Jump to content

Bilstein 5100s are a HUGE upgrade!

CS25

By CS25
in Modifications, Wheels & Tires

 Share

Recommended Posts

bearded_warrior Enthusiast

bearded_warrior

Posted
Posted

Yeah it needs to be removed again to change. Cant adjust in place.  A bit of advice I read was to measure from the fender to the middle of the hub instead of the ground to account for uneven ground/tire differences. I'm sure others here have helpful advice too but it was more accurate than the ground measurement in my case.

  • Replies 388
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

Mike Borowski
Mike Borowski

Installed 1500’s in the rear today. Stock height. What. A. Difference!  I wasn’t sure what to expect but WOW!  It rides so much better now, I want to have the fronts done!  The back doesn’t hop around

lapoolboy
lapoolboy

Hard to tell if it's more shock or more tire since you installed them at the same time.

romclean1
romclean1

Install done, for sure an improvement.  Settles a bunch of the bunny hop tendencies and makes potholes more bearable.  Feels more planted on corners for sure.  The ultimate test for me is the highway

Posted Images

Dunn Senior Enthusiast

Dunn

Posted
Posted (edited)

am doing AT4 5100s with eibach springs on my Elevation....should be 3"-3.2" in front on lowest setting, will add rear 2" block.....install shortly also will do the arm/small drop on half shafts.....bit of rake is fine with me, 

Edited by Dunn
Dunn Senior Enthusiast

Dunn

Posted
Posted (edited)

dbl post

Edited by Dunn
ms6040 Enthusiast

ms6040

Posted
Posted (edited)

Got my front Bilstein 5100's installed on my 21' RST Z71 5.3L yesterday. I did the front and the rears both. I did the install for the rear's myself but didn't feel comfortable with doing the fronts.

 

First impressions - Quite noticeable difference/improvement in ride quality over the stock Rancho's. I understand the "more planted" feel that other guys are saying now, but I was confused about what that really meant, but the 5 mile trip home I caught on. I was torn between going with the 1.5" or 2" setting. I went with the 2" setting.

 

Measurements from level cement to top of wheel well before were as follows for stock: Front - Driver 38", Pass 37 7/8" Rear - Driver 39 1/8", Pass 39 1/4". Once swapping the rear shocks for the Bilsteins, the front measurements didn't change, but gained a 1/4" on the rear on each side exactly. I'm thinking that may settle out with time.

 

Measurements after adding the front struts to the 2" groove are as follows: Front - Driver 39 5/8", Pass 39 5/8" Rear - Driver 39 1/8" Pass - 39 1/8". I also had stock size (275/60/20) Ridge Grapplers installed to replace the stock tires. I wanted to go 285/60/20, but the cost increase/difference of over $400 from stock size, I decided not to for that small difference.

 

So on my setup, the 2" groove yielded 1 5/8"-1 3/4" on the front, which I am happy with because I was torn between the 1 1/2" and 2" setting, so in the middle is great. From the measurements, the front is now 1/2" higher than the rear and it does appear to be higher from an eye test. I will be adding a 1" block in the rear to hopefully get it back to at least level or a slight rake to the eye test. Just my initial thoughts. I will post photos over the weekend.

Edited by ms6040
  • Like 2
romclean1 Enthusiast

romclean1

Posted
Posted
25 minutes ago, ms6040 said:

Got my front Bilstein 5100's installed on my 21' RST Z71 5.3L yesterday. I did the front and the rears both. I did the install for the rear's myself but didn't feel comfortable with doing the fronts.

 

First impressions - Quite noticeable difference/improvement in ride quality over the stock Rancho's. I understand the "more planted" feel that other guys are saying now, but I was confused about what that really meant, but the 5 mile trip home I caught on. I was torn between going with the 1.5" or 2" setting. I went with the 2" setting.

Nice write up!  I'm sure it will benefit others looking to do the same 

  • Thanks 1
Msol Enthusiast

Msol

Posted
Posted

If I upgrade the front shocks to the Bilstein 5100s on my 2020 RST 2wd, will the preload spacer still fit on the shock and all other strut components from the lift? In other words is the body size of the Bilstein 5100 thicker than stock shocks on a 2wd?

Sent from my Pixel 2 XL using Tapatalk

LakeAnna72 Enthusiast

LakeAnna72

Posted
Posted
On 4/16/2021 at 9:20 AM, ms6040 said:

Got my front Bilstein 5100's installed on my 21' RST Z71 5.3L yesterday. I did the front and the rears both. I did the install for the rear's myself but didn't feel comfortable with doing the fronts.

 

First impressions - Quite noticeable difference/improvement in ride quality over the stock Rancho's. I understand the "more planted" feel that other guys are saying now, but I was confused about what that really meant, but the 5 mile trip home I caught on. I was torn between going with the 1.5" or 2" setting. I went with the 2" setting.

 

Measurements from level cement to top of wheel well before were as follows for stock: Front - Driver 38", Pass 37 7/8" Rear - Driver 39 1/8", Pass 39 1/4". Once swapping the rear shocks for the Bilsteins, the front measurements didn't change, but gained a 1/4" on the rear on each side exactly. I'm thinking that may settle out with time.

 

Measurements after adding the front struts to the 2" groove are as follows: Front - Driver 39 5/8", Pass 39 5/8" Rear - Driver 39 1/8" Pass - 39 1/8". I also had stock size (275/60/20) Ridge Grapplers installed to replace the stock tires. I wanted to go 285/60/20, but the cost increase/difference of over $400 from stock size, I decided not to for that small difference.

 

So on my setup, the 2" groove yielded 1 5/8"-1 3/4" on the front, which I am happy with because I was torn between the 1 1/2" and 2" setting, so in the middle is great. From the measurements, the front is now 1/2" higher than the rear and it does appear to be higher from an eye test. I will be adding a 1" block in the rear to hopefully get it back to at least level or a slight rake to the eye test. Just my initial thoughts. I will post photos over the weekend.

Thanks for sharing! I have an appointment this Thursday to have mine done and will probably  go with the 1.5 

Thanks!

IMG_4141.jpg

ms6040 Enthusiast

ms6040

Posted
Posted
On 4/16/2021 at 9:20 AM, ms6040 said:

Got my front Bilstein 5100's installed on my 21' RST Z71 5.3L yesterday. I did the front and the rears both. I did the install for the rear's myself but didn't feel comfortable with doing the fronts.

 

First impressions - Quite noticeable difference/improvement in ride quality over the stock Rancho's. I understand the "more planted" feel that other guys are saying now, but I was confused about what that really meant, but the 5 mile trip home I caught on. I was torn between going with the 1.5" or 2" setting. I went with the 2" setting.

 

Measurements from level cement to top of wheel well before were as follows for stock: Front - Driver 38", Pass 37 7/8" Rear - Driver 39 1/8", Pass 39 1/4". Once swapping the rear shocks for the Bilsteins, the front measurements didn't change, but gained a 1/4" on the rear on each side exactly. I'm thinking that may settle out with time.

 

Measurements after adding the front struts to the 2" groove are as follows: Front - Driver 39 5/8", Pass 39 5/8" Rear - Driver 39 1/8" Pass - 39 1/8". I also had stock size (275/60/20) Ridge Grapplers installed to replace the stock tires. I wanted to go 285/60/20, but the cost increase/difference of over $400 from stock size, I decided not to for that small difference.

 

So on my setup, the 2" groove yielded 1 5/8"-1 3/4" on the front, which I am happy with because I was torn between the 1 1/2" and 2" setting, so in the middle is great. From the measurements, the front is now 1/2" higher than the rear and it does appear to be higher from an eye test. I will be adding a 1" block in the rear to hopefully get it back to at least level or a slight rake to the eye test. Just my initial thoughts. I will post photos over the weekend.

Here's a couple photos for reference.

1.jpg

2.jpg

GearheadSS Enthusiast

GearheadSS

Posted
Posted
On 11/12/2020 at 3:58 PM, jddealer said:

Anyone put the ride height adjustable Bilsteins on a 6.2L?  Wondering if you have a before and after measurement to see how much it raised the front.  Heard it might not raise it as much a a 5.3L because of weight?  Just wondering if you can get by with putting these on instead of the 2" spacers for a leveling kit and gain the same rise to fit tire sizes that also fit a level.  

 

In my instance, this would be for a High Country

You're only talking about 50-70 pounds difference max between the 5.3 and 6.2 in identical trucks.  

Dunn Senior Enthusiast

Dunn

Posted
Posted

Agreed, not alot of difference on weight....1/4 in if that

Offroadman00 Enthusiast

Offroadman00

Posted
Posted

Hello everyone

so i recently got a 2019 AT4 which already came with Ridge Grapplers 35x12.50 R20 along with a RC 4" lift kit

Love how the car sites, but totally hate how it rides. EXTREMELY ROUGH and everything shakes in the car include my kids carseat which is a pain in the neck

 

So...looking to see how I can smooth the ride.....

 

Will upgrading the front and back to Blisten 1500 do the trick or will I need to go with coilovers and adjustables in back?

 

cant shell out a few grant for a BDS system, so will stick with the RC one I currently have, but if I can upgrade some things to make it smoother without breaking the bank, I'd be willing to do so.

 

Any recommendations would be greatly appreciated.

Dunn Senior Enthusiast

Dunn

Posted
Posted
35 minutes ago, Thejet07 said:

I have 2” spacers on my fronts. If I installed the bilsteins at 2” would I need another alignment?


Sent from my iPhone using Tapatalk

spacers compress the shock and makes them ride in a harsher part of the travel, it also reduces the available travel and reduces ride quality....you could buy a bilstein or eibach kit and use their spring to get you to 3.5/4 ... control arm could be binding if its stock too....bigger tires dont help either so just a matter of what your willing to compromise.....you basically scrap out the RC front portion of the kit....

 

anytime you adjust the suspension height you need alignment and if truck was bought used maybe not a bad idea anyway.....

 

 

ms6040 Enthusiast

ms6040

Posted
Posted
On 4/19/2021 at 4:09 AM, LakeAnna72 said:

Thanks for sharing! I have an appointment this Thursday to have mine done and will probably  go with the 1.5 

Thanks!

IMG_4141.jpg

Please post a photo once it's done! Are you doing anything with the tires?

Msol Enthusiast

Msol

Posted
Posted


I have a few questions regarding the 5100 shocks for front and rear of my 2020 Silverado 1500 RST 2WD. 


1) If I'm not mistaken the 2wd and 4wd shocks are the same part?


2) If I am lifted with 4 inches in the front and 3 inches in the back with a Readylift kit, will this work for me? I wanted to upgrade both front and rear shocks for a better ride quality using 5100 series. Since I would be already lifted , I am not seeking any height increase just better ride handling. Will leaving the front shocks setting at 0, work for my application? 


3)Since the rear would be lifted 3 inches by rear lift blocks, will I need shock extenders for the rear shock or will the 5100 be ok without an extender?


4) Does the 5100 front shock set at 0 already have some height increase over the stock height strut (shock)?


These are my questions regarding the 5100 series shocks for my truck. 


Any help would be greatly appreciated.




Sent from my Pixel 2 XL using Tapatalk

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • BIGBOYS
      Doors lock and mirrors fold in while driving

      By BIGBOYS · Posted

      I have a 2015 Silverado and sometimes I can not get in to the truck. I use the key to unlock the driver door. Something is locking the truck when I unlock it, last night I left the truck open and this morning it was locked with the mirrors folded in. This happens while driving so it is now a safety issue. I reach down for the folding button and they open, then they close again.  Any advice, thank you,   Ed
    • Paul8556
      Headlight issue...

      By Paul8556 · Posted

      Did you ever find a resolution to this? my 2019 Silverado 1500 is showing the exact same headlights issues with the exact same symptoms.  would help a ton if anyone has any advice on this or better yet a known solution..
    • RyanbabZ71
      Gas Prices

      By RyanbabZ71 · Posted

      Wawa and Meijer here have ethanol free (88 & 89) I use for my mower and lawn equipment.  Its not much more than reg.  I paid $3.29 a few weeks ago.  
    • Atlas
      Wow I'm in a pickle. (Broke down truck) and a story.

      By Atlas · Posted

      tl; dr I've now reached the 6th floor of hell. I'm chronicling my journey for my morning readers.   Pulling the top of the intake apart was moderately easy but it involved a lot of parts, connections, and minutae. I was preparing for the new fuel lines to arrive ("nut and bolt kit" it's called). The fuel line connections are notched and held in place by the manifold and a metal plate with a T27 screw.   It's on the back of the intake, under the firewall, with little clearance, and two hard metal fuel lines in the way. I was using Franken-tools (weird combinations of 1/4 inch ratchet with/without an extension, with a bit holder for my T27) to get in there. One of my sockets and bits fell off and has yet to emerge on the floor. I lost a second setup and that's when I almost started throwing tools. But that was the point at which I had gotten traction on the Torx head, and it promptly stripped. No more traction.   I started humming "1-877-kars-4-kids" because I was about at that point. You know what? I'm $1500 into this thing and I can make it disappear just as quickly. This isn't fun anymore. I had spent a lot of time already "tidying" around the engine bay: Fixing all the "someone's been here before!" BS. The truck has been exclusively dealer- and shop- serviced and I'm reminded of why I never let other people work on my cars unless absolutely necessary.   Speaking of dealer service. This truck has a 1" stack of records going back to 1995. I put them all in an excel spreadsheet, date/mileage/description.   The CPI spider has been replaced 4 times in 85k miles. The EGR? Another 4. Multiple, multiple O2 sensors. One Cat. 4? Sets of plugs and wires, and I swear half the stack is diagnosis paperwork for "misfire, runs rough, extended crank, dies at stoplights".   GM was producing some proper crap back then. And it was still well within the era of brittle/crappy plastic. (Windows 95 was released the same month this truck was sold new, we HAD the technology!!)   There (was) a plastic shroud around the evaporator core and HVAC fan in the engine bay. I noticed a chunk of it missing so I poked at it some more and it literally shattered. Touched it some more and pieces were crumbling off. Had a good laugh. Clearly whatever plastic garbage they were using had broken down over 30 years and was literally turning to dust. That was a good half hour of using a shop vac to remove the rest of it.   Back to it.   I was going to give up for the evening but then decided I'm already level 10 pissed off at the stripped screw: G* D* it, give me my tools back -- and my JOY. We'll do this the hard way: The whole intake is coming off.   Blazer won Round II. After finally finding and accessing the 12 intake bolts and using a pry bar to unseat it from the heads, it popped loose in an explosion of gunk and grime raining down into open ports. Awesome.   6 times I reminded myself: Be careful of the temperature sender on the front of the intake.   YEAH, I forgot again and snapped it clean off in the removal. Add another $20 to the ever-growing list of new parts this thing is consuming.   The shame is, long before removing the intake, I had changed the oil in prep for Tuesday's momentous fuel line replacement that was going to be the magic fix and I'd have a running Blazer to tool around in this next weekend. The intake removal, including raining gunk, also gushed dirty coolant all over the valley. Of course it did. Welp, there goes another $35.   I now need an intake gasket set, bolt set, coolant temp sensor, another 5 quarts of oil, some RTV. Don't worry, I've already got 3 new jugs of Dexcool and a thermostat waiting. I'll fill it with clean water first to get it running, dump it, and then add the Dex later on in case... well, let's not go there. I'm only tearing this down once, next time the truck is going on Marketplace for FREE.   Oh, and I'm going to need vacuum hose for all the stupid connections placed at the rear of the engine which have since disintegrated. Come on, GM....tell me you don't do that anymore?   Oh, and the ears on the distributor where the cap screws down are both cracked. I mean, why not put a new distributor in it too. You get a distributor, YOU get a distributor, Everyone gets a new distributor!   This truck isn't out of the woods yet...I'm already questioning how much more time I'm willing to sink in.
    • William Aldrich
      Bent valve in 2025 GMC Canyon Denali - Requires engine swap at 14K miles

      By William Aldrich · Posted

      NewDude, thank you for the suggestions!    I did follow up and the dealer indicates he has an open CX case and is working with DPAC (Dealer Parts Assistance Center).   Per the dealer, GM has had a quality spill and is not providing an update for when a replacement engine will be available.

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...