Jump to content

Recommended Posts

Posted

Found a lawyer and sent the dealership and GM a final attempt to fix letter on my 2014 Sierra. Heard back from GM and they are setting it up with the dealership that I purchased it from. They could not fix it the first three times so I doubt anything will change.

 

 

Sent from my iPhone using Tapatalk

Posted

Found a lawyer and sent the dealership and GM a final attempt to fix letter on my 2014 Sierra. Heard back from GM and they are setting it up with the dealership that I purchased it from. They could not fix it the first three times so I doubt anything will change.

 

 

Sent from my iPhone using Tapatalk

 

 

Good Luck..... It took me four months from that point. I hope they treat you better than they treated me.

Posted (edited)

Ok so their are alot of pages here. And reading them makes me very parinoid so i stop reading. My 350 mile 2015 has a shake starting at 73 or 75 and goes a bit above 80. Flat expressway, 3.08 gear 18"s z71 crew. Can be minor or can shake the crap out of my arm rest of the bench, random in its intensity though usually lighter. Feels like in middle or rear of truck little feel in steering wheel. Is this the rear diff shim issue? Is their a bullitin on it to take to the dealer?

Edited by afireinside7444
Posted

How serious are some of yalls issues? Reason I ask is I seem to have a vibration right around the speeds said (69-73mph) and the steering wheel shakes up and down periodically and the passenger seat shakes a bit. Should I take it in and address it with the service dept?

Posted

So, I took mine in today. They did a forced balance on all 4 wheels. Here's the vid I took afterwards, absolutely NO difference...

 

 

Posted

Ok so their are alot of pages here. And reading them makes me very parinoid so i stop reading. My 350 mile 2015 has a shake starting at 73 or 75 and goes a bit above 80. Flat expressway, 3.08 gear 18"s z71 crew. Can be minor or can shake the crap out of my arm rest of the bench, random in its intensity though usually lighter. Feels like in middle or rear of truck little feel in steering wheel. Is this the rear diff shim issue? Is their a bullitin on it to take to the dealer?

sorry to say, from what I've read here, yes there is. I havn't been on this forum super long, but ive seen multiple people saying they have had their rear diff's rebuilt/ replaced for vibration issues

 

So, I took mine in today. They did a forced balance on all 4 wheels. Here's the vid I took afterwards, absolutely NO difference...

 

 

that sucks man, mine isn't that bad, but it still miserable to be dealing with either way. try to get them to look at some of the things previously mentioned (driveshaft, rear diff, engine for excessive AFM shake, wheels and rims for proper roundness - not just rebalancing)

hope something works for ya

Posted

Mine has been at the dealer for 3 days now. shakes just like in the vid above mostly between 70 and 75. they checked the wheels said they were all within spec but they went ahead and re balanced them anyway. they test drove it and said problem was still there. next they swapped out the rims and tires with another truck and problem still existed. then they rotated those new wheels and tires still no difference. technician took another truck for a test drive and said it did the same thing and that it must be normal for these trucks.

 

service adviser is waiting on the service manager to make a decision on what to do next. i really like my truck hope it gets fixed.

Posted

Can others take some video's and post them here?

 

I'd like to use it as supporting documentation. You can never have too much info when dealing with the dealerships, and showing this is not necessarily an isolated case may be helpful.

Posted

i will if i ever get mine back. actually i hope they fix it and i dont have to do a video.

 

i should have done a video before i brought it.

 

search on youtube there are a few already on there.

Posted

Can others take some video's and post them here?

 

I'd like to use it as supporting documentation. You can never have too much info when dealing with the dealerships, and showing this is not necessarily an isolated case may be helpful.

send me your email I will send you some videos.

Mine has been at the dealer for 3 days now. shakes just like in the vid above mostly between 70 and 75. they checked the wheels said they were all within spec but they went ahead and re balanced them anyway. they test drove it and said problem was still there. next they swapped out the rims and tires with another truck and problem still existed. then they rotated those new wheels and tires still no difference. technician took another truck for a test drive and said it did the same thing and that it must be normal for these trucks.

 

service adviser is waiting on the service manager to make a decision on what to do next. i really like my truck hope it gets fixed.

don't take normal as acceptable answer its not normal its a huge issue GM has.

 

Has anyone dealt with a GM field engineer? I have one coming next week to look at my truck.

Posted

So we got our 2014 rally 2 back after the final repair attempt with GM engineers. Unfortunately the problem is not resolved. They road forced the tires again and two were replaced which did not fix the issue. Here are some videos for you all that we've taken. The first one is our truck before the final repair attempt. The second video is a loaner they gave us. The third video is our truck after we got it back from the dealer. Have to say we are super disappointed. We love our truck so much :(

 

First video:

 

 

Second video:

 

 

Third video:

 

  • Like 2
Posted

send me your email I will send you some videos.

 

don't take normal as acceptable answer its not normal its a huge issue GM has.

 

Has anyone dealt with a GM field engineer? I have one coming next week to look at my truck.

We just got ours back from being with the GM engineers, they hooked up the PICO meter and drove it about 50 miles. They just changed out two tires. BUT our dealer has already road forced the originals tires, then changed out all four, after that they rebuilt the deferential and changed out the drive shaft. So they kind of did what they could already. Just really sucks :/ our dealership has been AMAZING to say the least and we are SO thankful they've stuck with us through all this. See my above videos for some reference.

Posted

We just got ours back from being with the GM engineers, they hooked up the PICO meter and drove it about 50 miles. They just changed out two tires. BUT our dealer has already road forced the originals tires, then changed out all four, after that they rebuilt the deferential and changed out the drive shaft. So they kind of did what they could already. Just really sucks :/ our dealership has been AMAZING to say the least and we are SO thankful they've stuck with us through all this. See my above videos for some reference.

So whats the next step?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Latest Articles

  • Posts

    • Monday looks like a good day for the dealer to test an ac issue. Hopefully it all turns out good.
    • Paid $2.72 for E85 today.
    • Welcome back! No, it definitely doesn't pass the sniff test. Even "ceasefire" needs an alternative definition these days.    $5.29 at Kroger today
    • That makes sense, and I think you are describing the real product problem. Capturing data is the easy part. If the owner or technician has to manually dig through five minutes of millisecond-level logs, the product has already failed. The device would be at the ECM harness, not at the OBD port, so I agree that data retrieval and event marking need to be thought through carefully. The way I am thinking about the architecture is: The recorder itself should not depend on a phone, app, Bluetooth, Wi-Fi, or cloud connection to capture the event. It should always keep a local rolling buffer and lock the event locally. A button, phone app, or small cabin device would only act as an event marker. If the driver feels a stumble and presses the button 10–30 seconds later, the pre-buffer has to already contain the useful data. For data retrieval, the practical options would be a sealed service USB lead, Wi-Fi download, or a phone/cabin companion device. I would not expect the owner to remove the ECM-side module or work with raw files directly. The cloud or AI side would be for interpretation, not for capturing the event. The truck may have no connection when the issue happens, so the evidence has to be saved locally first. After that, cloud processing could help decode the data, compare it against baselines, and generate a readable report. For the first version, I would keep the automatic triggers conservative and objective: driver event marker bus-off error passive voltage drop / brownout device reset FIFO or queue overflow a normally periodic message disappearing side-to-side communication mismatch, if the topology supports that For “learning normal,” I agree with your point, but I would not want to overclaim it as automatic root-cause diagnosis at first. A realistic first step would be learned baseline comparison for that specific vehicle and operating condition. For example, a value would only be compared against similar conditions: RPM range load / MAP throttle position gear / vehicle speed coolant and oil temperature battery voltage AFM/DFM state, if decoded and validated Then the report could flag things like: this periodic message disappeared compared with its normal timing this value deviated from this vehicle’s normal range under similar conditions the same abnormal pattern repeated after the same type of event the anomaly occurred together with voltage, oil-pressure, misfire, or communication changes But I would still call that “abnormal pattern detected,” not “replace this part,” unless there is enough validated repair data behind it. So the intended product would not be “here is a huge log.” It would need to be an event package: what triggered the capture how much pre/post data was preserved what changed before and after the event whether the device itself reset, overflowed, or saw a bus error selected graphs around the event raw data only as supporting evidence From your perspective, what would make this kind of report useful instead of just another datalog? For example: What are the top 5 parameters or events you would want highlighted first? Would you trust a learned baseline for that specific vehicle, or would you prefer fixed thresholds? How much false-positive flagging would be acceptable before you stopped looking at the reports? What would a one-page report need to show for an independent shop to take it seriously? For misfire, AFM/DFM, oil pressure, or U-code complaints, what would you want the tool to flag automatically?
    • 2024 Silverado 2500 HD LTZ grille no camera Parts list   84603331 84913656 84913657 84913654 84913655 84911567 84911568 85646092 85646093 85797921 85797922   11570637  x10-15   grille/bumper bolts 11546500  x10      grille clips 11571006  x10      push/retainer clips 11546454  x6       nut retainers 11611609  x6       M5 bolts 11610700  x6       molding/trim retainers
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...