Jump to content

Recommended Posts

Posted

 

This is exactly what I am experiencing. I dont have any vibrations up until about 72mph and then if I had a cup of coffee more than 3/4 of the way full in the console it would have shaken it out on the floor.

 

Exact same thing. That's good that it's not just me then LOL.

 

I go to the dealer for the first time today at 12:30pm and will see what they say.

Posted (edited)

Need to copy and paste this entire thread into an email and send it to all of the top level GM executives. Getting their email addresses may be a bit tricky though.

Edited by 14LTZZ71
Posted

So I just got back from my dealer visit.

 

Apparently GM is well aware of the issue. The service manager I worked with was a really cool guy and he said they have had a issues with multiple trucks and have had the engineers out more than once to try and diagnose what the issue is with no luck. He said GM has know about the issue for about 6 months and just recently told the dealer to stop throwing parts at the truck. He said they have tried replacing tires, rims, rear and, and driveshafts on multiple trucks with it never fixing the issue, so essentially they are awaiting GM to figure out whats going on.

 

As far as my ruck goes, we got it up to 75 twice in a ride along and couldn't replicate the issue. It drove me nuts and made me look liek a idiot, but he said he could try RF balancing the tires if I wanted. I declined for the time being as I wanted to see why it wasn't vibrating now and to see if it still was. On my way home on the highway, sure enough, it started vibrating again at 72mphish. The only difference was the roads we were driving on, one was a "smooth" highway, which made it vibrate, and the other was a "smoothish" back road. I took another way home as opposed to the normal highway route and got up to 75 mph, and no bad vibrations at all...... Does not make any sense besides the highway I am driving on is messed up, but that would have to mean its messed up for a 20 mile stretch on both sides.

 

I wonder if on the "back roads" if the suspension is hitting smaller bumps that is "loosening" up the suspension making it not so stiff? I do not know....

 

The service manager said my Sierra was one of the smoothest he has driven. He could have been blowing smoke, Im not sure. We drove a "loaner" Sierra that vibrated WAY worse than mine.

Posted (edited)

So I finally got around to bringing mine in to get it's first oil change at 5000km. I told them about the vibration and this is the 3rd dealer who either played dumb or literally have never heard of the issue yet.

Anyways since I have aftermarket 18" rims with Grabber AT2 rubber, they said there wasn't much they could do unless I put the stock rims/tires back on. They said they checked the u-joint, etc...etc... but there would be nothing they could unless they get my stock tires back on. Only problem, I sold the tires 3 months ago. SO with that being said, sounds like they are basically pushing me off to the side because they are blaming my road force balanced tires and rims. The truck shook WITH the stock rims and tires before the swap out as well.

This is also the dealership that took literally 2.5 hours to do an oil change when I had an appointment. Soooooo.... I'm getting tired of GM already.



Edited by RageMonkey
Posted

So I just got back from my dealer visit.

 

Apparently GM is well aware of the issue. The service manager I worked with was a really cool guy and he said they have had a issues with multiple trucks and have had the engineers out more than once to try and diagnose what the issue is with no luck. He said GM has know about the issue for about 6 months and just recently told the dealer to stop throwing parts at the truck. He said they have tried replacing tires, rims, rear and, and driveshafts on multiple trucks with it never fixing the issue, so essentially they are awaiting GM to figure out whats going on.

 

As far as my ruck goes, we got it up to 75 twice in a ride along and couldn't replicate the issue. It drove me nuts and made me look liek a idiot, but he said he could try RF balancing the tires if I wanted. I declined for the time being as I wanted to see why it wasn't vibrating now and to see if it still was. On my way home on the highway, sure enough, it started vibrating again at 72mphish. The only difference was the roads we were driving on, one was a "smooth" highway, which made it vibrate, and the other was a "smoothish" back road. I took another way home as opposed to the normal highway route and got up to 75 mph, and no bad vibrations at all...... Does not make any sense besides the highway I am driving on is messed up, but that would have to mean its messed up for a 20 mile stretch on both sides.

 

I wonder if on the "back roads" if the suspension is hitting smaller bumps that is "loosening" up the suspension making it not so stiff? I do not know....

 

The service manager said my Sierra was one of the smoothest he has driven. He could have been blowing smoke, Im not sure. We drove a "loaner" Sierra that vibrated WAY worse than mine.

This is not sounding promising to me. And yes, I was mistaken on the MPH for me. I think I said 75, its more like 73. :(

Posted

My ¢.02 Rubber compounds are hiding, and amplifying the flutter if there is one in these trucks. I believe 100% this is a harmonics thing. Here's my reasoning, 2014 crew cab 4x4 6.2. Dealer swapped 2 Goodyear ls2's after road force numbers were out of spec. No change. Replaced all 4 with Michelin ltx, 20". Rode perfect, after about 5k miles I felt an intermittent "flutter" again at 73+ hit or miss on certain stretches of road. My wife's car, ex wife's car, and best friends car all have same flutter on the same road.

Posted

My loaner that I am driving while my truck is at the dealer is a vibrator.

 

Its an SLE Crew cab, short box, 5.3, 3.08 gears. It has either the basica 17" or 18" wheels and i dont remember what tires. has a subtle vibration around 45-50mph, something that my truck does NOT do. Haven't had an opportunity to take the loaner on the highway tho.

 

I can see why this would annoy people.

Posted

I have read about a third of these pages and seems like there is a never ending issue. I have a 2014 silverado 1500 crew cab 5.3l 2wd and is lifted 7" on 35s. I thought it had to be something with the lift but it has been lifted since 1000 miles and drove perfect. Now i have 9000 miles and the shake at 55 is rediculous. I called the dealer to see if they had any issues with other trucks with the vibration and he told me he had a few but were solved when roadforced the tires. I dont even want to take it in becuase they are going to blame it on the lift.... I guess i have to deal with it untill gm comes up with a fix!

 

The tires i have are Toyo Alterains and rouch country lift kit which included new shocks. So in my opinion its not the tires nor the shocks in my case.

Local Shop i took it to that does lift kits and so forth thought it was the drive line angle so they changed it for me and now it seems worse.

IDK what to do!

Posted

I have read about a third of these pages and seems like there is a never ending issue. I have a 2014 silverado 1500 crew cab 5.3l 2wd and is lifted 7" on 35s. I thought it had to be something with the lift but it has been lifted since 1000 miles and drove perfect. Now i have 9000 miles and the shake at 55 is rediculous. I called the dealer to see if they had any issues with other trucks with the vibration and he told me he had a few but were solved when roadforced the tires. I dont even want to take it in becuase they are going to blame it on the lift.... I guess i have to deal with it untill gm comes up with a fix!

 

The tires i have are Toyo Alterains and rouch country lift kit which included new shocks. So in my opinion its not the tires nor the shocks in my case.

Local Shop i took it to that does lift kits and so forth thought it was the drive line angle so they changed it for me and now it seems worse.

IDK what to do!

 

In your case, I would almost definitely attribute your issues to the lift. Did you have the lift kit re-torqued after 500-1000 miles after install? and also I think every 5000 miles after that you should check the lift kit bolts.

Posted

I had the shop look over the lift. (not sure if they re-tightend everything) and told me everyting looks fine. no split bushing or anything. I also have the slight vibration at idle. I tried the water cup trick and sure enough its shaking. I guess i am going to be one of those few who wait untill they come out with something to fix it to get it done. Only because there is way more things that could be the problem on my truck.

Posted (edited)

Large oversized tires with a pretty aggressive tread pattern could also be a contributing factor. They are hard to keep balanced and also hard to maintain even tread wear.

Edited by 97SierraSLT
Posted

Picked up my 14 Sierra 40 to 50 mph vibrator after a 9 day dealer visit while I was on a near 2000 mile motorhome trip (94 Ford SuperDuty chassis). Glad my GMC doesn't shake like that Ford! Waiting for a new rear end GM thinks will correct my vibration. My feeling is that this is a transmission issue but what are the chances that GM would start replacing all of our transmissions? ZERO.

Posted

Large oversized tires with a pretty aggressive tread pattern could also be a contributing factor. They are hard to keep balanced and also hard to maintain even tread wear.

 

I agree but my tires are more alterain and not mud terian tires so they are not agressive at all. I had them roadforced balanced and roated with same issue. Trade wear is even since they are fairly new anyways

Posted

My feeling is that this is a transmission issue but what are the chances that GM would start replacing all of our transmissions? ZERO.

 

Exactly why I think they'll address the issue for 2015's and leave 2014 owners out to dry....

Posted (edited)

I could see where the differential could be contributing factor for this vibration issue. Not taking into account harmonics, to induce vibration a component/assembly must be out of balance and the rotating mass of the components/assembly must be taken into account. I do not believe the ring gear is a major contributing factor as it is a precision machined component but has a good deal of rotating mass. Couple this to the differential carrier and there could be an issue and the carrier is made from a raw casting and not every surface is precision machined and the carrier has a lot of rotating mass.

 

Assuming your tach is at 2000 RPM at 70 mph and you have 3.08 gears, your differential is spinning at 433 RPM ((2000 RPM x .667 final transmission drive ratio / 3.08))

 

I wonder if all of these various rotating components/assemblies are dynamically balanced? They should be, but who knows as it does add labor & cost.

 

I'd agree that the vibration is a combination of several contributing factors and would also lean towards the transmission being the largest influence. But, the cost to replace would be prohibitive and GM would rather just do a buyback and get the customer into a different 2014 or 2015 model.

Edited by 97SierraSLT

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Latest Articles

  • Posts

    • Glad it worked for you. I tried that 1st, about 2 years ago. Didn't help. I also tried doing a hard reset (disconnecting battery for minimum of 30 minutes). Worked a couple times, but after one summer of doing it over and over, that no longer worked.  I was fairly confident it was either the compressor or a failed actuator, but I just couldn't identify which one. Had to research which actuators do what and which last numbers are associated with each.
    • Took me FIFTEEN MINUTES to find this. Isn't that a problem? On the mainstream media I can INSTANTLY find 100 articles bashing President Trump ... but when it comes to TRUTH in American corporate news & search engines, it's carefully filtered to support ONE SIDE. A Republic cannot survive like this! Incredible! Even all the AI searchers out there failed as well! ChatGPT said it needed more details on the video that I provided a DIRECT LINK to! I thought AI was the be-all, end-all?? I had to dig it up myself. This should be FRONT PAGE NEWS!!! 🤬   Here's the statement directly from our President:     Glenn Beck's reporting on the operation:   https://glennbeck.com/watch/videos/trump-just-revealed-a-massive-military-secret-that-lowered-gas-prices   In case that link doesn't work, here's the YouTube link:    
    • More is cylinder deactivation. Kia-Hyundai Ive had 4. The warranty is the same 10 years 100K miles. My grandson drives the first one 05 Elantra GT. My wife drives the second one 2011 Genesis. The Genesis still performs as new and looks great. The Elantra looks rough. He’s not kind to it. The third was a Genesis coup. The fourth was a Santa Fe. Those were my daily drivers. I don’t keep them long. Kia is the same as Hyundai with the same warranty. I looked at the K-4 today. Too small, otherwise pretty good buy. Most of Hyundai and Kia’s have a performance upgrade. 
    • Thanks for the point of reference 
    • Great question. Answer....depends. One the volume of the crankcase, the driver that will actually be using the vehicle and the amount it uses plus the distance expected for that next trip. Couple of for instances:   Wife is going to drive Dizzy to Moline and back plus a bit around town so say 500 miles on the day. I know from years with that SUV that around town and local rural it uses about a quart in 1250 miles. But on the Interstate and her at the wheel without her anchor nagging her she'll push it and it will drop a quart in about 800 miles. Hence, around town I wait to somewhere between a quarter down to a quart down. On her trip I'd top it if it was down a few ounces and hope for the best.    Have I overfilled one? You mean by adding before it needs a full quart I assume. No, not once after finding the true fill mark.  I know the dipsticks of everything I drive and add what it needs. I learn this by doing the first oil change a quart low. Run the motor for a few minutes. Let it sit over night. Check and mark. Then add half a cup at a time making note of the place on the stick. I add through the dipstick tube with a barbeque basting bottle. Give it a few minutes to drain down and check again.    A vehicle like Dizzy that uses this much oil will take a few quarts between 3K changes. I keep one in the vehicle with the bottle and a bag. (Mindful of it's fullness) Not a big deal and never makes a mess of it. There is no such thing as "multiple quarts' in my shop for any specific oil. There will be a maximum however of the number of different oils used over the fleet.     Dizzy holds a nominal 5 quarts. So the first fill was indeed over as it actually took 4.75. My vehicles are fit with Valvomax valves so I can meter an ounce on the drain if need be. Found her mark first crack at it. Never to be repeated.    Pepper uses none between changes so I don't keep a quart in that one. Straight up 6 quarts put her dead on the full line. Check it ever fuel stop. They will surprise you when they start using.    Raven holds 3 liters or 5.44 ounces over three quarts. I add 3 quarts and 6 ounces. That gives me 5 oil changes on my orphan quart.    Lawnmower holds about 3/5 of a quart. I don't over fill it to prevent an orphan. So yea, depends. 
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...