Jump to content

Recommended Posts

  • 2 months later...
Posted

Hello everybody, I'm new here, but soon to have plenty of questions.  First off, however: my 2016 6L80 tranny just turned 70,000 km's (43,000 miles) - I have every intention of putting a Sonnax Zip Kit to boost shift pressure etc.  Keeping in mind I run my truck offroad on 32.5"'s regularly, and I'd like it to survive as long as possible, including future 35's.

 

My powertrain warranty is up in two years, which will likely mean about 100,000kms/60,000 miles; I intend to install the sonnax kit in parallel with an i3 tuner (hard shift setting) and 4.56 gears, which should all help the tranny in the long run.

 

In my experience...learned mostly the hard way...such kits are only beneficial if used while the transmission is healthy.  The question is: is 100,000km too late to put a zip kit in, or is it worth the risk to have it put in ASAP?

 

Short term risk-long term reward considerations here.

  • 3 weeks later...
Posted

hand held canned tunes wont make much power... because they cant touch the PE tables otherwise the FEDs will be on their ass, shutting them down for emmissions violations!  they may add some timing,  disable TQMnmnt, disable cyclinder deactivation, tighten the line pressure in the trans, thats about it.

the power is in the PE table

  • 4 weeks later...
Posted

I will say this after you receive a Tune run a Data Log after running the New Tune for 200 miles. Then have them check it mainly in the area of RPM Idle and Transmission Shifting/Performance.

I have noticed with the 2014 5.3 L83 and my nephews 2017 5.3 L83 after tuning the need to bump the Idle RPM's, very small adjustments. The 6L80 6speed Trans can produce nice results when tuned but it may take the extra Data Log to update the Tune for optimal performance and longevity. 

  • 3 months later...
Posted (edited)

I'm editing my original post.

 

2019 LD old body is the same access for tuning as 2018.  4 credits through HP Tuners, same E92A ECM.  My tuner got in no issue.  

Edited by newdude
  • Like 1
  • 3 months later...
Posted

I've had my 2014 6.2L for a few years now and I'm planning a tune.  The only reservation I have is, on the last page of my owner's manual, someone stuck an HPTuners sticker on it AND I've hit 130mph with no problem before...If someone removed the speed limiter, what are the chances my ECM would be locked and I couldn't tune with Blackbear? Can you just remove a speed limiter with HP Tuner?

Posted
23 hours ago, modernmetal said:

I've had my 2014 6.2L for a few years now and I'm planning a tune.  The only reservation I have is, on the last page of my owner's manual, someone stuck an HPTuners sticker on it AND I've hit 130mph with no problem before...If someone removed the speed limiter, what are the chances my ECM would be locked and I couldn't tune with Blackbear? Can you just remove a speed limiter with HP Tuner?

So just buy HPTuners then :)  - shouldn't be a problem though - HPTuners doesn't lock anyone out of doing anything. Worst case scenario the previous tuner locked the tune and then Justin just has to dig into his own tune repository for a stock file that would match your truck. 

  • 2 months later...
Posted (edited)
On 3/9/2020 at 4:46 AM, RET. NCO said:

 

I have noticed with the 2014 5.3 L83 and my nephews 2017 5.3 L83 after tuning the need to bump the Idle RPM's, very small adjustments. The 6L80 6speed Trans can produce nice results when tuned but it may take the extra Data Log to update the Tune for optimal performance and longevity. 

i would focus on the trans tune first, remove the lock up converter settings,  lock up should only occur in 5th and 6th gear, less wear and tear on the weak clutch.  reduce TM by 18-25%.  get your trans temps down to 120-130F street driving.  do the Fast trans relearn after any updates..

this should improve longevity up to 180,000 miles

 

there are a dozen more adjustments that need to be made, but start with the basics before going advanced

Edited by flyingfool
Posted

My first custom tune was a Diablew tune on my 2013 Black Diamond Avalanche with a used diablo tuner off flea bay; cost me about $350 total and it was well worth it; had greatly improved drivability that was most apparent when I took off the tune to drive it in for the trade - I couldn't believe how bad the stock slurped. The trade is a 2018 Suburban LT 4x4 5.3, and though I want to try a BB tune, they have crept up to around $700 these days. I'm sure they are great, but there is only so much a tune can do, and 7 hundy is most of what my new Corsa cost (it alone is fantastic). Instead, I opted for the diablosport tuner to again let Lew tune after I got my new exhaust installed, and flea bay has tuners. Much to my chagrin, I picked up a refurb factory diablosport for cheap, and put on the "Jammer CAI" tune that was on the tuner. Apparently, its a 91 tune specifically for that brand CAI, but since I have a Airaid Jr and a new Corsa sport, I figured an increased airflow tune would apply until I got a few tanks of 93 through the truck. I added 11% throttle increase plus AFM off to that tune and kept everything else the same. Its sweet. I'm not sure if I got lucky or what, but this thing breaks loose. Could be the Corsa effect (which is, BTW, the best exhaust I have ever owned), but man I am one happy mofo right now...

 

Update. Lost about 3mpg with that no afm 91 tune. Went to 93 diablo tune with afm, and got it all back, plus it seems to run a little bit better...

 

 

 

 

 

  • 9 months later...
Posted

I'd like to get my new Jasper 6speed transmission in my 2016 Silverado tuned. Anyone have any recommendations for someone in the Kentucky or Ohio area?

Posted (edited)
On 10/19/2021 at 8:21 AM, sage55 said:

I'd like to get my new Jasper 6speed transmission in my 2016 Silverado tuned. Anyone have any recommendations for someone in the Kentucky or Ohio area?

I bought the Flashpaq F5 and did some tuning myself - 91 Octane tune, AFM delete, tire size reset.
It does allow a tune for shift points.
To be fair, that's not something I'm interested in, but it can be done.
Oh, I did change the the speed tor the CC lock-up, so that can be done, as well.

https://superchips.com/shop/f5-flashpaq-for-2017-2020-gm-vehicles
 

2016:


https://superchips.com/shop/f5-gm-flashpaq
 

Edited by MikeBMW
  • Like 1
Posted
12 hours ago, MikeBMW said:

I bought the Flashpaq F5 and did some tuning myself - 91 Octane tune, AFM delete, tire size reset.
It does allow a tune for shift points.
To be fair, that's not something I'm interested in, but it can be done.
Oh, I did change the the speed tor the CC lock-up, so that can be done, as well.

https://superchips.com/shop/f5-flashpaq-for-2017-2020-gm-vehicles
 

2016:


https://superchips.com/shop/f5-gm-flashpaq
 

Looks like a pretty neat device, but to be honest I wouldn't have a clue how to use it or how to even program my transmission.

 

I'd love to find a local or semi-local guy that has done this and know what they are doing. Haha.

 

Otherwise I'm making the 12+ hour drive up to see @CamGTP :D 😉

  • Like 1
Posted
On 10/19/2021 at 8:21 AM, sage55 said:

I'd like to get my new Jasper 6speed transmission in my 2016 Silverado tuned. Anyone have any recommendations for someone in the Kentucky or Ohio area?

Dkgoodrich.com in Frankfort KY. He does HP tuners and really knows his stuff.

  • Like 1
  • Thanks 1
Posted
1 hour ago, Chad2815 said:

Dkgoodrich.com in Frankfort KY. He does HP tuners and really knows his stuff.

Frankfort is just around the corner from me. I'll be calling them tomorrow! Thank you so much!

  • Like 1
Posted
On 10/21/2021 at 7:09 PM, sage55 said:

Frankfort is just around the corner from me. I'll be calling them tomorrow! Thank you so much!

No problem, its easier to talk with him through text. If you want to go the handheld route I have a Hypertech Max Energy 2.0 that Im going to be selling soon. Let me know either way. 

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Latest Articles

  • Posts

    • Thanks - I wasn't quite caffeinated this morning. 2:1 makes sense, turning the crankshaft 360 degrees will turn the cam 180 degrees, and had I done that, the cam's dot would be at 6 and the crank's at 12 again.   I went ahead and took the sprocket off anyway, aligned everything dot-to-dot including the balance shaft just for s&g. I'm glad I did because I discovered no Loctite on the timing sprocket bolts. Maybe it's not required, but at only 20 ft-lb torque spec, those bolts aren't in there very tight. Cleaned and reassembled with some thread locker and torqued.   A general observation: Less is more with RTV. If a little doesn't stop a leak, a LOT probably won't, either. RTV is thinly veiled revenge, in a tube...      
    • The timing marks are ok, that is #1, you can turn it over until they line up and it won't change anything, the crankshaft turns twice for every camshaft revolution, I have always set up SB Chevs as your pic shows using a straight edge
    • Someone's been here before.... There is a receipt for a 3-piece timing set, purchased earlier this year.   Is this picture something, or, nothing?   I have the timing cover off and my crank is perfectly TDC and the keyed gear's locating mark is dead on 12 o'clock.   The cam gear locating mark is also at 12 o'clock. Now, I'm not an expert, but all the install guides say the two locating marks should meet and be perfectly aligned when installing a timing set. The mark on the crank should be dead on 12:00 and the cam gear's mark should be dead on 6:00, and both marks should be perfectly vertically aligned.   I believe the timing gear is keyed or has a dowel that ensures it can only be installed on the cam in one position, so I have to believe the cam is out of phase somehow. At the very least, with a triangular bolt pattern, it can only be installed in one of 3 different positions.   Before I pulled the front cover, the truck was running alright, no service engine soon lights except an occasional P0172 / rich condition. Timing -16 timing at idle (should be +16), and total -35% fuel trim, two conditions I haven't been able to figure out.   In related news, my injector tested pretty well, wasn't leaking, but I had it rebuilt anyway, and it's on it's way back to me.         Along with this discovery, the good and bad:   Good: The oil pan seal appears undamaged.   Bad: -The timing cover has been reused, and the positioning dowels have been broken. That could explain some of the leaking. -Some kind of white paste or grease was used to try to seal the oil pan seal and timing cover (since wiped off..). -Then, someone globbed silicone all over the front of the cover and also buried the ckp sensor in it. But, they didn't put any inside the cover or use RTV to try to seal the oil pan seal with the timing cover (good).
    • The guy that owns K&P filters last I checked in with him has over 300,000 miles on his Dodge base Hemi using his own 35 micron absolute stainless mesh filter from its first oil change.    The GM study I've posted a dozen times shows the relationship in engine life based in multiples of base units, not miles or years. That is the base unit is the number of miles the motor ran using the reference filter efficiency.    The above two paragraphs dismantle anecdotal arguments IF one changes oil often enough to prevent particle formation and the motor is in otherwise good shape. That is not full of silica (no air filter) or suffering a metallurgical issue that is not part of the lubrication discussion. Poor heat treat in example.   Data from UOA's I've reviewed from more than a few engines can show remarkably broad variations in oil cleanliness using the exact same filter over the course of an engines life.     Lastly there is the common sense of it. Wear debris WILL circulate the engine BEFORE it ever sees a filter in route to that filter and WILL harm the pump which NEVER sees filtered oil.    Alpha question then becomes, given the facts, how long do you believe is a reasonable service life from a vehicle you are certain you will not pass down? That is the junk yard will be it's resting place when you're done with it? (the moral issue most don't care about).    Omega question is then how diligent are you prepared to be in general mechanical, air & oil maintenance? Preventing particulates and keeping them sufficiently dilute; preventing the precursors from generation, amalgamation and precipitation.    If I get a good look at the engine bay of a vehicle I have a fair idea of the owners commitment to the inside of the power train. That 30 micron WIX is still more efficient than a sieve.                 
    • It also depends on what criteria someone is using for “best” when talking filters.  Are we going off best efficiency?   Best quality/QC?  Etc. because the two may not mutually exclusive.  
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...