Jump to content

Recommended Posts

Posted

Just for information purposes, where is everyone's truck produced? is there any correlation to a plant? Mine was made in Mexico, is it also happening at the Indiana plant?

Posted

This is my problem also, GM not co-operating dealer is useless started legal actions to get it fixed or buy back, no more pissing around with this nonsense.

You are not alone in this, what is your build date of your truck.

build date 9/13

Posted

Thanks for the recap and going out of you way to give us all the details! The question is, why do some vibrate and some don't? If it was inherit in the design, all of them would do it not just a handful. It has to be bad parts etc. I still think the driveshaft is culprit and would like to see the results of going to a driveline shot and having then balance it and/or check the run out and yokes etc.

 

in a mechanical system there are always tolerances for every part in it and certain ranges deemed acceptable. In something with as many parts and moving parts as a vehicle no 2 will be the same. Add to that assembly methods and different plants, techs, engineers doing measurements you can have variance all over the board.

 

The design of the frame, engine, rear end, drive shift etc. Something is obviously too close to the limit when it comes to natural frequencies of vibration. When certain parts end up on the right end of the tolerances, and probably a combination of other factors such as assembly methods u get the vibrations showing up in some and not others.

 

Talking from experience in mechanical system design. I have a bachelor's in mechanical engineering and am a licensed professional engineer in multiple states.

Posted (edited)

Totally agree with the tolerances. Something is right on the edge. What gets me is the fact that my 2013 for bought back by GM for the same vibration that I now have in my 2014. So some of the parts have to be similar in the two trucks that are causing it. I might just go to an independent driveline shop and see what they say just so a few of us can rule that out if it isn't that and if it is, it's a relatively cheap fix. If anybody beats me to the driveline shop please let me know what you come up with!

 

 

Sent from my iPhone using Tapatalk

Edited by hotrodz37
Posted

I'm on a staycation all next week watching my 14 week old son so Im really going to try and make it to a drive line shop sometime during the week. The tires on my truck were @ 42 lbs from the factory and I put them @ 32 & the vibration is almost gone. I still think its the shaft and maybe shitty u joints as others keep saying. I'm going to have it balanced as well as new u joints.

Posted

This is my problem also, GM not co-operating dealer is useless started legal actions to get it fixed or buy back, no more pissing around with this nonsense.

You are not alone in this, what is your build date of your truck.

Good move

Posted

Well I was talking to a family friend tonight who also has a 2014 silverado, crew cab long bed LTZ Z71, 5.3L and 3.42 axle ratio. Odometer is approximately 16,500 miles. He has developed a vibration at 70+ mph. He told me that a friend of his is a very knowledgable GM guy and that his friend told him that GM has a history of vibration problems that dates back years and that there is a specific thing to look out for if you have vibrations. He couldn't remember what it was but said he'd ask him and let me know. I plan to bug him relentlessly until I hear what this other guy has to say!

Posted

Do they make Bilstiens for the 14 yet or are they the same as the 2013?

Yes and no.

The crappy stock shocks / struts on the High Country are Bilstiens.

 

There are no after markets released yet.

Posted (edited)

Yes and no.

The crappy stock shocks / struts on the High Country are Bilstiens.

 

There are no after markets released yet.

GM doesn't put Bilsteins on any vehicle they make and Bilsteins aren't crappy either. They're one of the best shocks you can get actually.

 

The current Z71's come with monotube Ranchos. Everything else comes with Tennecos. Tenneco makes Rancho and Monroe shocks. I'm not 100% sure but I think the Z71's are the only shocks that are monotube design. The rest of the trucks are twin tube design.

 

And to answer the original question, no Bilsteins aren't available for these trucks yet. Hopefully they come out soon though.

Edited by Silverado-Hareek
Posted (edited)

For what it's worth. I have test driven two denali trucks to replace my all terrain (due to other issues). Neither of which had any vibrations. I will say it was odd that the tire pressure on both trucks were set to 37-41 PSI.

Both had build dates later than 4/22. Hopefully it was just a bad batch or whatever...

Edited by Trackermi
Posted

About 12 years ago I picked up from the dealer a new Silverado for my neighbor and in driving it to his house I noticed a vibration at about 60mph. I told him about the vibration and after tire swaps, balancing, etc, etc he had Chevy buy back his truck under the Florida Lemon Law. Even back then some Silverados were called 'Shakearados'. His new truck after the buyback did not vibrate.

 

Maybe the U.S.Gov will have GM spend more effort to find the cause (and fix) for this long term issue:

http://www.thedailybeast.com/articles/2014/05/17/g-m-becomes-government-motors-again.html

Posted

Yes and no.

The crappy stock shocks / struts on the High Country are Bilstiens.

 

There are no after markets released yet.

 

The answer is yes, they do have aftermarket shocks http://www.gorancho.com/shock_lookup.php?cat=qll&shock_type=quickLIFT%E2%84%A2+Loaded&year=2014&make=Chevrolet&model=Silverado+1500&drive=4WD&x=35&y=7

Some of the best shocks available and the adjustability is the greatest thing since sliced bread

 

Also, the Bilstiens are a good shocks.

Posted

So I have been reading everyones post on vibrations. My 2014sierra has the same issue been to the dealer 4 times plus all the ridiculous recalls. They have changed my tires twice balanced once, and now I have Bridgestone tires problem still presist. Not to mention my radio goes in and out, and under acceleration the truck will on occasion choke outand jerk like hell. Has any tried to claim lemon law yet? I paid 40k for a truck that rattles worse then my 02 with 498 k on it. Just not satisfied I have no choice but drive it now with18, 000 vibrating miles on it. I wish they would give me another to try again..

So I have been reading everyones post on vibrations. My 2014sierra has the same issue been to the dealer 4 times plus all the ridiculous recalls. They have changed my tires twice balanced once, and now I have Bridgestone tires problem still presist. Not to mention my radio goes in and out, and under acceleration the truck will on occasion choke outand jerk like hell. Has any tried to claim lemon law yet? I paid 40k for a truck that rattles worse then my 02 with 498 k on it. Just not satisfied I have no choice but drive it now with18, 000 vibrating miles on it. I wish they would give me another to try again..

So I have been reading everyones post on vibrations. My 2014sierra has the same issue been to the dealer 4 times plus all the ridiculous recalls. They have changed my tires twice balanced once, and now I have Bridgestone tires problem still presist. Not to mention my radio goes in and out, and under acceleration the truck will on occasion choke outand jerk like hell. Has any tried to claim lemon law yet? I paid 40k for a truck that rattles worse then my 02 with 498 k on it. Just not satisfied I have no choice but drive it now with18, 000 vibrating miles on it. I wish they would give me another to try again..

Posted

GM doesn't put Bilsteins on any vehicle they make and Bilsteins aren't crappy either. They're one of the best shocks you can get actually.

 

The current Z71's come with monotube Ranchos. Everything else comes with Tennecos. Tenneco makes Rancho and Monroe shocks. I'm not 100% sure but I think the Z71's are the only shocks that are monotube design. The rest of the trucks are twin tube design.

 

And to answer the original question, no Bilsteins aren't available for these trucks yet. Hopefully they come out soon though.

 

I will let the GM Engineer know he is wrong. Thanks

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Latest Articles

  • Posts

    • Folks, Have a great new 2026 WT  (std cab, 2.7/4WD) w/base 40/20/40 mech adj bench "fake buckets"  (with lower and upper center console) heavy vinyl seats.  Overall the seats are very comfortable and the vinyl is heavy and appears less likely to 'split out'. Am very tall (6'5")  + a bad back/osteporosis/former hyperparathyroidism so ease/range of movement is a bit restricted.  The truck rides a bit high and I use a nerf step bar w/my left foot to step in, then I put right foot/leg in, drag my butt in  & get seated.  Worked fine in my 2018 RAM quadCab. But I end up dragging my butt over the left raised sidecushsion area of vinyl seat, and due to texture there's fair amount of traction on slide inward.  (ArmorAll didn't improve.) If the seat were even ~1/2" - 3/4" lower it'd be helpful, but base seats just have the forward/backward underseat bail and the side lever for tilt which really doesn't affect seat height.   I really don't want to 'de-puff' the left side sidecushion forming the  fake 'bucket'. I know one company sells 'seat elevator blocks':  but is there a simple way of lowering the height of the driver seat instead?   Thanks Bill W San Jose  
    • I have a basic 2026 1500 WT  (2.7L/4WD reg cab shorttbed). Comfy, generally happy with electronics/radio - but is there a way I can add switches to steering wheel right-side position (curr. empty) so I can adjust volume, push phone button to voice dial, etc? Bill W San Jose  
    • The curb weight on a 1 ton crew cab long bed is around 7k lbs.  Now, I don't know where you went to school but 9k is not more than 2x 7k lbs. More than 2x 7k lbs would be 14k+.   With that said, obviously yes you're going to feel a 9k lb trailer when slowing down.  I already said, when accelerating.  When changing lanes?  No.  But if you look at the context of what was quoted, the original person said, "after a mile or two..." which means that would be after the accelerating portion and you're driving a generally steady pace.  Please do learn to read and comprehend.
    • So I purchased the Range unit for my 2026 and I am seeing different locations suggested for the ECM . Can anyone confirm wither under hood, left side or right side or behind the wheelwell?
    • Like I've said before. Di and Carbon buildup is not that big of a concern. Engine had minimal buildup, and that engine was obviously not super well maintained. Do regular oil changes, and you're gtg as long as the rest of the truck lasts. Also, the High Pressure FP that people ****** about, but can't tell you why.  Now, I wish they'd trash the variable oil pump. No real world issues with them, but I'll gladly eat whatever miniscule MPG it's saving me in favor of more oil at all RPMs.    Curious to see his assessment of the 7.3 compared to the 6.6. I expect he'll praise the port inj, but from a structural standpoint, the 6.6 is as robust as any engine out there.    Not to take away from the 7.3. I feel it's equally as good as the 6.6.     As to heat on the rear cyls, I'd have to see numerous examples before I'd say it's an issue. Especially not knowing the history of that engine. For all is known, they could have blown a rad hose, and ran it hot, and the 2 rear cyls may be the first to get hot in a low coolant situation, but not be an issue aside from that. 
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...