crew cab 5.3 and I too have a vibration problem. It seems to come and go. I hear a wobble sound between 35 and 40 mph and I feel vibration in the wheel at 50 and it makes my hand numb. Sitting at the dealership waiting for a fix.

Posted

Got the truck back today. It ended up being a tire issue after all. Apparently the tire shop didn't check for tire roundness like they were supposed to do. I had one tire that was way out of spec. They said that the road force maximum allowed value on trucks is usually around 26 lb and that tire was over 32 lb and couldn't be brought into spec. So they ended up replacing it but they went through two tires since the first one they put on had an even higher number - 64 lb this time. The second tire came in at 19 lb. There is still a small amount of vibration but at 80 mph it is still less than it used to be at 75 mph and only starting to be "noticeable." I won't know more until I am able to get out on the highway for a longer trip. I may end up replacing all of the tires with a different brand but for now the ride is much better.

 

What made me turn away from a tire issue is that I had the tires rotated with no change in the vibration and the last time they balanced the tire, they were supposed to check for tire roundness as well. They said what was happening was a torsional vibration. The tire was feeding off the opposite tire on the front of the truck causing the variation in the vibration that I was feeling. Basically as I turned the tires would go in and out of phase with each other, creating the oscillation in the amount of vibration that I was feeling. When in phase, they would add together, amplifying the vibration and when out of phase, they would cancel each other out - almost since it never when away. This is a new one on me as I have never had this issue on any vehicle (this is my 7th vehicle).

 

The service manager came out and talked with me a bit on this issue. He said that the re-time of the drive shaft that they performed on my truck usually fixes the issue on about a third of the trucks. The other fixes have been new drive shafts to new axles if the issue is not a tire or wheel issue. My suggestion to everyone is to make sure your tires are not too far out of round first, even if this requires going to multiple tire shops just for the sake of a second opinion. Hopefully this helps some of you.

 

Good news and some redemption for my many postings on check the tires like my post #91. All vibration would go away on yours if you could find a shop that knows how to true a tire and balance on the truck. Short of that, road force where they rotate the tire on the wheel if necessary is your next best bet. Having drive shaft balanced is the second step if still mild vibration.

 

Replacing OEM is highly recommended but trueing and on truck balance is still recommended on the non-oem.

I find Michelin LTX, M/S-2 or A/T-2 to be good. I find the M/S-2 to be just as good or better then the A/T in mild off road and mud.

 

I test drove a '14 cc, z-71 4wd and it had what I though was flat spotting as the tires ride was as bad as I have seen. We drove about 20 miles in very warm weather and it did not clear up. If I was going to buy that truck, I would have had the dealer swap out oems for Michelin and if road smooth would then buy.

  • Like 1
Posted

So you got rid of a truck that had a vibration to get another one with a vibration? Not trying to be a smart ass but I almost did the same thing. I was looking at trading to Sierra with the standard box, I was going to lose $5000.00 on the trade and then my buddy said "your going to look like an idiot if this new truck has a Vibration too." When I bought my truck I didn't notice the vibration right away so I could see it happening. Same buddy told me not to buy a first year truck either and i wish i would have listened to him. I will be trading it off but it will be on another make.

 

This is my 4th new chevy since 1999 and I've never even been close to being this disappointed in any of them. It's not just the vibration, the tranny shift like junk when driving in town, I could go on and on.

I got rid of the truck because I realized I didn't like the mushy suspension, SUV tires, 18" rims, and terrible 3.08 rear when compared to the All TErrain model I now have. The vibration was something I just chalked up to bad tires, but it could be something else who knows. The new one I have doesn't have any vibration you can feel, the truck tracks straight, its just slight vibration that I can see by monitoring the empty seat next to me.

 

Which new truck are you gonna get? The 2nd year Dodge or a Ford that will be antiquated next year when they introduce their "first year 2015" - either you're ending up in a new design bud.

Posted

My 2014 2500 has a vibration / growl at 1900-2100 rpm. Along with all the other small and big crap thats wrong with this pile. Ill take the vibration any day.

Posted

I have a 2014 Silverado double cab. It had a slight vibration around 70 mph when new, now it has 2800 miles on it and the vibration is gone. Rides and drives perfect.

 

One other comment, I recently had the chance to drive a friends new 2013 Ram Big Horn. There is no comparison when it comes to ride and drive...IMO The new Silverado rides and drives so much better. Truth be known, my friends Ram reminded me of my old 2006 GMC truck. Vibrations in the cabin and cowl shake, along with sloppy brakes, vague steering and body roll around corners. I assume Ram will catch up in the next 8 to 10 years, if Fiat doesn't kill the brand off before then.

Posted

Anybody noticed if the cylinder deactivation (aka active fuel management) is kicking in while they experience the vibration? I believe you can see the status on the driver info screen in the middle of the dash. I could see a truck lugging and vibrating if 4 cyl is not enough power to keep up the current speed. I test drive a chevy z71 yesterday and when accelerating I noticed a big slip when flooring the gas pedal, engine RPMs shot up 5,000 when shifting. I was planning on ordering a 6.2 with 3.73 gears but after reading some of the posts, vibration and tranny issues I may hold off.

Posted

I picked up the truck today and the service advisor said they can't really tell where the vibration is and that I should be happy mine drives better than some of the other ones. Not the right answer. They didn't even attempt a fix. Once I hit 50 mph the steering wheel vibrates and I don't like it. I have had 8 other chevy trucks in the past and this one as quiet as it is rides the worst. aside from the vibration it is just harsh every time you hit a bump. Maybe cheap shocks or just valved to stiff.

  • Like 1
Posted

 

 

I picked up the truck today and the service advisor said they can't really tell where the vibration is and that I should be happy mine drives better than some of the other ones. Not the right answer. They didn't even attempt a fix. Once I hit 50 mph the steering wheel vibrates and I don't like it. I have had 8 other chevy trucks in the past and this one as quiet as it is rides the worst. aside from the vibration it is just harsh every time you hit a bump. Maybe cheap shocks or just valved to stiff.
Mine vibrates in the steering wheel also @60+

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Latest Articles

  • Posts

    • consider doing electrical testing?  I would guess some power or ground wire/connection has a problem.   alldata.com has wiring diagrams, connector pinouts and diagnostic procedures you can use to find where the problem is.
    • can you tell if the reader is actually trying to get codes, and the pcm is reporting none, or is your reader just silently failing because it's not communicating with the pcm?
    • Any joy with this truck seems to be short-lived.   The CEL for P0172 ("bank 1" too rich) is now "intermittent".   I'm not sure where to check, or re-check, and my energy to keep chasing problems with junk is wearing thin. The P0172 seems to set as I'm coming to a stop, completely off the throttle, when fully warm. At least, that's what it's done the 3? times it's set.   Everything appears normal on the scanner EXCEPT long term fuel trim. There's only one bank on this vehicle because it's an OBD 1.5 with only one upstream O2 sensor. At idle, it's around -16.4% and will dip to -18% occasionally at idle or off-throttle. LTFT approaches 0 when throttle is held at 2500rpm. Short term appears normal, much closer to zero all the time. The LTFT tells me the engine is running rich at idle but compensating at higher load. But, why?   The EVAP purge valve doesn't appear to be leaking/sucking fuel vapor continuously. Is it sticking just as I come to a stop and the engine is choking on fuel vapor and sets the P0172? But that doesn't explain the persistently negative LTFT. Disconnecting the purge valve doesn't seem to make any difference.   I suppose that leaves another dang issue with the fuel injector. A leaking fuel pressure regulator, a new leak in the spider, or a leaking fuel injector/poppet valve I didn't see, or a small crack in one of the spider legs.   The vacuum line leading to the fuel pressure regulator doesn't have raw fuel in it. It doesn't even smell like fuel when it's pulled off, not until you suck air through it, then you can tell it leads to a fuel component. I'd consider that normal? Nothing is signaling this is a FPR issue from the outside, at least.   The oil smells like fuel but it's not building volume. I've noticed most oil in most engines smells like fuel to some degree so it's hard to say if the smell is an issue or not. Or if the engine just still smells like fuel because the crankcase was full of it a few hundred miles ago. But it's been changed twice since that original issue of the leaking fuel line dumping fuel into the intake.   Patience is running very thin. Every win seems to be accompanied by two steps backwards, or another issue that leads to removing at least the top half of the intake manifold. Enough! LOL
    • First off you mentioned "Toyo Says" and then gave the pressures 45/50, was this some person at the tire shop that pulled those numbers out of his head ?   Now of course I can't know your exact axle weights front and rear, however I have much the same pickup as yourself other than not knowing your starting weight as per the pounds the truck rolled out of the factory at due to the options yours did or didn't come with or what you have added beyond the extra tire weight. The correct way to know 100% where a person is at is by weighing each axle with the typical weight the vehicle is driven with and that means taking into account passengers and making sure you figure in a full tank of fuel and a little grace for whatever you may put in the bed "groceries" !    I am looking at and not that it really matters as all the tire companies use the same charts anyway, but I am looking at the comprehensive Toyo tire chart in the section that your tire falls under and I know it sounds confusing but your tire is not an LT metric tire like your factory tire but instead because its a standard inch measured tire its under a different category called an LT floatation series tire. That makes a difference as LT metric tires they don't want to see run below 35 psi at highway speed where as with the LT floatation series it can be run down to 25 psi on the highway as long as the weight on the said size of tire is agreeable with or less than that minimum 25 psi. It blows many people away that how is this physically possible, an empty truck for one thing and larger tires with the same size wheel diameter have a lot more air volume so they can carry the same weight as the smaller tire with less air pressure.    So my truck, I have the stock 275/65R20 wheels and tires and I have a bit of weight in the box with a bak flip cover and a rubber bed mat and some tools and spare gas. The front of my gas truck weighs a bit more than some trucks of the similar spec due to double batteries and alternators. However with full fuel and just me in the truck I am weighted such that I can run 40 front and 35 rear and so that is what I have done since day one.    If I base your truck at or slightly below the weight of my truck, in theory with your tires going by the tire chart you might be right around a minimum of 30 pounds front and 25 pounds rear. Of course that would hit pretty much minimum cold inflation pressure one could run with that tire size and a near empty truck. If you have access to an accurate weigh scale to do individual front and rear axle weights I would suggest you do that and make sure your topped up with fuel and whatever else in the truck before you weigh it and then you will have a great starting point to work off of and figure out what your bare minimum pressures are you can safely run. If you do much in the way of hot weather high speed driving, bumping up a bit for a safety margin is never a bad idea but just depends on what type of driving you do. I will include the Toyo chart and the floatation series sizes start on page 31. Without a doubt at these pressures I am speculating at minimum wise for your truck, it would most certainly ride very different then it did when you were using 55 lb front and rear.     https://www.toyotires.com/media/pxcjubjs/application_of_load_inflation_tables_20200723.pdf
    • Take an automotive stethoscope to the vacuum pump. Iirc those tick as well. 
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...