Jump to content

Recommended Posts

Posted (edited)

Getting my truck tuned was the best thing I could have done. The torque converter...It’s either locked up or not. No more 4cyl mode. 
 

I had it done around 50k miles. Now at 103k, dropped the pan to do the trans filter and looked brand new inside. Just some metal on the magnet. 

oh and 30 hp and 30 tq across the whole curve running on 89 pump gas. 

 

Edited by DeePa
  • Like 1
  • 2 months later...
Posted
On 2/23/2021 at 4:50 PM, JMC65 said:

I purchased 2014 Silverado last spring, 83k miles. What a journey it has been. Did not notice the vibration on test drive. Chevy Shake and 4 cylinder mode shutter. (these are two separate issues). Also rough shifting. I'd like to share what modifications and upgrades I made that worked for me after much research and trips to the dealer. 

1. Road Force Balance. $0 by dealer

2. Hydrolic steering bushing $450. 1/2 price by dealer. Helped a little.

3. Custom steel drive shaft $400 installed by me (easy). This made huge difference! Chevy shake all but gone, 90%.

4. Range AFM Disabler. $175. No more 4 cylinder mode. No more shutter. No more burning oil. This is a no brainer.

5. Transmission tune up and inspection . Filter change and flush. $150. No more hard downshift. Still not crazy about the way it shifts overall but both dealers and trans specialist confirmed all normal for this truck, no issue.

 

Truck drives great now since all above work done last summer. Starting to like it again. I got a great deal on this truck so for me the additional expenses are still under book value. 

 

I hope this helps anyone experiencing same issues and saves you some time. 

 

 

My 2015 LT just started to vibrate at speeds around 70 MPH.  This just started at coincidently, 83k miles.  

 

I am the original owner and this s my first issue so far. The AFM for me is completely fine, nobody realizes it switches unless i tell them (dodged a bullet!)

 

Currently the truck drives smooth as it did on day 1 until recently.  Even under quick acceleration it drives smooth until 70ish.   

 

Thinking doing the custom steel driveshaft to hopefully solve the issue.  Is yours still doing good?  Do you think that has made the biggest difference?

 

Thanks for the guidance!

Posted (edited)

after tinkering with my slip tables on the TCC lock up, i found when in gear my truck likes 0 slip , but when in V4 mode and locked up, it vibrates and rumbles like crazy with zero slip, so i kept the 10-20 rpm slip in v4 , its smooth now.  better yet just disable v4 and it will feel good

 

with zero slip under Lock up in 4-6th gear there is no rumbles vibes, go figure?? seems the vibes might only come into effect when the TCC locks in V4 mode..

 

i definatly agree with the post above, , i feel like the truck is in its power band when you dont lock the converter and lug the motor down with lock up in 1-3rd gear, it really lets the L83 wind up and it feels like 20 hp upgrade for free.

Edited by pokismoki
  • Like 1
  • 3 weeks later...
Posted (edited)

Hello,  I’m not a engineer and I don’t know how/why this shimmy is there but personally, I think you all are overthinking the driveshafts, tires, and whatever else you all have mentioned. I sole heartedly believe it has something to do with the AFM system. Period. Mine only does it sometimes on the same exact roads at the same(cruise controlled) speeds. I can notice the tach bouncing and I can feel the truck reacting to that. That is usually when it starts shaking. When the afm isn’t acting up and causing this bounce in the tach, the truck doesn’t shake at all! Period! Rides as smooth as you would ever expect anything to ride. I’m saving up to buy a programmer to disable that pile of $hit AFM SYSTEM AS SOON AS I CAN! Maybe there are a few different shakes that occur with these?? Mine may not shake for 6 months and then all of the sudden, BOOM. Shaker Engaged! Then 8 hours later, no more shake. I would think if it was mechanical, out of balance, it could not possibly come and go. That is not how I see mechanical issues working. If a tolerance is out on something it doesn’t miraculously fix itself. Or I don’t see how that’s possible. Again, no mechanical engineer here. So sorry if this is a incorrect statement. Mine shakes more severe some times and barely others. Hard shakes rattle my keys hanging from my ignition. And like I said, you can clearly see the tach bouncing… sometimes up to 400 rpm’s. If I get this thing tuned and it stops, I’ll try to remember to come back and let you know. I could be wasting my time, but at least in the end I’ll have that shitty AFM disabled! Dumbest thing ever for an engineer to come up with. In my opinion. 
 

have a great day! And shake on! 
 

p.s. GM should be ashamed to allow such a deal to continue and expect their customers to figure this out on our own dime. Obviously they don’t care for their customers and time will tell how many they will lose over issues such as this! 
 

2017 Silverado. 5.3L. Z71 LTZ CREW CAB. Short box 

 

I’ve also had issues with leaking windshield(from factory). Braking issues that was never fixed by the dealer with the recall, although they put it in the system as the recall being done. Now the brakes still go in operable at low speeds and they expect me to pay since the recall was “Done” and it has to “be something else”. Notably, the truck does have a “prior salvaged” title (from cosmetic/body damage, absolutely no mechanical items were ever touched other than tires removed to complete repairs!). So that’s their out and to me, it’s ridiculous. Scraping some paint off fenders and a hood doesn’t damage the internals of the vehicle. I love the truck, but GM has some serious customer service issues to resolve in order for me to buy another one. 

Edited by Richard F
  • Confused 1
Posted
49 minutes ago, Richard F said:

Hello,  I’m not a engineer and I don’t know how/why this shimmy is there but personally, I think you all are overthinking the driveshafts, tires, and whatever else you all have mentioned. I sole heartedly believe it has something to do with the AFM system. Period. Mine only does it sometimes on the same exact roads at the same(cruise controlled) speeds. I can notice the tach bouncing and I can feel the truck reacting to that. That is usually when it starts shaking. When the afm isn’t acting up and causing this bounce in the tach, the truck doesn’t shake at all! Period! Rides as smooth as you would ever expect anything to ride. I’m saving up to buy a programmer to disable that pile of $hit AFM SYSTEM AS SOON AS I CAN! Maybe there are a few different shakes that occur with these?? Mine may not shake for 6 months and then all of the sudden, BOOM. Shaker Engaged! Then 8 hours later, no more shake. I would think if it was mechanical, out of balance, it could not possibly come and go. That is not how I see mechanical issues working. If a tolerance is out on something it doesn’t miraculously fix itself. Or I don’t see how that’s possible. Again, no mechanical engineer here. So sorry if this is a incorrect statement. Mine shakes more severe some times and barely others. Hard shakes rattle my keys hanging from my ignition. And like I said, you can clearly see the tach bouncing… sometimes up to 400 rpm’s. If I get this thing tuned and it stops, I’ll try to remember to come back and let you know. I could be wasting my time, but at least in the end I’ll have that shitty AFM disabled! Dumbest thing ever for an engineer to come up with. In my opinion. 
 

have a great day! And shake on! 
 

p.s. GM should be ashamed to allow such a deal to continue and expect their customers to figure this out on our own dime. Obviously they don’t care for their customers and time will tell how many they will lose over issues such as this! 
 

2017 Silverado. 5.3L. Z71 LTZ CREW CAB. Short box 

 

I’ve also had issues with leaking windshield(from factory). Braking issues that was never fixed by the dealer with the recall, although they put it in the system as the recall being done. Now the brakes still go in operable at low speeds and they expect me to pay since the recall was “Done” and it has to “be something else”. Notably, the truck does have a “prior salvaged” title (from cosmetic/body damage, absolutely no mechanical items were ever touched other than tires removed to complete repairs!). So that’s their out and to me, it’s ridiculous. Scraping some paint off fenders and a hood doesn’t damage the internals of the vehicle. I love the truck, but GM has some serious customer service issues to resolve in order for me to buy another one. 

I have to disagree with you that it is only related to AFM and torque converter. I have AFM disabled and did that a long time ago. You could be right though about torque converter contributing as it along with the GM trans have been know to have many issues. But there doesn't seem to be a one fix fits all. On mine, when it was really bad, getting my tires road forced balanced improved the shake tremendously. But I still sometimes get it. I now have a new set of tires installed maybe a year ago and I probably need to get those RFB'd as well. But I have also noticed that it only occurs on certain roads too.  Not sure why but besides the multitude of "fixes" suggested, maybe road surface is also a contributing factor? Another thing I seem to notice is that it is different if I have a full or nearly empty fuel tank as well as if I have several people or by myself, or an empty bed or carrying a load. No idea but on mine, the shake only pops up occasionally and is more of a minor irritation now so I just ignore it most of the time. 

Posted

Little to no doubt GM knows what the cause or causes of the shake is. It's likely an expensive fix, so they choose to thumb their nose at the buyer/customer and ignore the problem.... shame on GM, especially after the bail out. GM sucks, plain & simple. I know two people who got rid of their GM trucks and went to another brand and are quite pleased with their move. Funny, in a recent mailing/sales pitch I received from GM they had a bunch of verbiage regarding how they plan to, for lack of better words, get on the "woke" band wagon. Very impressive that they indicate how much they care, when they really don't. Rant over...

Posted

i just discovered the trans mount bushing on my 2016 truck was missing the nut that bolted it to the trans crossmember, basically the trans was resting on the crossmember allowed to float and vibrate against it.  just purchased the oem nut from GM, i dont feel any vibes .. cost $12

 

 

  • Like 1
  • Thanks 1
Posted

Somebody's had the trans out, probably to replace the converter or install updated anti drainback valve. Are you original owner?

Posted

trans has never been touched by dealer, i'm origional owner, did the first filter change yesterday, and was pushong up on the shaft yoke and was shocked i could lift the rear tailshaft off the rubber mount.

  • Like 2
Posted
20 hours ago, Willyone said:

Little to no doubt GM knows what the cause or causes of the shake is. It's likely an expensive fix, so they choose to thumb their nose at the buyer/customer and ignore the problem.... shame on GM, especially after the bail out. GM sucks, plain & simple. I know two people who got rid of their GM trucks and went to another brand and are quite pleased with their move. Funny, in a recent mailing/sales pitch I received from GM they had a bunch of verbiage regarding how they plan to, for lack of better words, get on the "woke" band wagon. Very impressive that they indicate how much they care, when they really don't. Rant over...

Worst trucks on the road currently. And I've had every brand. 

Posted (edited)

i think they are the better designed trucks in terms of reliability with simple 6 speed and pushrod LS motors. i do feel GM is sabatoging thier products with engineered in defects or quirks. this is something they do in the past with other models that where hits with the public, like B-bodie, G-bodies, 1990-96 Caprice/SS impalas, Fiero, square body Blazer, Chevelle, etc, etc....

Edited by pokismoki
  • Like 1
Posted

Been having this vibration in my truck for awhile now. I had my diff fluid and rear end fluids changed to Amsoil and at least since then had this vibration sound. It goes away over probably 50 percent throttle. Any idea what this might be? Ignore the ice jiggling in the cup. 
 

https://imgur.com/a/ouRGGyz

  • 3 weeks later...
Posted (edited)

My truck will vibrate sometimes where u can see the console moving 1/4" back and forth, even the passenger seat will shake. It really pisses me off considering how much the truck cost. Truth be told I feel like I am driving a pos most times because of the issue and lack of knowing how to fix it. Pretty disappointing...

 

It baffles me that GM has not been able to tell their customers what the issue is and what the fix is. 

Edited by Ge0rge
  • 3 weeks later...
Posted
On 7/20/2021 at 9:14 PM, Ge0rge said:

My truck will vibrate sometimes where u can see the console moving 1/4" back and forth, even the passenger seat will shake. It really pisses me off considering how much the truck cost. Truth be told I feel like I am driving a pos most times because of the issue and lack of knowing how to fix it. Pretty disappointing...

 

It baffles me that GM has not been able to tell their customers what the issue is and what the fix is. 

   There are many causes for the vibrations in the 2014 to 2018 generation of Silverados. Some happen when the motor changes to V4 mode for fuel economy,which is a common one but at least that one can be fixed with a workaround by the customer,not an official fix from the dealer. There are many other circumstances and causes  where vibrations occur at different speeds etc.

   I had one very similar to what you have and it only happened on the highway at speeds above 60 mph. The service manager at the dealer knew what I was talking about as soon as I mentioned it and they went through a big dog and pony show with several visits for service and ultimately said it was a normal characteristic and nothing could be done to fix it.

   Chevrolet corporate customer service was no help,they basically said there was no failed repair because no problem was found. The service manager and some of the techs even made remarks about Lemon Law,probably because others had done do and they  figured I would also.

   I ended up getting a Lemon Law lawyer online and he said he had handled hundreds of similar cases with GM trucks of that generation. I ended up getting a cash settlement from GM that covered the depreciation to that date.

    My truck was a brand new 2018 and it did it soon as I got on the highway after I picked it up from the dealership.

I ended up trading it in when it was six months old with 2000 miles on a new F150 which has been fine so far. Didn't really end up in the hole due to the settlement.  

   All this after having purchased 5 new GM vehicles over the last 25 years and it didn't matter to GM Customer Service ,at which point I told them I was through as a GM customer.

   As far as I know this is not a problem with the new generation of trucks that started in 2019. 

  • 4 weeks later...
Posted
On 8/9/2021 at 3:33 PM, bumtruck said:

   There are many causes for the vibrations in the 2014 to 2018 generation of Silverados. Some happen when the motor changes to V4 mode for fuel economy,which is a common one but at least that one can be fixed with a workaround by the customer,not an official fix from the dealer. There are many other circumstances and causes  where vibrations occur at different speeds etc.

   I had one very similar to what you have and it only happened on the highway at speeds above 60 mph. The service manager at the dealer knew what I was talking about as soon as I mentioned it and they went through a big dog and pony show with several visits for service and ultimately said it was a normal characteristic and nothing could be done to fix it.

   Chevrolet corporate customer service was no help,they basically said there was no failed repair because no problem was found. The service manager and some of the techs even made remarks about Lemon Law,probably because others had done do and they  figured I would also.

   I ended up getting a Lemon Law lawyer online and he said he had handled hundreds of similar cases with GM trucks of that generation. I ended up getting a cash settlement from GM that covered the depreciation to that date.

    My truck was a brand new 2018 and it did it soon as I got on the highway after I picked it up from the dealership.

I ended up trading it in when it was six months old with 2000 miles on a new F150 which has been fine so far. Didn't really end up in the hole due to the settlement.  

   All this after having purchased 5 new GM vehicles over the last 25 years and it didn't matter to GM Customer Service ,at which point I told them I was through as a GM customer.

   As far as I know this is not a problem with the new generation of trucks that started in 2019. 

Check out TSB 18-NA-355.  Root cause solution may be fluid upgrade to eliminate TCC issues.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Latest Articles

  • Posts

    • Coming back from towing a car to my daughter in Nashville truck started making a screaming noise from underneath.  Pulled over placed in park and sure enough whining noise from underneath.  Dropped at the dealer fearing new tranny or another front pump/cover replacement.  Service writer said it sounded like the tranny too...  Well $300, new idler and a belt all is good.  Pop the hood and give a listen. lol  Now I'm telling dealers I'm no longer interested in a new truck.
    • HD uses the 6.6 gas.   Oil consumption while heavy working is considered normal.  1 quart per 100 gallons of fuel is the normal rate above 8600lbs GVWR.  If more than that, it is considered excessive.   They will have to perform an oil consumption test using the guidelines in TSB 03-06-01-023J.     Information on Engine Oil Consumption Guidelines All engines require oil to lubricate and protect the load bearing and internal moving parts from wear including cylinder walls, pistons, and piston rings. When a piston moves down its cylinder, a thin film of oil is left on the cylinder wall. During the combustion process, part of this oil layer is consumed. As a result, varying rates of oil consumption are accepted as normal in all engines. Oil Consumption Oil usage has a direct relationship with the amount of fuel used. The harder an engine works, the more fuel and oil it will use. Therefore, oil usage as a factor of fuel usage is a more accurate indicator of acceptable oil consumption levels than vehicle mileage for vehicles at or above 8600 GVW. The accepted rate of oil consumption for gasoline engines in vehicles at or above 8600 GVW is 1 liter (1 qt) within 400 liters (100 gallons) of fuel used. This rate only applies to vehicles under warranty, maintained in accordance with the appropriate maintenance schedule, driven at legal speeds and within design intent of the vehicle. Many factors can affect an owner's concern with oil consumption. Driving habits and vehicle maintenance vary from owner to owner. Thoroughly evaluate each case before deciding whether the vehicle in question has abnormal engine oil consumption. Gasket and External Leaks Inspect the oil pans, engine covers, and the engine oil cooler for leakage. Inspect for oil leakage into the engine coolant. Improper Reading of the Oil Level Indicator (Dipstick) The vehicle must be parked on a level surface to obtain accurate oil level readings. Verify that the dipstick tube is fully seated in the block. When checking the oil level, make sure the dipstick is wiped clean before taking an oil level reading and fully depress the dipstick until the shoulder bottoms out on the dipstick tube. The dipstick should be the proper part number for the engine/vehicle that is being checked. Not Waiting Long Enough After Running Engine to Check Oil Level The vehicle should be allowed to sit for at least 15 minutes, after the engine has been shut off, before taking an oil level reading to assure the oil has had enough time to drain back into the crankcase. In order to ensure accurate results, the temperature of the oil should be close to the same temperature as the last time the oil level was checked. Improper Oil Fill After an Oil Change Following an oil change, verify that the proper amount and type of oil was put in the engine and that the oil level on the dipstick is not above the full mark or below the add marks. Refer to the Owner's Manual or Service Manual for information on recommended oil quantity, viscosity, and quality. High Speed or High RPM Driving Continuous driving at high speeds/high RPMs may increase oil consumption. Because this may not always be an everyday occurrence, it is hard to determine exactly how much the oil economy will be affected. Towing or Heavy Usage Towing a trailer or hauling additional weight will increase oil consumption. Large frontal area trailers will further increase the work required from the engine, especially at highway speeds, and thus increases the rate of oil consumption. PTO Operation Operation of a PTO will increase fuel and oil usage, as the PTO driven accessory uses engine power to operate. Crankcase Ventilation System Verify that the positive crankcase ventilation (PCV) system is operating properly. Blockages, restrictions, or damage to the PCV system can result in increased oil use. Oil Dilution from Condensation On vehicles that are usually driven short distances, less than 8 km (5 mi), especially in colder weather, condensation generated from cold engine operation may not get hot enough to evaporate out of the oil. When this occurs, the dipstick may indicate that the oil level is over-full. Subsequent driving on a trip of sufficient length to enable normal engine operating temperature for 30 minutes or more, in order to vaporize excess moisture, may give the customer the impression of excessive oil consumption. Engine Temperature If an engine is run at overheated temperatures (see Owner's Manual or Service Manual) for more than brief periods, oil will oxidize at a faster than normal rate. In addition, gaskets may distort, piston rings may stick, and excessive wear may result. Verify that all cooling system components are in proper working order. Engine Wear Piston scuffing, excessive piston-to-wall clearance, tapered or out of round cylinders, worn, damaged or improperly installed valve guides, seals and piston rings will all cause an increase in oil consumption. Measurement of Oil Consumption Engines require a period of time to BREAK IN so that moving parts are properly seated. Therefore, oil economy should not be tested until the vehicle has accumulated at least 6400 km (4000 mi). An exception would be allowed only if an engine is reported to be using more than 0.946 liter (1 qt) in 1600 km (1000 mi).   Verify that the engine has no external leaks. Repair as necessary. Verify that the engine is at normal operating temperature (see Owner's Manual or Service Manual). Park the vehicle on a level surface. Wait at least 15 minutes, after the engine is shut off, before checking the oil level to make sure that most of the oil has had time to drain back into the crankcase. Check the oil level and record the vehicle mileage, date, and exact oil level on the form included in this bulletin. Next ensure the oil level is at, but not above, the full mark on the dipstick. add oil if necessary. Also ensure the proper viscosity and quality oil are being used as recommended in the Owner Manual Ask the customer once they have consumed 100 gallons of fuel schedule an appointment and return to the dealer for inspection. If the final evaluation shows that the engine uses more than 0.946 liter (1 qt) in 379 liters (100 gallons) of fuel used, follow the published symptom diagnostics as described in the appropriate Service Manual. If the oil consumption test shows that the engine uses less than 0.946 liter (1 qt) in 379 liters (100 gallons) of fuel used, explain to the customer that their engine meets the guidelines for oil consumption.  
    • I have a 2024 Chevy Silverado 2500 with the 6.2 liter engine, Vin: 2GC4YME79R1273849, with 27,437 miles. Recently we took a trip from Candor, NY to Townsend, TN pulling our fifth wheel, when I got close to the Townsend, TN area The truck gave me a message of low oil. I checked the dip stick and found it was 2 quarts low. Today, August 27, 2026, I had the oil changed and the technician Found the truck was very low on oil.  Is there a Recall for this? What is my recourse for this issue? Do I call the dealer where I bought it or any chevy dealer?   Robert Strickland 292 Owego Road Candor, NY 13743 352-502-6588 [email protected]
    • We understand the importance of understanding how your Sierra performs, @SoCal Angler. Our team would like to gather the proper details to assist you with your inquiry about your truck's automatic braking. When you have a moment, please visit: https://s.chevy.com/support-request and fill out the request form with pertinent details. This will ensure your request is routed correctly so we may take a further look. We will keep an eye out for your outreach.
    • That is the funnel kit I bought and for being here in Canada I did get a better deal than what other sources were charging through a certain supplier in town that sources more directly and they ordered it for me. There are other items now on the market which would be perfect as well but this has worked well which was the hope when I bought it. I mentioned the Amsoil quart bottles as they have that squarish shape up top and it props nicely on the rim of the opening without falling into the funnel so I can leave them sit and drip a bit. You may have already figured out that to get the cap off the valve cover unless one is 7 + feet tall its not going to be reached without standing on a step of some sort and so when I do that I put the right adapter in and just leave the elbow on the funnel all the time anyway and open the lid and then if using quart containers for sure I can stand beside the truck and leisurely add the oil, and I can leave that funnel on when starting the engine to let it idle to fill the filter and then add the rest of the oil to top it up before removing the funnel and putting the factory cap back on. I put the cap back on the top and slide the bottom cap on as it fits onto the elbow adapter also and then store the funnel in a clean household plastic garbage bag along with the adapter so I have no reason to be washing out the inside of the funnel as I keep it completely clean between uses.    Draining the oil as per the under the truck portion, yes indeed that is slick as someone was thinking on GM's part there and admittedly I don't drop the oil screaming hot in this truck due to the exhaust being there and makes it safer as far as the oil temp if its just warmed up some instead as I don't have the truck on any ramps etc as I do it as the tires sit on the garage floor. The filter is not boiling hot then either and can drop it off into another pail after pulling the drain plug and just leave it drip out. Go back under a few hours later with new filter in hand and clean off the filter base and put the new filter on and install the drain plug. The filter is a little cramped in there as per wrapping ones hand around the filter and I am so used to using the band style filter removal tool that its no big deal and same for snugging it up. My filter wrench is many years old now but I think this is the current version and sounds like the right size, just in case my explanation was not great ( those nylon strap wrenches that one tool fits all filters are not my favorite tool to use, I much prefer this style personally )     57020 Swivel Gripper - No Slip Filter Wrench - Small | Lisle Corporation   And again about the oil draining and filter setup under these GM trucks, I've watched Ford videos of them struggling with oil flying sideways out of the oil pan on the gas 7.3 due to the sideways drain plug onto other components or cross members and guys trying to make shields out of carboard etc and other Ford pickups that Ford insisted they have sideways drain plugs. One win for GM there anyway with this engine. 
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...