Jump to content

Recommended Posts

Posted

I just had a wild idea. Does anyone here have access to a dyno machine? Put the truck on it, take it up to speed and see if the vibration persists, then try it in 4 wheel drive. Id be easier to get a camera under there with the truck on a dyno.

Posted

My 2014 GMC Sierra SLT shakes/vibrates when I tow my travel trailer. It has done it since new when I took it out with only 150 miles on the truck. If I ease into the throttle you don't notice it but if your start from a dead stop and hammer the throttle it will shake through the firs few gears. Other then that issue I don't notice a shake any other time. I am hooking up my 27' travel trailer in the morning and have an appointment with my dealer to check it out. It is definitely something related to the power train. If I never towed I wouldn't have know about the issue. I let you know what they say.

Posted

Well, after my buy back of my 2014 c/cab sierra all terrain I bought a Ram eco diesel truck.

My ram is at the dealer for a small paint defect repair, and they rented me a vehicle which happened to be a 2014 suburban which has a shudder and moan, and slight vibration at 40mph-55mph like my truck had.

This suv has the 5.3L v4 fuel mangement and 6speed with 3.42 gears?

With out a doubt I am convinced this problem is the transmission torque converter or pump or the out put shaft bearings.

This is why GM not willing to admit there is an issue, while they quickly roll out their 8 speed trannys.

Just my humble tech opinion.

Posted

I just had a wild idea. Does anyone here have access to a dyno machine? Put the truck on it, take it up to speed and see if the vibration persists, then try it in 4 wheel drive. Id be easier to get a camera under there with the truck on a dyno.

Guys have mentioned this before but I'm not sure if anyone has actually tried to diagnose the vibration/shake on a Dyno.

Posted (edited)

Well, after my buy back of my 2014 c/cab sierra all terrain I bought a Ram eco diesel truck.

My ram is at the dealer for a small paint defect repair, and they rented me a vehicle which happened to be a 2014 suburban which has a shudder and moan, and slight vibration at 40mph-55mph like my truck had.

This suv has the 5.3L v4 fuel mangement and 6speed with 3.42 gears?

With out a doubt I am convinced this problem is the transmission torque converter or pump or the out put shaft bearings.

This is why GM not willing to admit there is an issue, while they quickly roll out their 8 speed trannys.

Just my humble tech opinion.

I haven't seen any 2015 6.2L 8 speeds available for purchase but there's definetly a lot of 2015 5.3L 6 speeds with 3.42. So their not rolling them out that quick.

If you go to carsforsale.com you can view almost every new vehicle on any lot in the US.

 

Edit: I also believe it to be the transmission in many of these trucks.

Edited by 15LTZZ71
Posted

I just took my sierra in today to the dealer for the vibration problem,just got it back from dealer last week for the same problem plus a few other issues. I went for a ride with service manager and got about 3 blocks away from the dealership and he said ok thats good enough take it back to the dealership. My truck was built 7/13 so its an early build and you sure can tell after a five minute ride in it. Im gonna give the dealership one more chance to fix this vibrator with wheels then I will have to take this further.

Posted

I just took my sierra in today to the dealer for the vibration problem,just got it back from dealer last week for the same problem plus a few other issues. I went for a ride with service manager and got about 3 blocks away from the dealership and he said ok thats good enough take it back to the dealership. My truck was built 7/13 so its an early build and you sure can tell after a five minute ride in it. Im gonna give the dealership one more chance to fix this vibrator with wheels then I will have to take this further.

 

I hope they treat you proper, and make things right!

Keep all paper records each time, and keep a log book of notes of attempts to resolve your issue.

Good luck mine didn't get fixed no solution found bought back.

Posted

I hope they treat you proper, and make things right!

Keep all paper records each time, and keep a log book of notes of attempts to resolve your issue.

Good luck mine didn't get fixed no solution found bought back.

I have 14k worth of dealer installed up grades on my truck so they need to fix it. Im not gonna lose my a** cause they cant figure out what the problem is.

Posted

So the technician said there is defiantly an issue and he is talking to GM engineers before proceeding. He thinks it has something to do with axle wrap, the driveline or the rear end. It only shakes when I have a load on it and accelerate hard through first and second gear.

Posted

I picked up a 2014 silverado custom sport last month. 5.3 L - 3.42 rear. It came with polished 20s and Continental Crossconnect eco plus tires. After about 500 miles I notice a vibe in the steering at around 75 mph. Not real bad but it's there. Also cruising around local I sometimes get a vibe in the steering but not always. Most of the time the truck feels smooth. I only have 1200 miles on the truck so I wanted to see if it get worse or better. Also, was wondering if any one else is running the Conti's and if your getting any vibration with them.

Posted

I picked up a 2014 silverado custom sport last month. 5.3 L - 3.42 rear. It came with polished 20s and Continental Crossconnect eco plus tires. After about 500 miles I notice a vibe in the steering at around 75 mph. Not real bad but it's there. Also cruising around local I sometimes get a vibe in the steering but not always. Most of the time the truck feels smooth. I only have 1200 miles on the truck so I wanted to see if it get worse or better. Also, was wondering if any one else is running the Conti's and if your getting any vibration with them.

What the heck are "Eco plus" tires? Low rolling resistance or something? Somewhat of an oxymoron with heavy 20 inch diameter rims.

Posted (edited)

Reading all of this (not really, but I did read a lot) reminds me of a 2000 Silverado I had once. Took me almost a year to get the dealership to replace tires on it. Shaked like the dickens at highway speeds. Turns out it had 3 out of round tires on it. 3!!!! Goodyears.... The first time they finally replaced, they did with Goodyears, and it still shook. Then I got firestones (off brand named versions) and it drove like a dream from then on.

Edited by Nargg
Posted

I have 14k worth of dealer installed up grades on my truck so they need to fix it. Im not gonna lose my a** cause they cant figure out what the problem is.

 

I assume "they" is the dealer as GM is not responsible for non-OEM modifications (even if done by an independent dealer).

Posted

I love the looks on my truck just hate driving on the freeway. Should have not bought it.

Posted (edited)

I have 14k worth of dealer installed up grades on my truck so they need to fix it. Im not gonna lose my a** cause they cant figure out what the problem is.

right before your arbitration hearing they will call you and offer a full purchase value trade-in credit towards another truck and you pay any additional cost if its a higher price.

 

at that time you can make a deal for them to transfer all your upgrades to the new truck and I would "assume" they will absorb the labor cost but then maybe not and you will have to pay the labor but that's still a decent deal.

 

short of that its up to you to remove everything yourself and then sell it or buy another truck you can use them on.

 

you are not going to get a penny more from GM then the cost of the truck the way you bought it in stock condition, consider the rest lost money unless you can remove it without leaving any damage to the truck from removing it because scratches and holes and anything else will all be depreciated at full retail body shop repair prices.

Edited by keakar

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Latest Articles

  • Posts

    • Hey thanks yall for the info. It apparently was the key fob - the "reserve" key fob works just fine. Yall were all over it. Great input! JRD
    • I just bought one of these.   https://www.topdon.us/collections/diagnostic-tools/products/artidiag-pro   Yeah, it`s got a cable. $250/year after 2 years. Do I want more? Yep. But, I`m not working any more and can`t afford a whirlpool in my tool box.
    • Why don't I have a good scanner? I've always wanted one when I've needed one.   My latest reading says I don't need to do a relearn on the ckp sensor on a 1995 with OBD 1.5. The relearn is prescribed for the later-model 1995's which shipped with actual OBD II when GM completed the transition in prep for the 1996 MY. I need to confirm that. Did you know forums are disappearing? Knuckleheads on Facebook... it's not the same. It's just not.   So, scanners. Again, shooting myself in the foot for having eBayed my Snap On MT2500 "brick" with all the adapters. Not that I couldn't buy another but those are getting quite old, and mine wasn't new enough to work on 2000's vehicles.   Damn it (as I'm scanning my email between paragraphs here). Did you know there's a 2000 Jimmy 2-door on BaT that's ending this morning? It's local. I want it. 14k miles. Absolutely beautiful.   Back to scanners. MT2500's are old. Solus, now that could be a contender. There's a ~2008 Verus with a system error that's basically new in box for cheap. Hmm...I'm not sure about a scanner that runs an archaic version of windows (95 or CE, I can't tell).   I want the ability to reset and rotate TPMS, test individual modules, bleed ABS, electronic parking brake controls for servicing brakes, relearn procedures and other bidirectional controls.   Snap On does an MT2600. It's a new model as of last year, marketed as their "entry" scanner. Entry? Only where $1900 gets you through the doorway plus, I'm guessing, $1000/year if you wish to keep it current. So goes scan tools actually designed for production environments. Want decent products with excellent support, you pay for it.   Everyone is raving about Autels and TopDons and Foxconns and all these newer brands that are selling the $500 "prosumer" scanners for backyard hacks like me. They're tempting...honestly. Updates are cheaper, base prices are remarkably cheaper... And you get to deal with bugs and translation whoopsies and, well, just don't use it on anything expensive, OK? Having a dealer replace an ECU because it needs to be re-imaged after an adventure in scanning is no joke. But I think most people are getting by OK with these units.   eBay on a scratch-and-sniff pro-model oldie, a shiny new TopDon, or???   God dang it, I can't stop looking at this Jimmy. I'm ready! I'll Bring The TRailer! It's beautiful.
    • I removed the OE running boards.  It looked so much better.  I wish I took them off a long time ago.     I had to put something back on for my wife.  I wanted Westin Sure Grip Running Boards but they are very pricey, like $600 plus.  I was going to go with the Ionic 41's like I had on the 2019 Silverado but went with Westin Outlaw Drop Steps instead, about $200 cheaper.  They are sturdy and functional but not super crazy about the look, but it works.  
    • It's all a crock of 💩
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...