Jump to content

Recommended Posts

Posted (edited)

This is my opinion only, but this is what GM should do: If they cannot fix your truck under waranty they should buy it back at full purchase price. Then they should take these trucks apart at one of their reaserch and development facilities, and find the root cause of the vibration problems and eliminate them. Then they would also have low mileage trucks, now repaired to sell at a good price to recoup their losses to some extent. This would be fair to everyone and would help GM to avoid similar pitfalls in the future.

Edited by pm26
  • Like 4
Posted

This is my opinion only, but this is what GM should do: If they cannot fix your truck under waranty they should buy it back at full purchase price. Then they should take these trucks apart at one of their reaserch and development facilities, and find the root cause of the vibration problems and eliminate them. Then they would also have low mileage trucks, now repaired to sell at a good price to recoup their losses to some extent. This would be fair to everyone and would help GM to avoid similar pitfalls in the future.

They'll buy it back and then put it on the used car lot for someone else to deal with.

Posted

They'll buy it back and then put it on the used car lot for someone else to deal with.

I meant buying them back voluntarily, not only when forced by the consumer protection laws.

And repairing them before selling them to another unsuspecting sucker. That's the only ethical thing to do.

  • Like 2
Posted

Just had 305/55/20 nittos, and xd wheels put on. Vibration gone, AGAIN, we'll see if it comes back, AGAIN

Posted

I meant buying them back voluntarily, not only when forced by the consumer protection laws.

And repairing them before selling them to another unsuspecting sucker. That's the only ethical thing to do.

 

I know what you meant.... and I agree with you that it makes logical sense to buy them back so they can figure out what is causing the vibration. The reality is that GM thinks it's acceptable for a truck to shake on the highway since they continue to tell me that it is "road input" or "a normal operating characteristic of the vehicle" or "performing as designed." But they won't give you a yes or no answer when you ask them if it is safe to drive. They will use the buzz words mentioned above and talk in circles until you end the call.

Posted (edited)

I don't know why everybody thinks it's ONE thing that is causing everybody's problems. It's likely that everybody is experiencing different problems - or several different problems. There is not one magic fix that will fix everybody's tuck. For some people it's tires. For some it'll be shocks, driveshaft, tranny, rear end, axles, etc. Each of you just need to be pushy and persistent to get the dealer and/or GM to resolve. If they can't/won't fix it, push for a buy back. There are several instances on this site of buy backs, so it does happen if you truly have a problem. But if you just sit around and wait and complain, your truck will never be fixed. I know dealing with the dealership and GM is a hastle, but it you want it fixed or a new truck, you have to do it. Otherwise, deal with it or trade your truck in on a different one.

 

And I'm sorry to those who think otherwise, a vibration is not a safety issue that will prompt the NHTSA to get involved.

Edited by Black03Yukon
  • Like 2
Posted

I don't know why everybody thinks it's ONE thing that is causing everybody's problems. It's likely that everybody is experiencing different problems - or several different problems. There is not one magic fix that will fix everybody's tuck. For some people it's tires. For some it'll be shocks, driveshaft, tranny, rear end, axles, etc. Each of you just need to be pushy and persistent to get the dealer and/or GM to resolve. If they can't/won't fix it, push for a buy back. There are several instances on this site of buy backs, so it does happen if you truly have a problem. But if you just sit around and wait and complain, your truck will never be fixed. I know dealing with the dealership and GM is a hastle, but it you want it fixed or a new truck, you have to do it. Otherwise, deal with it or trade your truck in on a different one.

 

And I'm sorry to those who think otherwise, a vibration is not a safety issue that will prompt the NHTSA to get involved.

You're right.

Posted (edited)

I don't know why everybody thinks it's ONE thing that is causing everybody's problems. It's likely that everybody is experiencing different problems - or several different problems. There is not one magic fix that will fix everybody's tuck. For some people it's tires. For some it'll be shocks, driveshaft, tranny, rear end, axles, etc. Each of you just need to be pushy and persistent to get the dealer and/or GM to resolve. If they can't/won't fix it, push for a buy back. There are several instances on this site of buy backs, so it does happen if you truly have a problem. But if you just sit around and wait and complain, your truck will never be fixed. I know dealing with the dealership and GM is a hastle, but it you want it fixed or a new truck, you have to do it. Otherwise, deal with it or trade your truck in on a different one.

 

And I'm sorry to those who think otherwise, a vibration is not a safety issue that will prompt the NHTSA to get involved.

 

Yes, I agree, but you shouldn't act like you haven't complained also.

 

Edit: let people complain, they are just venting their frustration like we all do from time to time. I didn't know this was a "do not complain forum" or have the rules changed/

Edited by 14LTZZ71
Posted

Yes, I agree, but you shouldn't act like you haven't complained also.

 

Edit: let people complain, they are just venting their frustration like we all do from time to time. I didn't know this was a "do not complain forum" or have the rules changed/

No, people are free to complain all they want. I never said they couldn't. Only that it won't fix anything.

Posted

Any idea if vibration on this could be related?

http://www.gm-trucks.com/forums/topic/163658-difference-in-rear-height/

I don't think so. The bed on mine sits 3/4" higer on the drivers side. All 3 pickup trucks that I've owned came from the factory with beds that sat higher on the drivers side. They don't do it because the fuel tank is on that side either because with a full tank of fuel it still sits 3/4" higher. I don't think its related to this issue.

  • Like 1
Posted (edited)

Recent events

I was coming off the highway to off ramp, slight upward grade and traffic light was green slowed down and turned left to slight upward grade.

As I started to accelerate and turn left my truck begin to shudder and felt like the transmission slipped and the rear axle begin to bind up some what. My transmission fluid was reading 195f by the trucks readings.

I do not have any vibration at or above 70mph rides like glass.

 

I am working with GM right now to have my truck sorted out, unfortunately it has taken legal action to get them to do anything or take my complaints serious.

 

Tires have been replaced, balanced, driveshaft replaced, rear end is next to be replaced, radio replaced, seat assembly, rust issue on frame.

So yes I have been patient, and still no fix and vibration getting worse. Transmission shudders from 1-2 shift and worse when warm and up hill grade.

Edited by 2strokesmoke
Posted

Recent events

I was coming off the highway to off ramp, slight upward grade and traffic light was green slowed down and turned left to slight upward grade.

As I started to accelerate and turn left my truck begin to shudder and felt like the transmission slipped and the rear axle begin to bind up some what. My transmission fluid was reading 195f by the trucks readings.

I do not have any vibration at or above 70mph rides like glass.

 

I am working with GM right now to have my truck sorted out, unfortunately it has taken legal action to get them to do anything or take my complaints serious.

 

Tires have been replaced, balanced, driveshaft replaced, rear end is next to be replaced, radio replaced, seat assembly, rust issue on frame.

So yes I have been patient, and still no fix and vibration getting worse. Transmission shudders from 1-2 shift and worse when warm and up hill grade.

Either the GM engineers are just as confused as everyone else when it comes to this issue or GM has too much s_ _ t on their plate right now to worry about these issues. I hope they get you taken care of in a proper and ethical manner.

Posted (edited)

Either the GM engineers are just as confused as everyone else when it comes to this issue or GM has too much s_ _ t on their plate right now to worry about these issues. I hope they get you taken care of in a proper and ethical manner.

I'd put my money on the second option.

 

The shake is not the end of the world for me, but it's hard to stand by a product that comes with a built in massage/coffee mixing feature not advertised that I didn't want lol. I'll mention it when I go in for my oil change along with why they didn't put the screws in my rear handle which pulled off when a passenger climbed in. Besides I don't do 70mph very often for obvious reasons :P

 

It's more of a piss-off than anything. No one wants to have their friends in their new truck and have a shake like mine and then be told you should have bought a Ferd.

Edited by RageMonkey
Posted

I have a 2014 Chevrolet Silverado 1500 4x4 crew cab standard size bed with 20" Goodyear tires. I was starting to think I was the only one with this problem. I have been having the same experience with vibration at varied speeds around 75 to 85 mph. I took it back to the dealership about the 2nd week of ownership and they said there was a flat spot on one of the tires, so they replaced it with a new tire. Everything was fine until I took it in for the 1st oil change and tire rotation a few months later. I noticed right a way that it had a vibration again but even worse no matter what road I was on. I took it back a couple days later and they experimented by exchanging new tires from a new vehicle on their lot and said the ride was better. However, they said Chevrolet would not pay for 4 new tires for my truck so they removed them and put my original tires back on. When I picked it up, they told me it was solved by putting different amounts of air (nitrogen) in the tires(less in the back tires). I'm sorry, but that is not acceptable. Besides all that, sometime at the dealership, the plastic piece on the lower front of my truck got dented in!! They brought that to my attention when I picked the truck up! It wasn't there before!! I just figured claim it on my insurance! I have another appointment at a different dealership in town this Friday. I really hope to get this problem solved. I will post my results.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Latest Articles

  • Posts

    • I have a 2024 Chevy Silverado 2500 with the 6.2 liter engine, Vin: 2GC4YME79R1273849, with 27,437 miles. Recently we took a trip from Candor, NY to Townsend, TN pulling our fifth wheel, when I got close to the Townsend, TN area The truck gave me a message of low oil. I checked the dip stick and found it was 2 quarts low. Today, August 27, 2026, I had the oil changed and the technician Found the truck was very low on oil.  Is there a Recall for this? What is my recourse for this issue? Do I call the dealer where I bought it or any chevy dealer?   Robert Strickland 292 Owego Road Candor, NY 13743 352-502-6588 [email protected]
    • We understand the importance of understanding how your Sierra performs, @SoCal Angler. Our team would like to gather the proper details to assist you with your inquiry about your truck's automatic braking. When you have a moment, please visit: https://s.chevy.com/support-request and fill out the request form with pertinent details. This will ensure your request is routed correctly so we may take a further look. We will keep an eye out for your outreach.
    • That is the funnel kit I bought and for being here in Canada I did get a better deal than what other sources were charging through a certain supplier in town that sources more directly and they ordered it for me. There are other items now on the market which would be perfect as well but this has worked well which was the hope when I bought it. I mentioned the Amsoil quart bottles as they have that squarish shape up top and it props nicely on the rim of the opening without falling into the funnel so I can leave them sit and drip a bit. You may have already figured out that to get the cap off the valve cover unless one is 7 + feet tall its not going to be reached without standing on a step of some sort and so when I do that I put the right adapter in and just leave the elbow on the funnel all the time anyway and open the lid and then if using quart containers for sure I can stand beside the truck and leisurely add the oil, and I can leave that funnel on when starting the engine to let it idle to fill the filter and then add the rest of the oil to top it up before removing the funnel and putting the factory cap back on. I put the cap back on the top and slide the bottom cap on as it fits onto the elbow adapter also and then store the funnel in a clean household plastic garbage bag along with the adapter so I have no reason to be washing out the inside of the funnel as I keep it completely clean between uses.    Draining the oil as per the under the truck portion, yes indeed that is slick as someone was thinking on GM's part there and admittedly I don't drop the oil screaming hot in this truck due to the exhaust being there and makes it safer as far as the oil temp if its just warmed up some instead as I don't have the truck on any ramps etc as I do it as the tires sit on the garage floor. The filter is not boiling hot then either and can drop it off into another pail after pulling the drain plug and just leave it drip out. Go back under a few hours later with new filter in hand and clean off the filter base and put the new filter on and install the drain plug. The filter is a little cramped in there as per wrapping ones hand around the filter and I am so used to using the band style filter removal tool that its no big deal and same for snugging it up. My filter wrench is many years old now but I think this is the current version and sounds like the right size, just in case my explanation was not great ( those nylon strap wrenches that one tool fits all filters are not my favorite tool to use, I much prefer this style personally )     57020 Swivel Gripper - No Slip Filter Wrench - Small | Lisle Corporation   And again about the oil draining and filter setup under these GM trucks, I've watched Ford videos of them struggling with oil flying sideways out of the oil pan on the gas 7.3 due to the sideways drain plug onto other components or cross members and guys trying to make shields out of carboard etc and other Ford pickups that Ford insisted they have sideways drain plugs. One win for GM there anyway with this engine. 
    • Kind of off topic, wife drives a 2023 Yukon Denali with the 3.0, been a great rig so far, incredible fuel economy for a truck that big and heavy. Coming up on 50000 trouble free miles.
    • I`m gonna try some of this in my 2000 LM7 that has had the famous piston slap since 17,000 miles or so. I have used Mopar combustion chamber cleaner down the spark plug holes a few times in the past. Corrects the problem for a few months or so. Then returns. GM top engine cleaner has been used also. No good results from this.   This LM7 never used oil. Even running the piss out of it.   Course, I`m gonna use this in my 2025 L84 while it`s still clean. It`s got 13,000 miles. Used Chevron fuel system cleaner [2 bottles in tank] a tank or 2 ago.  
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...