Jump to content

Shake or Vibration Issues

Silver space ship
 Share

Recommended Posts

Kylebr1 Enthusiast

Kylebr1

Posted
Posted
14 minutes ago, evlwhtman said:

Meh, only difference in the consoles is rigidity. Nothing more than that. The less rigid the feature the more likely to develop some type of movement.

If it were that easy i would have a "flow through" console.

What i really mean by all of this is that i think a lot of people say they have a vibration issue because they can see the console move on the highway .. If you had the same truck but with a flow through centre console 

would you even notice the vibrations ? i know before i had my truck fixed the floor and seats didn't really vibrate more than a normal truck but the lid for the fold down seat always shook like crazy . 

  • Replies 12.9k
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

csckickass
csckickass

Well folks, I did it. After all the failed attempts at the Chevy dealer I traded it in for a 2015 Ram 1500 Larame. I have to agree with the other folks on here that have done the same thing, it was th

mafd2
mafd2

Apparently you and the other customer reps don't care. If you or GM would care y'all would put more effort in the matter. Just coming on the forum and stating the same repetitive posts and being a 3

DALaws
DALaws

Well I have some good news and bad news about my truck vibrations. Good news is that my truck has a significantly less vibration at speed. The bad news is my truck has significantly less vibration. Fo

Posted Images

fishrman Enthusiast

fishrman

Posted
Posted
On 8/28/2019 at 9:59 AM, fishrman said:

Sounds a bit redundant but thought I just as well add my 2 cents. Have had my 2017 Chev. 1500 Silverado LTZ 4x4 with 5.3 since last year when I bought it new as a carry over with about 50 miles on it. It is a pretty truck and I couldn't figure out why it was still on the lot. I am beginning to understand why after reading many of the remarks on this thread. 

When I first drove the truck, I told the salesman I felt a little vibration and thought the tires needed balanced. He told me he would have them balanced for me before purchase and did. The vibration I am getting is especially noticeable at first start after it has cooled off. It seems to improve at the lower rpm's after a few minutes of driving. I still notice some vibration at highway speeds that still feels like a broken belt in a tire or something but am now wondering if that really is what it is. I only have 5000 miles on the truck and finally asked the dealer about the issue at the first oil and tire rotation. He told me there was no service bulletins on the issue! (after reading this thread--I am not sure what he had been smokin before telling me that)! Anyway, I took it to another dealer who immediately told me there are known issues with the TC and he has scheduled an appt. for this next Weds. I will take it in on Tuesday night so it can sit and be nice and cool for the test drive in the A.M. He assured me that the mechanics are aware of the issue and they wouldn't need to put any diagnostic equipment on the truck but rather would be able to tell by driving the vehicle. Stay Tuned! Thanks for listening and any other thoughts are appreciated.

Well, just got a call from dealer telling me that they first thought it might be the transmission but they checked and the transmission had already had the latest programming had already been done on it so they looked further and put some new programming in the ignition control model but that he really wasn't thinking that helped but to "help put my mind at ease" the technician told him he checked everything out and that it might just be "the nature of the beast"!! Seriously???? Never even offered to change out the fluid in the TC or offer anything else!

fishrman Enthusiast

fishrman

Posted
Posted

Now I am told by dealer that the TC problem didn't apply to my 6 speed transmission-----tells me it is just the nature of the beast and happens because GM is trying to squeeze out all the mpg they can. My next step will be contacting GM directly!

2016DenaliGuy Enthusiast

2016DenaliGuy

Posted
Posted
On 9/2/2019 at 9:07 PM, 2016DenaliGuy said:

Bought a 2016 Denali 6.2L 4x4 last week with 53k miles on it.  Shame on me, I didn't do an interstate ride as part of my test.  Took a road trip to go camping over the weekend and when I got to 73 mph it was pretty bad.  It got worse as I increased speed to 80 ish.  I immediately started thinking bad tires/balance, but a quick search revealed that it's actually a thing. ?

 

That led me here.

 

So...I'm guessing I have about 6k miles of powertrain warranty, and should hit up the local GMC dealer about it before I get to 60k.  I'm assuming a RFB or regular balancing of the tires won't actually do any good at this point and should actually look at the service bulletin for the fluid flush or check into getting another driveshaft to start.  If I can't fix this I'll have to dump the truck. We do too many road trips as a family to deal with this.  Which is a shame.  It's such a nice looking pickup.

Update for me: 

 

Balancing the tires removed 90% of the vibration at speed.  Tech at Goodyear told me that all 4 were over 3 oz. out of balance.  He got them and and rotated them and I'm riding again.

 

I'm hesitant to say it's fixed but it's definitely much better.

 

 

Kylebr1 Enthusiast

Kylebr1

Posted
Posted
4 hours ago, 2016DenaliGuy said:

Update for me: 

 

Balancing the tires removed 90% of the vibration at speed.  Tech at Goodyear told me that all 4 were over 3 oz. out of balance.  He got them and and rotated them and I'm riding again.

 

I'm hesitant to say it's fixed but it's definitely much better.

 

 

This is how mine was when i was fighting to figure out what was causing the vibration . Balanced the wheels got a little better changed the axles got even better then was 100% gone with new driveshaft . 

Kylebr1 Enthusiast

Kylebr1

Posted
Posted
1 hour ago, Dearmosd said:

And what driveshaft did you end up using?

Had one made from a company called Pats drive-line I am in Canada so a lot of the american options are to pricey for me . 680$ Canadian i paid . 6" round aluminium one piece unit .  

2016DenaliGuy Enthusiast

2016DenaliGuy

Posted
Posted
On 9/5/2019 at 12:41 PM, 2016DenaliGuy said:

Update for me: 

 

Balancing the tires removed 90% of the vibration at speed.  Tech at Goodyear told me that all 4 were over 3 oz. out of balance.  He got them and and rotated them and I'm riding again.

 

I'm hesitant to say it's fixed but it's definitely much better.

 

 

Checking back in after a weekend of driving and I'm definitely harsh vibration free under 85 MPH.

 

For what it's worth, the carfax I have for the truck states that the torque converter was replaced in 2017 on this truck with 25k miles on it at the time.  So I think I'm good on that front.  I just want to get the driveshaft balanced and checked out to get any further contributors to the slight issue remaining resolved.

Kylebr1 Enthusiast

Kylebr1

Posted
Posted
On 9/9/2019 at 10:11 AM, 2016DenaliGuy said:

Checking back in after a weekend of driving and I'm definitely harsh vibration free under 85 MPH.

 

For what it's worth, the carfax I have for the truck states that the torque converter was replaced in 2017 on this truck with 25k miles on it at the time.  So I think I'm good on that front.  I just want to get the driveshaft balanced and checked out to get any further contributors to the slight issue remaining resolved.

From all the reading i have done i have not seen anyone re-balance there driveshaft and have it fix the vibration the issue is the driveshaft is made of paper thin aluminium and its full of cardboard . Because the driveshaft is so thin it resonates vibrations badly. 

2016DenaliGuy Enthusiast

2016DenaliGuy

Posted
Posted
17 hours ago, Kylebr1 said:

From all the reading i have done i have not seen anyone re-balance there driveshaft and have it fix the vibration the issue is the driveshaft is made of paper thin aluminium and its full of cardboard . Because the driveshaft is so thin it resonates vibrations badly. 

Hey Kyle - thanks for the advice.

 

I did hear from someone locally that took out their driveshaft and had a driveline shop do some analysis on it.  There was excessive runout in the middle of the shaft.  The shop put it on a lathe and made it run true.  Rebalanced it, and the guys vibrations were gone after that.  I was thinking about doing the same thing as far as having the machinist check it out.

 

Replacing with a high quality shaft is probably a good idea too, along with the upgraded axles.

Kylebr1 Enthusiast

Kylebr1

Posted
Posted
20 minutes ago, 2016DenaliGuy said:

Hey Kyle - thanks for the advice.

 

I did hear from someone locally that took out their driveshaft and had a driveline shop do some analysis on it.  There was excessive runout in the middle of the shaft.  The shop put it on a lathe and made it run true.  Rebalanced it, and the guys vibrations were gone after that.  I was thinking about doing the same thing as far as having the machinist check it out.

 

Replacing with a high quality shaft is probably a good idea too, along with the upgraded axles.

The factory driveshaft is 1/8" thick i don't think you could machine it at all . The unit i had made is 6" diameter and 1/4" thick .

neimadpc New Member

neimadpc

Posted
Posted

I've been following this thread for a long time, and thought I would share my experiences as well.

 

2017 Chevy Silverado Crew Cab - 35k miles

22" Wheels with Bridgestone Dueler AT's

 

I purchased this vehicle with 8k miles in 2017. I didn't notice the shaking/shimmy on my test drive. With my truck, it was only noticeable on smooth, long stretches. A lot of the highways around the dealership are pretty bumpy, and driving on them doesn't let the shimmy really set in. I could feel it at 40mph, on really SMOOTH roads. It was also bad around 70-80ish.

 

After about a week of driving it, i really started to notice the shake. I took it in 3 separate times and was told that the tech didn't notice anything unusual, and nothing wrong with it. I finally got really fed up with it and demanded a tech ride with me. I got one, and I took him to a section of roadway where I knew it would shake - he agreed something was wrong... Back to the garage.

 

I'll skip the rest and just tell you what they all did, over a period of time.

 

3 of the 4 tires were in the mid 30's for roadforce - I got 4 new ones (same Bridgestone Dueler AT's) - Still shook after that.

They found lateral runout on the rear axle - replaced left and right inner axle shafts - Still shook after that.

They found play in steering gear bushing - replaced steering rack - Still shook after that.

They replaced all shocks/struts - Still shook after that.

They replaced drive shaft - Still shook after that.

 

I drove it until my next oil change and when I brought it in, I asked if they had roadforce balanced the new tires when they mounted them, they did not. SO, I said do it on these new ones. 2 of the 4 new ones were in the low 30's again. Other two were 13 and 10.

 

Two more new tires, rf balanced at 9 and 11 - and its ALMOST completely gone. At this point I am going to just accept it as its almost non-existent and I'm so sick of dealing with it.

yojo Enthusiast

yojo

Posted
Posted

That is was GM hopes for ( to wear you down) Yes, they replaced the driveline. But when you replace Sh@# with Sh%^ you still have Sh#%!!!

Willyone Enthusiast

Willyone

Posted
Posted
16 hours ago, yojo said:

That is was GM hopes for ( to wear you down) Yes, they replaced the driveline. But when you replace Sh@# with Sh%^ you still have Sh#%!!!

 Exactly

Rick Murphy Enthusiast

Rick Murphy

Posted
Posted

I have been dealing with the vibration issue for several months now.I have a 2018 Silverado 5.3- 6 speed trans 2 wheel drive and I have 22,000 miles Mine is mostly felt in the steering wheel from 50 to 70 mph. The dealer started by changing the torque converter with no success. The next visit they changed my motor mounts and had no luck. The next visit they did the trans fluid flush and the road force balancing of the wheels and this last time in the shop they took the wheels off a brand new truck on the lot and did a lot of pico scope tests and they had my truck for two weeks They also road force balanced my wheels again. The service manager told me when I picked it up that all the pico scope readings were within spec and that there hands were tied from any further repairs This morning I got the number for GM and called them and they are connecting me with a senior service advisor to get my issue fixed By the way my truck vibrates exactly the same as when I first took it to the dealer

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • Chuck FB
      Fluid Change Questions

      By Chuck FB · Posted

      There would be one way of determining the quality of the factory oil although probably more than a typical oil lab test, and that would be to draw out some oil from a new truck and send a sample to a lab that could do a more elaborate test of the oil. The issue with too little oil in the diff may not be the lack of lubrication of the diff bearings and gears themselves ( although a lack of oil volume for cooling ) but the wheel bearings because at some point the oil would be too low to properly get onto the spinning axle or fed along the axle tube. That was the claim by the local dealer from a couple of trucks in recent years that had the wheel bearings fail and they figured from lack of sufficient oil due to a severe underfilled diff and some of the bearing material made its way to the diff and it got damaged as well so the axle housings were just replaced on warranty. But your right that if the diff is over filled by whatever margin that it causes more churning of the oil than is desirable and that is no good either and can cause a pinion seal to leak. Also old oil I believe can tend to loose some of its properties like antifoaming and another good reason to change the diff oil every so often. 
    • Z45
      Fluid Change Questions

      By Z45 · Posted

      I would be surprised if the diff's were not filled (with the cheapest gear lube) at the axle factory before being shipped to GM.  If you ever watched them building trucks they install the axles and all suspension parts with the frame upside down and then turn it over before its time to install the engine.     Too much gear lube in a axle can be worse than not enough especially with a lower quality GL where is get whipped up with entrained air (foam)  weakening its ability to lubricate.        
    • MORSNO
      Oil Consumption

      By MORSNO · Posted

      This is the 6.6 gasser section of the forum, you should either delete or modify your previous post as it is misleading for anyone looking for factual information on their 6.6 gas engine.
    • Atlas
      Wow I'm in a pickle. (Broke down truck) and a story.

      By Atlas · Posted

      Well....I've done my first intake gasket. Probably wrong, but...we'll see?   Ultra black on the china walls and 1/4" up onto the sides of the intake gaskets. Permatex High Tack (couldn't find Gaskachinch) on the head side of the intake gasket. I read wrong and it says you're supposed to put it on the mating surface of the head, not the gasket. Hoping it's like a PB&J sandwich where it doesn't matter what side the PB goes on so long as there's jelly. That crap is messy/sticky and I got a dab or two on the intake port openings, tried to wipe it off. Hopefully it won't be a big deal and will only aid in sealing.   Per instructions I left the intake (top side) of the gasket dry except for a light smear of RTV around the coolant ports. Wiggling the intake in there was a bear but I had help to free me of surrounding wiring/stuff but I was basically able to set it straight down lined up with the bolt holes.   I did not think to wait until the RTV skinned over but there probably was 5-10 minutes while it sat before installing the intake.   Bolts finger tight first. Then, followed the Chilton's manual pattern to snug them to 15 lb-ft.   Waited a little over an hour, and then did the final torque in sequence again to 35 lb-ft.   Yesterday I replaced the fuel pressure regulator and got my new "nut and bolt kit" (fuel lines) installed. Damn GM used security torx on the spider, which I don't have, so I got scammed at the local HW store for an off-brand security Torx bit set.   The new driver's door mirror arrived yesterday, so, there's a chance this thing could be running and road legal tomorrow? I don't want to get my hopes up.   This will be my first time stabbing a distributor, too. Although, lucky me, someone else marked the old distributor for removal previously, I did see that. (Someone's been here before!!). Engine is still at TDC so it *should* be just a matter of transferring the mark to the new dizzy and rotating it into place.
    • KARNUT
      2027 GMC Sierra: Official Discussion

      By KARNUT · Posted

      He has his dad’s newer truck he’s put away. He has several old cars he rotates between him and his family. I’ve seen a restored square body and a SS Chevy truck he’s sometimes drives. He did raffle off a new suburban recently. As much as he is watched if he drove new stuff as a rule we’d know it. It would be fine by me. I don’t care what people prefer. I got one more new one in me. I’d rather my wife get one. I can’t get her out of the Genesis. Don’t tell anyone. I want her to get an electric truck. I want to put a generator in the back. Just because. She hasn’t bit yet.

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...