Jump to content

Seat Movement Issues

jdvaughn

By jdvaughn
in Troubleshooting & Recalls

 Share

Recommended Posts

  • Replies 1.1k
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

hotrodz37
hotrodz37

So I was able to solve the seat movement issue as a few others with hose clamps. I bought 2 - 1" hose clamps, and 2 - 3/4" rubber clamps and slid the rubber off of those and onto the hose clamps. I bu

GMC-AT
GMC-AT

whatever... I'm sure 2013 Chevy was perfect and had no issue. I'm sure your 1996 Ford is also perfect and never had any issues ... The truth is that every car/truck, every year has it's issues. Th

tanner709
tanner709

Thanks for this.   Just re-quoting for all the new members because I spent about 20 minutes trying to find the fix, with pics.

Posted Images

TheElementalCashew Enthusiast

TheElementalCashew

Posted
Posted

For those of you who have (in the opinion of others) "wasted" there time on a dealer fix for this problem, only to have it come back again. Here is a permanent fix. What is happening is the dealer installed retainer clip is popping out of the white seat hinge which is allowing the seat to move again. By installing a hose clamp around the retainer clip it will not allow it to pop out and it will still allow full range of motion on the seat.

A 2" hose clamp and 5 minutes should take care of the problem FOREVER!! (I hope)

 

20151005_110437a.jpg

 

 

*EDIT* After looking closer at post #762 above, it appears the dealer was supposed to install a zip tie around the retainer clip to keep it in place. In my case...they didn't...hence the need for the hose clamp.

They did zip tie mine, and it has been holding solid for months now.

  • 2 weeks later...
Jimmy W Enthusiast

Jimmy W

Posted
Posted

Dealer fixed mineI just couldn't deal with knowing that I had hose clamps and rubber hose on my 50,000 truck to keep seat from moving!!

BabyJayne Enthusiast

BabyJayne

Posted
Posted

Hi All,

Well I took mine to the deal a couple months ago and so far so good. I did however save that pic that TheElementalCashew posted. You know just in case this crap starts all over again. If it starts again I will definitely let you all know. :fingersx:

:driving:

ZmanII Enthusiast

ZmanII

Posted
Posted

They installed my clip on the center console side of the seat, not the door side. All of the pictures I have seen show the clip on the door side of the seat. Can the clip be put on either side of the seat?

tbarn Senior Enthusiast

tbarn

Posted
Posted

They installed my clip on the center console side of the seat, not the door side. All of the pictures I have seen show the clip on the door side of the seat. Can the clip be put on either side of the seat?

The retainer goes on the outboard side per instructions. Can't say whether it makes a difference though.

ZmanII Enthusiast

ZmanII

Posted
Posted

The dealer installed the new clip on the center console side of my seat. This is incorrect, the clip wasn't connecting anything. I moved it to the door side of the seat where it connects the pivot block (white block) with the pivot bracket (metal bracket). It only took me about 15 minutes to put it on the proper side of the seat, for both seats. This probably explains why I didn't feel any improvement after the TSB was done. I tried taking a picture of how it was originally installed, but it didn't come out too good.

Redray Enthusiast

Redray

Posted
Posted

One week and my seat seems good as new. Now if the seat warmers would heat up a little faster.........

andyhaug Enthusiast

andyhaug

Posted
Posted

How many people have seats that shift front to back? Every time I stop it rocks forward slightly then back. It is more than just the seat shifting with weight, there is a loose feel to the seat allowing it to shift front to back. Just got mine back and the dealer assured me that it was "normal". The frustrating part is the 2000 Silverado I traded in did not do this.

Bigalsierra New Member

Bigalsierra

Posted
Posted

I got my brand new 2015 GMC Sierra in May' 2015.

 

I'm currently experiencing the similar seat movement issues since of late. I have given my truck in for a service this morning & have addressed this issue.

 

Hope they get it fixed by the end of the day.

JimCost2014 Senior Enthusiast

JimCost2014

Posted
Posted

andyhaug, the seat movement is not normal. call the Chevrolet 800 number to the customer service center. tell them that you want to open a claim on your truck. go in to great detail as into what it is doing and what the dealership is doing to help you. names at the dealership would also be helpful. these complaints go directly to department managers and the ownership of the dealership. these kind of things are frowned upon from Chevrolet as a failing grade for that dealership. give it a shot, you will be amazed at how quick something will start happening. can not guarantee it will be the results that you are looking for, but it will make the issue very visible to all involved.

andyhaug Enthusiast

andyhaug

Posted
Posted

Last time I talked to ERT they were completely backing the dealer. The dealer told me that it was normal based on others that they tested including a high country. On a trip for work now, I plan to go back and look at these others that make it normal.

Otherwise I am thinking of making an older generation seat slide in there, back when they actually cared. Anyone know how much different it is? Maybe I could just weld the existing one in place, at least it wouldn't rock anymore. If I wanted a rocking chair I would get a porch, not a new truck.

avgas Enthusiast

avgas

Posted
Posted

I took mine in on Wednesday and so far the issue is gone. They installed some shims and added clips of some kind. Both front seats were moving and both seem to be repaired.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • Grumpy Bear
      Some Assembly is Required

      By Grumpy Bear · Posted

      Common Sense Assembly   Your driveline is forgiving of the occasional mistake. It will even often forgive the random serious blunder. But it will not forgive a continuous bad habit.      What? Not everything needs to be a five thousand word essay.       
    • Grumpy Bear
      Gas Prices

      By Grumpy Bear · Posted

      We drove about 15 minute east today to visit a friend and saw a steep increase in price in the same county. About 50 cents a gallon steepper. 
    • Grumpy Bear
      Wow I'm in a pickle. (Broke down truck) and a story.

      By Grumpy Bear · Posted

      Sure about that? A degree wheel and a dial indicator would lower your degree of assurance in that statement. 😉    It why we have offset keys and dialable timing sprockets. Just say'n.... I've built a few and have never seen one "On the money". 
    • Chuck FB
      Tire psi

      By Chuck FB · Posted

      I will admit I haven't experimented much with pressure drops beyond the numbers I put in and part of that is that the numbers I used are fairly low and then found out it would trigger regardless at that 35 psi. Having said that I had tried before had changed the placard pressures and being that I have a 1 ton set to 80 on the placard for the rear I believe it triggered close to 60, the front I don't recall now for sure but thought maybe it could get close to 45 from that factory 60 placard pressure. So I never did figure out if it was a number of psi from placard pressure to the alarm or a percentage of the total placard number as some figured it was like a 25% drop from placard pressure would trigger it. So as to try and answer your question, I believe I set the placard pressure on the front to 47 or so and while I run the front tires at 40, they have dipped below that some if its colder and I haven't put "winter air" in yet and never once have had the front alarm go off. I would say that the answer your looking for is no, that if you set your placard pressure to 45, you have a certain amount of room to drop below that pressure before the alarm will go off.    The pressures you decide to run in your truck, that ends up being what makes sense to you based on what your carrying in your truck or if towing, then have to bump them back up to something that will carry the load in the rear and the fronts typically left at the same pressure. It all comes down to that chart I put the link to and using an accurate roadside scale to be your guide, both unloaded and then loaded to know your minimum safe pressures.    I just wish GM would allow a person to change the readings for the tire pressures to the English system of pounds as I have to look at that goofy metric reading that will never ever jive in my head and will go over and change it just to figure out what they are if need be and then change it back. 
    • TrueBlue
      No Software Updates - Old Build

      By TrueBlue · Posted

      That part I understand, that the dealer can do it. But I'm not understanding why updates that were available to the truck since it left the factory, or the dealership originally, would not still be available to it without dealer intervention.   I'm thinking along the lines of recalls. They stay available until they are completed, regardless of whether they are in warranty or not, or in the hands of the original owner or not. Why not updates as well, especially since some of those can be safety related also?

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...