Jump to content

Custom Trail Boss Console Upgrade?

Texas_Trail_Boss
 Share

Recommended Posts

Dea1276 Enthusiast

Dea1276

Posted
Posted
1 hour ago, ltdmstr said:

Does anyone have a photo of this part (84647286)?  Just want to confirm it's the right thing before I order one as there's a 20% restock fee plus shipping costs if returned.

Sure the guys that have ordered will post them once they get their parts installed. Thanks to everyone figure this out, and taking the plunge on ordering the parks! Looking forward to the install photos.

  • Like 1
  • Replies 401
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

MisterEhEDC
MisterEhEDC

So I decided to peek inside the the top of the jumper seat today and I snapped some pictures for you guys. Here is my piece of the puzzle.   It looks like the lower portion of the arm rest h

Jeffed
Jeffed

I purchased the upper part of the armrest from the dealer for $490 Cdn$.  The bottom part apparently is multiple part and was super expensive (i think about $1000).   Anyways, it was a bit of wor

Little Rascal
Little Rascal

I will give a summary of what I did.  Not being mechanical at all, it wasn't easy but very doable.    The first step was to take the plastic side panels off the console.  Right off the bat,

Posted Images

tanner709 Enthusiast

tanner709

Posted
Posted
1 hour ago, ltdmstr said:

Well, I want ahead and ordered the part anyway.  Will post photos when it arrives.  Also ordered the fog lamp kit (84125494).

what did each of these run you $?

tomleo67 Enthusiast

tomleo67

Posted
Posted
1 hour ago, ltdmstr said:

Well, I want ahead and ordered the part anyway.  Will post photos when it arrives.  Also ordered the fog lamp kit (84125494).

YES PLEASE! TY

Brutus230 Enthusiast

Brutus230

Posted
Posted

Where are the pic's for the arm rest.  Surely some one will share so we all can have it.

 

Please post. 

Jeffed Enthusiast

Jeffed

Posted
Posted

I purchased the upper part of the armrest from the dealer for $490 Cdn$.  The bottom part apparently is multiple part and was super expensive (i think about $1000).  

Anyways, it was a bit of work, but at least I have a bit of storage.  I can deal with that issue now.

You need to remove the driver seat and will require a T50 and T55 bit. 

20190613_120503_resized.jpg

20190613_120514_resized.jpg

20190613_120518_resized.jpg

  • Like 5
  • Thanks 1
Jeffed Enthusiast

Jeffed

Posted
Posted
1 minute ago, Brutus230 said:

Looks good.  DO you have all the part numbers you ordered to make this work. 

Its that #8464-7286.

There are 5 clips that hold the two plastic side pieces on.  You could probably take the old ones out and use them, but I just got new ones.  Was worried that I would squish them. I'm a bit impatient sometimes.  The clips are #8426-3801 if you want.  They were $3.76 CDN.

  • Like 2
Brutus230 Enthusiast

Brutus230

Posted
Posted

I thought 84647286 is the top part.  and there was another for the bottom.  when I take the top off mine it fill of foam. 

  • Like 1
Jeffed Enthusiast

Jeffed

Posted
Posted
Just now, Brutus230 said:

I thought 84647286 is the top part.  and there was another for the bottom.  when I take the top off mine it fill of foam. 

It is the entire upper section.  It includes the seatbelt. Here is the old one to see what you get.

20190613_123728.jpg

  • Like 1
Brutus230 Enthusiast

Brutus230

Posted
Posted

Thanks I think this will help us all.  we all want to fix this terrible thing chevy has done. 

Jeffed Enthusiast

Jeffed

Posted
Posted
Just now, Brutus230 said:

Thanks I think this will help us all.  we all want to fix this terrible thing chevy has done. 

I can deal with the other missing things, but the storage drove me insane.  Worth the money for my sanity.

Brutus230 Enthusiast

Brutus230

Posted
Posted

Ok I just ordered it cant wait to have a normal truck.  Just got the fog light in and getting it flashed tomorrow so they work. Thanks for taking the time there not many helping.

  • Like 1
Jeffed Enthusiast

Jeffed

Posted
Posted
1 minute ago, Brutus230 said:

Ok I just ordered it cant wait to have a normal truck.  Just got the fog light in and getting it flashed tomorrow so they work. Thanks for taking the time there not many helping.

Of course. It was a bit difficult to order the parts initially.  My dealer is good to me and sourced it out, basically just one from the LT models.  I would have liked to change the bottom section too, but they gave up once they started adding all the parts. Not worth that money.

Though about the fog lights. Let me know, maybe I'll do that someday..

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • Another JR
      Gasser Subforum Has Been Quiet - - So, Regenerative Braking and Using L10

      By Another JR · Posted

      Have considered installing a DC to DC charger in your camper to replace your isolator?  
    • newdude
      Gas fill door

      By newdude · Posted

      Common failure.  You need to replace the fuel door housing.   The painted cover transfers over to the new housing.  To remove the old one there is 4 spots where you poke the plastic to release it.  
    • newdude
      Gasser Subforum Has Been Quiet - - So, Regenerative Braking and Using L10

      By newdude · Posted

      No such thing as regenerative braking on a pure ICE vehicle.     Regenerative braking is the re-capture of energy from electric motors and stores it in the battery pack.  So hybrids, PHEV and EVs have regenerative braking.     What you are seeing is the charging system changing modes is all.  Its likely entering charge mode for some sort of reason is all.  All of the charging modes will be listed below.   As for L10 vs D.  L10 turns off automatic grade braking.  L10 puts you in control of grade downshifts where in D it will automatically do it based on brake pedal position and other factors.  Otherwise L10 and D drive exactly the same aside from that one aspect.    Battery Sulfation Mode The BCM will enter this mode when the interpreted Generator output voltage is less than 13.2 V for 45 minutes. When this condition exists the BCM will enter Charge Mode for 2–3 minutes. The BCM will then determine which mode to enter depending on voltage requirements.   Charge Mode The BCM will enter Charge Mode when ever one of the following conditions are met:   Windshield wipers are ON for more than 3 s. Climate Control Voltage Boost Mode Request is true, as sensed by the HVAC control module via serial data. High speed cooling fan, rear defogger, and HVAC high speed blower operation can cause the BCM to enter the Charge Mode. The estimated battery temperature is less than 0°C (32°F). Battery State of Charge is less than 80%. Vehicle speed is greater than 145 km/h (90 mph) A current sensor malfunction exists. System voltage is determined to be below 12.56 V When any one of these conditions is met, the system will set targeted generator output voltage to a charging voltage between 13.9–15.5 V, depending on the battery state of charge and estimated battery temperature.   Fuel Economy Mode The BCM will enter Fuel Economy Mode when the estimated battery temperature is at least 0°C (32°F) but less than or equal to 80°C (176°F), the calculated battery current is less than 15 A and greater than −8 A, and the battery state-of-charge is greater than or equal to 80%. Its targeted generator output voltage is the open circuit voltage of the battery and can be between 12.5–13.1 V. When fuel economy mode is active, the generator is not charging, only maintaining open circuit battery voltage. The BCM will exit this mode and enter Charge Mode when any of the conditions described above are present.   Headlamp Mode The BCM will enter Headlamp Mode when ever the head lamps are ON (high or low beams). Voltage will be regulated between 13.9–14.5 V.   Start Up Mode When the engine is started the BCM sets a targeted generator output voltage of 14.5 V for 30 s.   Tow/Haul Mode (if applicable) Pressing the Tow/Haul Mode button located on the center stack, the vehicle system voltage is raised and the remote (non-vehicle) battery will be charged. Having the headlamps on will raise the system voltage and if the Tow/Haul button is applied it will not serve any purpose. The voltage is regulated between 13.9-14.5 V.      
    • jaszr2
      Active Grille Delete

      By jaszr2 · Posted

      Hello from Australia Just sharing that there is now a way to delete the active shutters entirely with just a plug in module. Opens up tons of room to light bars etc.
    • jake111
      Gasser Subforum Has Been Quiet - - So, Regenerative Braking and Using L10

      By jake111 · Posted

      I have an observation and a question... 1) I watch the voltage closely because I have had to dial in the cut-in/cut-out voltages of the battery separator to my camper.  The "smart" charging drives me nuts.  Anyway, I noticed that when coasting for a while, and especially if lightly using the brakes (though not necessary), the voltage goes up from mid/high-13 volts to mid/high-14 volts.  Then it drops back down after stopping or going again.  Consistently!   The only explanation I can come up with is REGENERATIVE BRAKING!  Well, maybe that's a little bit of an exaggeration, but it's certainly free extra battery charging.   2) Driving on mountain roads I will use L and vary the max gear.  Things straighten out and I end up in L10.  Sometimes I leave it there for a while.  Is there any difference between L10 and D?   

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...