2014+ K2XX - Center Console Swap / Retrofit - Plug and Play Harness!

[Wade McLeod]

Phil, i am interested in purchasing your PnP harness, i already have my new console for my 2016 Silverado. How do i get in contact with you to place an order?

 

Thanks Wade 

[pgamboa]

Phil messaged me back and said that some have reported this while others have not. 
 
So, this is what I did:
I ran the blk/brown cable from blk HMI to brown usb inside the console. This feeds the usb hub inside the arm rest area. Checked and car play now works at the usb connection inside the arm rest area.
 
My next thought was to run the  green HMI to the input on the double usb connector of the front upper console part, and run the output to the usb in the glove box.  This meant I would need the grn/gray cable, but I had purchased the blk/gray cable. And also would need a black to regular USB connector. Not sure if they even make this or not.  
 
But I had some wire cutters!
 
i cut he blk/gray cable in half, and did the same to the grn to USB from the glove box. Swapped ends so that I ended up with the glove box USB with a black connector on the other end instead of a green. I then plugged the blk end into the output of the double USB hub in the front upper console and the other end into the glove box. I went ahead and ordered a new grn/gray cable, but just to test things out I spliced the left over ends to make a grn/gray cable. Plugged it in from the grn HMI to the input of the double USB hub in the upper front console  and now have car play at all three USB locations!
 
Go figure. 

Just to clarify...

You went green port of HMI to grey on the front hub? Then black port of HMI to brown for the inside hub?


Sent from my iPhone using Tapatalk

[b-garage]

1 hour ago, pgamboa said:

Just to clarify...

You went green port of HMI to grey on the front hub? Then black port of HMI to brown for the inside hub?


Sent from my iPhone using Tapatalk

That is correct sir. And then by cutting and splicing I made the black output of double usb hub go to the glove box.

[Hendrix711]

Phil i am putting a center console out of a 2014 gmc sierra into a 2017 gmc sierra can you tell me which cables I need. Thx Darryl

[Chase Gurganious]

Sold. How do I order.  I have already installed the 2016 console in my 2016 Silverado.  I just need to order the harness.

Edited April 13, 2018 by Chase Gurganious

[pgamboa]

Phil i am putting a center console out of a 2014 gmc sierra into a 2017 gmc sierra can you tell me which cables I need. Thx Darryl

Please see the first post of this thread for the USB cable requirements. I also need to know if you have the 16-Pin or 23-Pin Connector under the passenger seat.


Sent from my iPhone using Tapatalk

[BluEyeItln]

@pgamboa  Are the other cables needed already part of what was dismantled?  I was just going through the video and I don't think I have the brown to gray cable or possibly more.  HELP!  I don't want to be missing anything.

[pgamboa]

1 hour ago, BluEyeItln said:

@pgamboa  Are the other cables needed already part of what was dismantled?  I was just going through the video and I don't think I have the brown to gray cable or possibly more.  HELP!  I don't want to be missing anything.

You’ll need to get 2 new USB cables in order to get the USB Data side of the hubs working. 

[BluEyeItln]

Do you make those cables?   If not where can one get those?

[MartyMar0911]

Phil, I know you're busy and have many messages with requests and orders, but could i order a PnP for full console with the 16 pin connector? 

 

thanks again for all ya do.

 

-Eric

[Koppster]

Phil, when I send you my 23 pin will I have any USB capability while the cable is removed from the truck? 

 

Thanks,
Rick

[hackitz]

so want to do this, where is everyone buying the center console?

[Frank Jr]

On ‎4‎/‎20‎/‎2018 at 8:05 PM, hackitz said:

so want to do this, where is everyone buying the center console?

Some find in junk yards or ebay. Like me I bought it brand new from auto parts on line. Read some of the post here and you will see a lot of answers for your question.

Frank

 

[pgamboa]

On 4/13/2018 at 6:42 PM, BluEyeItln said:

Do you make those cables?   If not where can one get those?

I don't make the USB Cables, you'll have to source those from any place that has them in stock.  Part #s are provided in the first post pic.

On 4/15/2018 at 1:34 AM, MartyMar0911 said:

Phil, I know you're busy and have many messages with requests and orders, but could i order a PnP for full console with the 16 pin connector? 

 

thanks again for all ya do.

 

-Eric

Eric, yes - please PM for ordering instructions.  For some reason, I don't get notifications when someone replies to my threads.  

On 4/15/2018 at 4:32 AM, Koppster said:

Phil, when I send you my 23 pin will I have any USB capability while the cable is removed from the truck? 

 

Thanks,
Rick

No.  The 23-pin cable provides the necessary power to your jump seat and the USB it has in it.

[WesternMike]

Anyone need this? $110 shipped to you.