Jump to content

Overheating while towing

Cascade Venturer
 Share

Recommended Posts

Cascade Venturer Enthusiast

Cascade Venturer

Posted
Posted

06 Silverado 2500hd 6.0

 

My Silverado is getting really hot while towing up hill, to the point that the "Engine Coolant Hot" light is coming on. (Which I stop and let it cool down). This has gradually gotten worse. Truck does not get hot while towing on flat terrain. Any ideas?

davester Senior Enthusiast

davester

Posted
Posted

could be a problem with the thermostat, or radiator fins aren't clean, or you've put some bling up front that reduces airflow through the rad, or some of the ducting up front is missing (that directs air to the radiators), or water pump isn't pushing enough water (problem with the impeller in the pump)

  • Like 1
Formulabruce Enthusiast

Formulabruce

Posted
Posted

Flush the cooling system. Remove the T stat housing and really flush it out. If you tow a lot, you can use a 160 T-stat, which works well, and engine still runs in closed loop.

I would also upgrade the stock transmission cooler to one twice the size ( easy with grill off)

Mikebtte Enthusiast

Mikebtte

Posted
Posted

As talked about above, make sure the radiator is clean. If you are towing in areas with high altitude, you need all the air you can get. Confirm the thermostat is fully opening, and check water pump pressure and radiator cap. If the cap is failing you will not maintain a properly cooling system. 

 

Cascade Venturer Enthusiast

Cascade Venturer

Posted
  • Author
Posted

Thanks for the responses. No bling added to my truck, its as stock as can be. It doesn't have and issue with temperature unless towing uphill. I took my grill off about a month ago and cleaned off the radiator and condenser with compressed air... didn't make a difference though. I'm having to pull over sooner and sooner to let it cool off. I've reached in and tried spinning the fan and it seems really tight and barely spins. I will test some of the above mentioned and see if that helps.

txab Senior Enthusiast

txab

Posted
Posted

You need to check the fan clutch while hot. You tube has several videos. Basically at idle, take a rolled up newspaper and slowly advance it into the fan. It should resist stopping. I've seen clutches seem to perform correctly until this test

Cascade Venturer Enthusiast

Cascade Venturer

Posted
  • Author
Posted
1 hour ago, txab said:

You need to check the fan clutch while hot. You tube has several videos. Basically at idle, take a rolled up newspaper and slowly advance it into the fan. It should resist stopping. I've seen clutches seem to perform correctly until this test

Ok. I will test it out tomorrow. Thanks

Cascade Venturer Enthusiast

Cascade Venturer

Posted
  • Author
Posted
On ‎11‎/‎18‎/‎2019 at 7:14 PM, txab said:

You need to check the fan clutch while hot. You tube has several videos. Basically at idle, take a rolled up newspaper and slowly advance it into the fan. It should resist stopping. I've seen clutches seem to perform correctly until this test

I took the truck for a drive and let it heat up to operating temperature. I did the test and had no change in fan speed. The newspaper didn't effect it.

  • 7 months later...
Cascade Venturer Enthusiast

Cascade Venturer

Posted
  • Author
Posted

In the process of replacing radiator, fan clutch, water pump etc. Here is the fan-side of the radiator. Quite a bit of smashed fins. Do you think that is enough to cause my overheating issue? The pics don't really do it justice either.  I'm replacing it anyways, just wanted some reassurance that I'm heading down the right path.

rad 2.jpg

swathdiver Senior Enthusiast

swathdiver

Posted
Posted
45 minutes ago, Cascade Venturer said:

In the process of replacing radiator, fan clutch, water pump etc. Here is the fan-side of the radiator. Quite a bit of smashed fins. Do you think that is enough to cause my overheating issue? The pics don't really do it justice either.  I'm replacing it anyways, just wanted some reassurance that I'm heading down the right path.

rad 2.jpg

Sure can.  Probably wore out inside too.  Same with condenser.

  • Like 1
jzaldivar Enthusiast

jzaldivar

Posted
Posted

Mine has the same issue. Plugged radiator...use of wrong coolant will cause it to gel up inside, thus clogging it up.


Sent from my iPhone using Tapatalk

  • Like 1
  • 1 year later...
hiking_mike Enthusiast

hiking_mike

Posted
Posted

I took the stack apart last spring> I noticed the air "holes" in the intercooler are larger the the radiator. This causes debris to pass through the intercooler and get caught in front of the radiator.

After cleaning radiator of gunk and dead bugs, I noticed the transmission a lot cooler when towing a 7,000 pound trailer all the way to Key West in early July.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • Chuck FB
      Joke Thread

      By Chuck FB · Posted

      Fred was in the fertilized egg business. He had several hundred young pullets, and ten roosters to fertilize the eggs He kept records, and any rooster not performing went into the soup pot and was replaced. This took a lot of time, so he bought some tiny bells and attached them to his roosters. Each bell had a different tone, so he could tell from a distance, which rooster was performing. Now, he could sit on the porch and fill out an efficiency report by just listening to the bells. Fred's favourite rooster, old Butch, was a very fine specimen, but this morning he noticed old Butch's bell hadn't rung at all! When he went to investigate, he saw the other roosters were busy chasing pullets, bells-a-ringing, but the pullets, hearing the roosters coming, would run for cover. To Fred's amazement, old Butch had his bell in his beak, so it couldn't ring. He'd sneak up on a pullet, do his job and walk on to the next one. Fred was so proud of old Butch, he entered him in the City Show and he became an overnight sensation among the judges. The result was the judges not only awarded old Butch the "No Bell Piece Prize," but they also awarded him the "Pulletsurprise" as well. Clearly old Butch was a politician in the making. Who else but a politician could figure out how to win two of the most coveted awards on our planet by being the best at sneaking up on the unsuspecting populace and screwing them when they weren't paying attention. Vote carefully in the next election, you can't always hear the bells.
    • chfkief
      FS: Black Bear Performance AutoCal Tuning System

      By chfkief · Posted

      Do you still have?
    • 3CarSeatDad
      High Country Suburban build confirmation

      By 3CarSeatDad · Posted

      Can someone confirm if the GM order workbench terminal is able to validate a custom build sequence:   1) Initialize the Allocation Base: Open a new vehicle build queue, select the 2026 Chevrolet Suburban 4WD, and pick the High Country (3LZ Preferred Equipment Group).   2) Select the Diesel Powertrain: Go directly to the engine configuration screen and choose RPO code LZ0 (3.0L Duramax Turbo-Diesel). Ensure it maps to the MHS 10-speed automatic transmission.   3) Deploy the Seating Swap: Navigate to the Interior Options screen and enter RPO code ATT to replace the standard captain's chairs with the power-release 60/40 bench seat. Because you are not trying to force a separate luxury or air-suspension bundle, the standard, premium D07 Fixed Floor Console remains active. The system will accept this change immediately without triggering a warning message.   3)Apply Heavy-Duty Hauling Capability: Input RPO code NHT (Max Trailering Package). The commercial terminal will automatically bundle the required trailering hardware and software modules to support the diesel engine's maximum towing capacity.   5) Layer the Premium Tech and Glass: Separately add code C3U (Panoramic Power Sunroof) and code UKL (Super Cruise) to the order screen.   6) Run the Final Validation: Click the "Validate Order" button at the bottom of the interface.
    • revmanii
      Looking at ordering a '26 WT because I want a std cab, std bed

      By revmanii · Posted

      Spent the last hour or 2 googling and reading up on the spacer thing. I don't like the loss of thread contact on the slip on spacers, but it appears you can get "extended" lug nuts that reach into the hole of the wheel to get back the lost threads. Looks like the only true hubcentric slip on spacers are at least .375". I'd want as little as I could get away with and don't want to cause other clearance issues going any thicker. Bora seems to offer what appears to be a well made .375" spacer and extended lug nuts. I searched here and did find a couple threads recommending Bora. But not cheap. By the time I buy spacers and lugs, new TPMS sensors, then pay a tire shop to install the new sensors, I suspect I'm going to be in over $400. Thinking about running out and getting some washers to put behind the wheel to see if .375" is enough to clear calipers, turn lock to lock without rubbing, and to see if the wheels/tires look strange pushed out a little. This would just be to check fitment.
    • Core-Lokt
      Road Master Active Suspension

      By Core-Lokt · Posted

      Roadmaster makes some quality parts; I have their sway bar. I considered the RAS, but I ended up bagging. I didn't know what kind of ride I'd get with RAS, and the bags have interior jounce bumpers, so I can run 0 pounds pressure. I figured I'd have the best of normal suspension ride with assist on-demand. But it seems you got pretty much the same in one item.

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...