Jump to content

First time changing oil on this truck

TwentyEighthNight
 Share

Recommended Posts

TwentyEighthNight Enthusiast

TwentyEighthNight

Posted
Posted

Just changed the oil on my 2014 gmc sierra 4.3l. It required six quarts of oil which is what i used but now i am afraid if its overfilled or not. Its a completely different reading than what it was before the oil change. Althought its not above the hashmarks there are 2 dots on there which I’m not sure if those are the oil level indicators or the hashmarks are the oil level indicators. The dots are kinda hidden which is why I’m not sure if those even are oil indicators dots. Im really hoping i filled it up correctly and wont ruin the engine by overfilling the oil. I installed a fumoto valve so it could be easier to drain excess oil. I do note there was a metallic ticking noise that was present before the oil change but disappeared afterwards.

following picture (2) is before the oil change one of each side of the dipstick56E61FB4-2BBA-4F84-A7CC-EE86045CBF53.thumb.jpeg.f7d35d806fe6e92c13a48d448cc5bbbb.jpeg8A47DA80-9759-4703-B6A6-644903920943.thumb.jpeg.375c86f21fa05a473a360d4087ac8a85.jpeg

 

The next two fuller looking ones are after the oil change one for each side of the dipstick

E1E6C592-4D5D-47B8-959E-5C559FCE9513.thumb.jpeg.de2c8293d592f5924f53d94b9184817b.jpegFABC7973-C973-4CC6-B931-D7437B560C1B.thumb.jpeg.23de88d766ca884f1cef927cc91dcf4d.jpeg

TwentyEighthNight Enthusiast

TwentyEighthNight

Posted
  • Author
Posted
12 minutes ago, steelerdude15 said:

It looks fine to me. You can also check the owners manual and it will show you how to read that particular dipstick.

Thanks for your comment! I did check the owners manual but it had a different type of dipstick with 4 dot indicators and no hashmarks so it just made it more confusing.

Z45 Senior Enthusiast

Z45

Posted
Posted

The cross hatched area is approx. 1 qt range. 

  • Like 1
diyer2 Senior Enthusiast

diyer2

Posted
Posted

I believe the 1 quart markings on the dip stick have been a standard for years. Dots, hash marks etc. equals 1 quart.

KARNUT Senior Enthusiast

KARNUT

Posted
Posted

I always believe the marks are there to make it easier to read fresh oil. The top is full the bottom is a qt low. Whenever I changed my oil I put what’s called for and move on. When changing other fluids like transmission I measure the old coming out and put that amount in. Anywhere in the hash marks your fine. Even a qt low your fine. When I first got the CRV I check the oil at every fill up it was always different. 3000 miles later at home it was full exactly like when I left. 

  • 2 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • Atlas
      Gas Prices

      By Atlas · Posted

      87 down as low as $5.14 here... winning!
    • Atlas
      Wow I'm in a pickle. (Broke down truck) and a story.

      By Atlas · Posted

      Progress... sort of.   Intake is disassembled, spider is out, fuel lines removed. Used a torch on the stripped screw with the lower intake off, much easier when I've got the intake sitting on my workbench, I made it talk. Walked right out with a pair of vice grips once it was nice and toasty hot.   New parts are piling up on my service cart waiting to be installed. Distributor, temperature sensor, new gaskets, fuel line kit, themostat, water neck.   My new pickle is I don't want to spend $600 on a replacement spider. I'm not sure IT is bad. I'm probably splitting hairs. Or it's $300 to send mine away and another 3 weeks of the truck just sitting. I have half a mind to assemble everything with the old spider to see if I can get away with just replacing the fuel pressure regulator to be safe. The obvious issue was the gushing high pressure fuel line which will be replaced. Getting to the spider really isn't that hard, and now I know what I'm doing , swapping it would be a breeze should it absolutely need one. Stupid, or smart?   The part that gives me pause is replacing the distributor. Well, it's already out. And I didn't mark it, whoopsie! Engine was at TDC when I removed it, I know that, so upon correct reinstall the metal tip on the rotor should point to the TDC mark on the distributor because that's where it was pointing on the old distributor. Worst case I'm a tooth off and have to re-stab it.   But then, what? I assume the truck will start. It doesn't appear the timing can be set. Here's the problem: These distributors can't be rotated but a degree or two, by design. What I read is Cam ****** needs to be -2 to +2 degrees, ideally at 0 (and checked/set above 1000 rpm). There should be enough wiggle to get that properly set, but checking the reported value is another potential issue. My Actron 9185 scanner says it supports enhanced GM PIDs and Cam ****** is one of them but it's unclear that I'll be able to correctly see it over OBD 1.5. I can see why people end up junking these things with life left in them. They're an absolute nightmare with tweener-year diagnostics/electronics and unobtanium parts.   Fingers crossed it starts and idles nicely. There can be hope, right? I'ma buy a lottery ticket the same day just in case.   Next steps..DO IT. I have not installed an intake before so I've been reading and watching a lot. Some say NO RTV except on china walls, some say DO RTV on water ports but not fuel/air intake. 1/4 or 3/8 bead on China walls? I think my strategy will be, obviously, RTV china walls with overlap on the gasket corners. Chapstick-style RTV the water ports. Leave intake ports dry. The only set of intake gaskets I could find locally are Edelbrock performance gaskets (uh...for an asthmatic 190hp V6? LOL) so we'll see how they do.   #NoToolLeftBehind. It took an hour, but my recovery mission for my deep 10mm socket was successful. It had rolled down the bellhousing and wedged itself between what I think are the fuel lines? I couldn't see it at all, but with a junk antenna I had laying around, I blindly went poking/sweeping for it, heard it clink, raised the truck, and caught a sliver glimpse of chrome with a flashlight way up there in Narnia. I had pushed it farther along the lines holding it captive, but within access of severely improvised tools, poking and cursing at it to finally knock it free to where I could get a fingertip on it to bring it home.    Not much to see.      
    • RyanbabZ71
      Gas Prices

      By RyanbabZ71 · Posted

      Thats crazy considering im right next door (Indiana)
    • Black02Silverado
      New Retail & Commercial Promo

      By Black02Silverado · Posted

      For a limited time, retail and commercial accounts receive an AMSOIL Vinyl Tool Tray with their order of $500 or more when they use code TRAY726 at checkout. The promotion runs through July 21, 2026.   Order at https://syntheticadvantage.com   Want to use AMSOIL in your business or sell at your store, apply here.  https://www.amsoil.com/business-opportunities/?zo=521390  
    • KARNUT
      2027 GMC Sierra: Official Discussion

      By KARNUT · Posted

      It wouldn’t have happened if the government hadn’t mandated outrageous fuel mileage standards. It does very little for the consumer. It adds cost. Back during Covid there was a chip shortage. They gave a rebate for your truck if it didn’t have the chip to turn on cylinder deactivation. It was 50$ because at best you may see 1/2 a mile increase per gallon. Splitting hairs each fuel mileage trick wasn’t mandated. The government doesn’t do the engineering work and say use this until it’s already in use and they like it. The fuel mileage was mandated. And those add ons the results. There’s a mandate and they are the results.

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...